Advertisement
Quick Links
Advertisement
Summary of Contents for Talet Equipment RBV V50
- Page 1 V50 Rotary Brush Cutter-Standard Deck (RBV) (Standard and High Flow Models) Model Number Serial Number Maximum Flow Rate Serial Number 128311, 130058-135126 and 136598 Manufacture Date 01/22/18 – 06/24/18 Phone: 320-393-7080 10/05/10 Revised 01/22/18...
-
Page 2: Initial Use
Features of Virnig Mfg. Inc. V50 Rotary Brush Cutter-Standard Deck include: • 4” diameter maximum cutting capacity. • Four hydraulic motor options with standard flow rates covering 14-25 gpm and high flow rates covering 25-42 gpm. • Standard dual hydraulic pressure relief valves with dynamic braking. •... -
Page 3: Operation
Operation • Always follow safety and operating information in this manual. • Always follow all safety and operating instructions of skid loader. • Never remove material deflectors or safety labels. Make sure all safety labels are in place. Refer to this manual for label locations. •... - Page 4 Operation (cont.) • Keep bystanders back 200 feet at all times. Do not operate near buildings, traffic, pets or livestock. • Never allow riders on the V50 Rotary Brush Cutter-Standard Deck, even when blades are not rotating. • Check that all bolts are tight and that no parts are damaged. Make sure blades swing freely.
- Page 5 Operation (cont.) • The V50 Rotary Brush Cutter-Standard Deck High Flow will rotate in only one direction. The operator should verify the direction the cutter is spinning. When looking top down on the deck, the Industrial Rotary Cutter should spin in a counter clockwise direction. If cutter does not spin in the proper direction, please contact Virnig Mfg Inc.
-
Page 6: Maintenance
Maintenance *Before each use and after every 10 hours of operation • Make sure all safety labels are in place, look in this manual for locations. • Check lubricant level in the V50 Rotary Brush Cutter-Standard Deck bearing adapter (spindle). Remove the plug on the side of the bearing housing, just above the mount flange with bolts holding it to the cutter deck. - Page 7 Maintenance (cont.) • The pressure relief valves are preset and require no maintenance or adjustment. Unauthorized adjustment may cause damage to the motor or change the rate the blades slow to a stop. Please call Virnig Mfg. Inc. with any questions or problems regarding the pressure relief valves. •...
- Page 8 Blade Carrier Removal and Installation • Make sure hydraulics are disconnected from machine and deck is properly supported as you will need access to the bottom of the deck. The V50 Rotary Brush Cutter-Standard Deck is very heavy and steps need to be taken to make sure the deck is stable and secure before making any repairs.
- Page 9 Labels on V50 Rotary Brush Cutter-Standard Deck Attachment 7389PP – RBV DANGER HAZARD LABEL This label has several important instructions for safe operation regarding flying object hazards and cutting hazards. 7388PP – RBV DANGER STAY CLEAR LABEL All bystanders must stay clear during operation. 7387PP –...
- Page 10 Labels on V50 Rotary Brush Cutter-Standard Deck Attachment (cont.) 7386PP – RBV MAIN WARNING LABEL This label has several important instructions that must be followed for safe operation of this attachment. 7489PP – 18 GPM MAX LABEL 7490PP – 25 GPM MAX LABEL 7794PP –...
- Page 11 V50 Rotary Brush Cutter-Standard Deck (RBV) Label Parts List ITEM PART NO. QTY DESCRIPTON 7386PP RBV MAIN WARNING LABEL 7387PP RBV LIFT LIMIT WARNING LABEL 7388PP RBV DANGER STAY CLEAR LABEL 7389PP RBV DANGER HAZARD LABEL 7489PP 18 GPM MAX LABEL 7490PP 25 GPM MAX LABEL 7794PP...
- Page 12 V50 Rotary Brush Cutter-Standard Deck (RBV) Parts List ITEM PART NO. QTY DESCRIPTION 1003PP 1/2"-13 REVERSE LOCK NUT 1008PP 5/8"-11 TOP LOCK NUT 1083PP 3/8" USS FLAT WASHER 5148PP 1/2" USS FLAT WASHER 5226PP 1/2"-13 X 1 1/2" LG HHCS 6140PP 3/8"-16 TOP LOCK FLANGE NUT 7249PP...
-
Page 13: Bolt Torque Chart
Bolt Torque Chart GRADE 5 GRADE 8 SHCS* SIZE COARSE FINE COARSE FINE COARSE FINE 1/4" 5/16" 3/8" 7/16" 1/2" 9/16" 5/8" 3/4" *SHCS—Socket Head Cap Screw Values are in ft.-lb. and are recommended unless otherwise noted. Access Cover Assembly... - Page 14 Skid Shoe and Chain Assembly Lift Limit Chain Assembly...
- Page 15 Drive and Blade Assembly Torque per Spec Torque to 425-450 Ft-Lb Torque per Spec Note: Apply a thread locking compound to Item #26 prior to assembly. Blade Carrier Assembly ITEM PART NO. QTY DESCRIPTION 8569VP LOWER BLADE CARRIER PLATE 8716VP 60"...
- Page 16 Standard Flow Hydraulic Component Assembly ITEM PART NO. QTY DESCRIPTION 33 10684PP 5/16"-18 X 3 1/4" LG HHCS 34 6719PP 1/2" -13 X 1 1/2" LG SHCS 35 6734PP COUPLER FEMALE 12FB 36 6735PP COUPLER MALE 12FB 37 9028PP ADAPTER 12MJ TO 10 MB 38 7672PP 5/16"-18 TOP LOCK FLANGE NUT 39 11020PP...
- Page 17 High Flow Hydraulic Component Assembly ITEM PART NO. QTY DESCRIPTION 45 10384PP MANIFOLD CROSS PORT RELIEF 46 10557VP IRC MANIFOLD GUARD LOWER 47 10559VW IRC MANIFOLD GUARD WELDMENT 48 10560PP 3/8"-16 X 6" LG HHCS 49 6140PP 3/8"-16 TOP LOCK FLANGE NUT 50 10561PP 3/18-16 X 4 1/4"...
- Page 18 High Flow Hydraulic Component Assembly (cont.) High Flow Bearing Adapter (spindle) oil capacity is 14 fluid ounces.
- Page 19 Optional Roller Assembly (BCR) ITEM PART NO. QTY DESCRIPTION 1008PP 5/8"-11 TOP LOCK NUT 7431VW 60" BRUSH CUTTER ROLLER WDT 7381VW 66" BRUSH CUTTER ROLLER WDT 7277VW 72" BRUSH CUTTER ROLLER WDT 7415VW 78" BRUSH CUTTER ROLLER WDT 7719PP 5/8"-11 X 2" LG HHCS 7773PP 2"...
- Page 20 Optional Front Caster Assembly (BCC) ITEM PART NO. QTY DESCRIPTION 1005PP 7/16"-14 REVERSE LOCK NUT 1008PP 5/8"-11 TOP LOCK NUT 1034PP 1/4"-28 STRAIGHT GREASE ZERK 1046PP 7/16"-14 X 2 3/4" LG HHCS 1094PP 1 1/4" X 10GA MACH BUSHING 1111PP 1 1/4"...
Need help?
Do you have a question about the RBV V50 and is the answer not in the manual?
Questions and answers