Subscribe to Our Youtube Channel
Summary of Contents for Amit APBDG0L031K0FA
- Page 1 APBDG0L031K0FA Panel computer for rolling stock Operation manual Version 1.01 apbdg0l031k0fa_g_en_101...
- Page 2 APBDG0L031K0FA AMiT, spol. s r. o. does not provide any warranty concerning the contents of this publication and reserves the right to change the documentation without obligation to inform anyone or any authority about it. This document can be copied and redistributed under following conditions: 1.
-
Page 3: Table Of Contents
APBDG0L031K0FA Contents History of revisions ..................4 Related documentation ................... 4 Introduction ..................5 Technical parameters ................6 2.1. Dimensions ..................... 9 2.2. Recommended drawing symbol ..............10 2.3. Block diagram ....................11 Product marking ................12 3.1. Producer type label ..................13 Conformity assessment .............. -
Page 4: History Of Revisions
APBDG0L031K0FA History of revisions Document name: apbdg0l031k0fa_g_en_101.pdf Author: Marian Schaubmar, Martin Uhlář, Václav Štěpán Revision Date Changes 4. 12. 2015 New document 8. 1. 2016 Chapter Audio modified. Related documentation Panel computers APBxxx series – Programming manual file: apbxxx_ms_en_xxx.pdf Panel computers APBxxx series – Service manual file: apbxxx_mr_en_xxx.pdf... -
Page 5: Introduction
APBDG0L031K0FA 1. Introduction APBDG0L031K0FA is a PC platform panel computer designed for use in rolling stock. In following text the device will be referred only as ‘computer’. Computer APBDG0L031K0FA contains the Master processor module with ® ™ Intel Atom processor (Master CPU hereinafter) and an Auxiliary processor module with processor Cortex (Aux CPU hereinafter), which ensures the supplementary terminal functions. -
Page 6: Technical Parameters
APBDG0L031K0FA 2. Technical parameters Module MSC Q7-BT-15-20B2I ® ™ Intel Atom E3815, Single core, 1.46 GHz 2 GB, DDR3L SDRAM FLASH memory 4 GB SATA SLC Flash *) RTC backup Panasonic BR2477/CHCE Lithium battery Battery lifetime 5 years Note *) Memory is fixed part of module. - Page 7 APBDG0L031K0FA Ethernet Quantity Operation indication LED (LNK and ACT) Galvanic separation Insulation strength 1000 V AC /1 minute Data transmission rate 10/100 Mbps Connection point M12 connector according to IEC 61375-3-4 ed.1 HARTING PushPull Recommended cabling STP CAT6 Maximum segment length...
- Page 8 APBDG0L031K0FA Dangerous Unit overall mass of plastics Max. 513 g materials Included mass of self-extinguishing Max. 513 g plastics Device does not contain PUR, PVC, Asbestos Device conforms 2011/65/EU (ROHS) 1907/2006EU (REACH) -30 °C to 70 °C Temperatures Operating temperature range -40 °C to 80 °C...
-
Page 9: Dimensions
S/N: ABCD MAC X11: 00-00-00-00-00-00 AUX FW: APP 0.00 / LDR 0.00 POWER: 16.8 V to 45 V DC / 1.5 A WEIGHT: 3,86 kg TEST: OK-MU HiPot: HiPot - OK DATE: 4.12.2015 Fig. 1 - APBDG0L031K0FA dimensions 9/35 apbdg0l031k0fa_g_en_101... -
Page 10: Recommended Drawing Symbol
APBDG0L031K0FA 2.2. Recommended drawing symbol Following drawing symbol recommended panel computer APBDG0L031K0FA. APBDA0L031K0FA AUDIO D-sub DE-9 ETH1 Type A Fig. 2 - APBDG0L031K0FA drawing symbol apbdg0l031k0fa_g_en_101 10/35... -
Page 11: Block Diagram
APBDG0L031K0FA 2.3. Block diagram 2x USB AUDIO Codec + amplifier Master CPU 2 GB RAM 4 GB FLASH Buzzer Touch Auxiliary CPU panel Temperature sensor Power supplies ETH1 Fig. 3 - APBDG0L031K0FA block diagram 11/35 apbdg0l031k0fa_g_en_101... -
Page 12: Product Marking
APBDG0L031K0FA 3. Product marking APBDG0L031K0FA is fitted with producer type label. Location of labels, see Fig. 4 - Location of labels on computer cover. TYPE: APBDG0L031K0FA S/N: ABCD MAC X11: 00-00-00-00-00-00 AUX FW: APP 0.00 / LDR 0.00 POWER: 16.8 V to 45 V DC / 1.5 A... -
Page 13: Producer Type Label
APBDG0L031K0FA 3.1. Producer type label The computer has a producer type label attached to its rear side. Data located on type label are listed in the table below, for example of label design see Fig. 5 - Type label example. -
Page 14: Conformity Assessment
APBDG0L031K0FA 4. Conformity assessment The equipment meets the requirements of NV616/2006 Czech governmental decree. The compliance assessment with NV616/2006 has been performed in accordance with harmonized standard EN 50121-3-2:2006. Tested in accordance Type of test Classification with standard EN 55011:2009... -
Page 15: Other Tests
APBDG0L031K0FA 4.1. Other tests This product was assessed and approved for use in railway applications according to standards: Tested in accordance Type of test Classification with standard Railway applications – Electronic EN 50155:2007 Complies equipment used on rolling stock Railway applications – Electromagnetic... -
Page 16: Power Supply
APBDG0L031K0FA 5. Power supply Computer APBDG0L031K0FA can be powered only by DC power supply. Power supply voltage is connected to terminals Vcc and GND of PWR connector. Terminal SB is used for computer turning on and off, terminal PE for connection of computer chassis. -
Page 17: Power Supply Connector Pinout
APBDG0L031K0FA 5.1. Power supply connector pinout APBDG0L031K0FA computer equipped with 4-pin connector WAGO 769-634 type labeled as PWR. It’s used as power supply connector. Signal Signal type connector Power supply pinout Computer chassis Power supply, Ground Turning the computer ON 5.2. - Page 18 APBDG0L031K0FA Correct To prevent the data damage the computer must be shut down only by SB shut down terminal. First, it’s necessary to disconnect the supply voltage from SB terminal, thereby is initiated a correct process of systemic termination of application and operating system run.
- Page 19 APBDG0L031K0FA The incorrect unit shut down occurs always when SB signal is deactivated within the time shorter than ton since computer is started (see the figure below). HW state SW state toff2 Fig. 10 - Incorrect shut down Signal SB can be connected directly with device Vcc terminal. In this case operating system must be designed so that instant shutting down could not cause damage the data.
-
Page 20: Internal Processor Modules
APBDG0L031K0FA 6. Internal processor modules 6.1. Master processor module APBDG0L031K0FA computer contains as Master CPU the MSC Q7-BT-15- 20B2I core. ® Atom™ E3815 Single-core. Core Core is base on processor Intel For more details see the MSC Q7-BT module datasheet on manufacturer's website (see Related documentation). -
Page 21: Communication Lines And Peripherals
Ethernet USB Audio Piezo buzzer Touch panel Backup battery 7.1. Ethernet APBDG0L031K0FA computer is equipped with an Ethernet interface with M12-4pin type connector. HARTING PushPull M12 system compatible. APBDG0L031K0FA TYPE: S/N: ABCD MAC X11:... - Page 22 APBDG0L031K0FA Line state Activity of Ethernet line is indicated by LEDs (LNK and ACT) on rear panel. The indication LNK LED indicates attaching of network cable, while ACT LED indicates transmitting or receiving of data. On next figure is presented a front view on Ethernet socket.
-
Page 23: Usb
APBDG0L031K0FA 7.2. USB APBDG0L031K0FA contains two USB host lines with USB type A connectors. All USB connectors are located on the rear cover of APBDG0L031K0FA computer. APBDG0L031K0FA TYPE: S/N: ABCD MAC X11: 00-00-00-00-00-00 AUX FW: APP 0.00 / LDR 0.00 POWER: 16.8 V to 45 V DC / 1.5 A... -
Page 24: Audio
APBDG0L031K0FA 7.3. Audio APBDG0L031K0FA is equipped with stereo audio output. For audio output is used the Cirrus Logic codec CS4207 which meets the HDA standard. TYPE: APBDG0L031K0FA S/N: ABCD MAC X11: 00-00-00-00-00-00 AUX FW: APP 0.00 / LDR 0.00 POWER: 16.8 V to 45 V DC / 1.5 A... -
Page 25: Piezo Buzzer
– Service manual (file apbxxx_mr_en_xxx.pdf). 7.4.1 External piezo buzzer output APBDG0L031K0FA panel computer is equipped with external piezo buzzer output. This output is led out on connector on back cover of computer. On this output the amplified internal buzzer signal is available. -
Page 26: Touch Panel
16 independent touches, including standard motion gestures (depends on used OS). 7.6. Backup battery APBDG0L031K0FA computer is equipped with RTC backup battery, including a removable cover for its easy replacement. For description of the procedure of the battery change see the Related documentation –... -
Page 27: Mounting
8. Mounting 8.1. Mounting instructions Panel computer APBDG0L031K0FA can be mounted into any position. To ensure proper cooling and access to the terminal we recommend to keep a free space of minimum 70 mm sidewise and 100 mm from rear side from surrounding equipment. - Page 28 APBDG0L031K0FA Fig. 20 - Location of mounting holes A - A SCALE 2:1 Fig. 21 - Profile of mounting holes apbdg0l031k0fa_g_en_101 28/35...
-
Page 29: Installation Rules
APBDG0L031K0FA +1,0 282,0 -0,0 4 × D6 140,5 140,5 Fig. 22 - Mounting apertures 8.3. Installation rules PE terminal of power supply connector must be connected with local installation earth terminal. Minimum cross-section of supplying wires must be at least 0.82 mm All cabling must be carefully tied by cable ties to avoid the excessive connector pulling or prying. -
Page 30: Ordering Information, Product Part List
APBDG0L031K0FA 9. Ordering information, product part list Unit complete, see chapter 9.1 – Completion Panel APBDG0L031K0FA computer 9.1. Completion APBDG0L031K0FA Part Quantity Panel computer Routine testing protocol Insulation testing protocol Certificate of product quality and completeness Power supply connector counterpart 9.2. -
Page 31: Packaging
APBDG0L031K0FA 10. Packaging Front panel Display area including front panel is protected by plastic foil against scratches protection and dirt. This foil is recommended to stay on the device during mounting to the vehicle and must be removed before using the device. -
Page 32: Storage
APBDG0L031K0FA 11. Storage To prevent any damage to the device please keep the following rules. Packed The computer in the original box must be stored only under environmental computer conditions defined in technical parameters. The device must be kept away from water, oil or any other liquid which can damage the packing. -
Page 33: Maintenance
APBDG0L031K0FA 12. Maintenance Warning Maintenance mentioned below can be performed only by manufacturer or authorized service. 12.1. Backup battery replacement Backup The backup battery lifetime is limited. Its replacement is necessary at least battery every five years. If special panel computer usage conditions are comply with, the service interval can be prolonged according to chart on Fig. -
Page 34: Cleaning
APBDG0L031K0FA 12.2. Cleaning According to cleanliness of the environment, where the computer is installed, it is necessary to remove dust and dirt from the panel computer. Cleaning intervals have to be planned by the vehicle designer. According to the dust and dirt contamination level, there are cleaning ways as... -
Page 35: Waste Disposal
APBDG0L031K0FA 13. Waste disposal Electronics The disposal of electronic equipment is subject to the regulations on handling disposal electrical waste. The equipment must not be disposed of in common public waste. It must be delivered to places specified for that purpose and recycled.
Need help?
Do you have a question about the APBDG0L031K0FA and is the answer not in the manual?
Questions and answers