Table of Contents
Advertisement
Quick Links
2-Channels Intelligent Charger
For LiPo/LiFe/LiHv/Lilon/NiMH/NiCd/Pb batteries
Include Intelligent power allocation and average power allocation.
Single channel AC Power: Max 100W in intelligent allocation mode
• Charge Power: DC 200W / AC 100W
• Charge Current: MAX.10A*2
Thanks for purchasing GT Power X2mini Charger. This is a charger with built in
microprocessor and newest program. This charger can support 2 channels
charging, can charge 2 di erent battery types at the same time. This charger
with fashion design, easy to operate. Please read the manual completely and
carefully before using.
200
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for GT POWER X2mini
Summary of Contents for GT POWER X2mini
- Page 1 • Charge Power: DC 200W / AC 100W • Charge Current: MAX.10A*2 Thanks for purchasing GT Power X2mini Charger. This is a charger with built in microprocessor and newest program. This charger can support 2 channels charging, can charge 2 di erent battery types at the same time. This charger with fashion design, easy to operate.
-
Page 2: Table Of Contents
Contents 1.Speci cations..............2 2.The exterior appearance of the unit . -
Page 3: Speci Cations
1. Speci cations Input Voltage AC.100-240V DC.19-26V Charge Current 0.1-10.0A*2 Charge Power AC.Max.100W DC.Max.100W*2 Balance Current 500mA Balance Precision ±0.01V Charging Capability LiPo/LiFe/LiIon/LiHv: 1-4cells NiMH/NiCd: 1-8cells Pb: 2-14V Weight 554g Dimensions 137.5*141.5*55.5mm... -
Page 4: The Exterior Appearance Of The Unit
2.The exterior appearance of the unit Air vent Screen The first channel The second channel indicate light indicate light ENTER/START key CHANNEL/SELECT key INC key STOP key DEC key Balance port Battery connection interface Direct current input:19-26V AC input:100-240V... -
Page 5: Warnings And Safety Notes
3. Warnings and safety notes · Never leave the charger unsupervised when it is connected to power.If any malfunction happens, terminate the program immediately and refer to the operation manual for the right operation. · Keep the unit away from dust, damp, rain, heat, direct sunshine and vibration. Do not drop it. - Page 6 · The charger and the battery to be charged should be set up on a heat-resistant, non-flammable and non-conductive surface. · Please ensure that the fan and vents of the charger are not blocked by the surface that it is placed on. ·...
-
Page 7: Program Ow Chart
4. Program ow chart Start Battery Type LiPo BALANCE LiPo FAST Enter Select LiPo - > 10.0A 7.4V(2S) 10.0A 7.4V(2S) Start Battery Type LiIo BALANCE LiIo FAST Enter Select LiIo - > 10.0A 7.4V(2S) 10.0A 7.4V(2S) Start LiHV BALANCE LiHV FAST Battery Type Enter 10.0A 7.4V(2S) -
Page 8: Charging Current Setting
5. Charging current setting You have to know the battery allowable maximum charge current before charging.Charge current exceeds the allowable maximum charge current may cause damage to battery and it is possible to lead a fire and explosion of battery when charging. We usually use C value to mark battery charging/discharging capability.The battery allowable maximum charging current is calculated by multiply C value by battery capacity . -
Page 9: Lithium Battery (Lilo/Lipo/Life/Lihv) Mode Instruction
Under DC input mode, each channel can charge under maximum power 100W, improve charging efficiency and shorten charging time. 7. Lithium Battery (LiLo/LiPo/LiFe/LiHv) Mode Instruction Charging Lithium battery at balance mode This is for balancing the voltages of Lithium batteries of the battery pack to be charged. Inner system will monitor each cell’s voltage and restraint each cell’s current to fulfill balance charging. - Page 10 Press STOP key Back to the last interface, then press ENTER key to the next menu. LiPo BALANCE Choose the right program, press ENTER key to choose 9.9A 14.8V(4S) balance charging mode or fast charging mode enter into next program, back press STOP key. Shortly press ENTER key to current setting.
-
Page 11: Cell Meter Test Program
9. Cell meter test program This charger with built-in high-bit micro-processor, can be User Program used as a cell meter.It can show the voltage of each cells, the Cell Meter total battery pack voltage and the highest/lowest voltage. Start Choose the cell meter program interface, press START to Enter enter. -
Page 12: Load Data Setting
11. Load data setting This program calls back the data that was stored at 'Save PROGAM SELECT Data' program. To load the data, press Start/Enter key once Load date to blink the data number field and select the number using INC or DEC key then press Start/Enter key for more than 3 Start Enter... - Page 13 Safety time setting If you turn on safety timer, safety timer will start timing Safety Timer when charging.If system fault or system can’t identify 300min battery capacity already full, this safety time set can stop battery being over charged. The safety time should not shorter than the time battery fully charged, usually from 10min to 720min.
-
Page 14: Warning And Error Messages
Firmware upgrade Firmware Upgrade - > Press ENTER key to do firmware upgrade Power Allocation Power Mode Under AC power supply, you can choose the power Dynamic Mode allocation mode, intelligent allocation or average allocation. First priority: intelligent allocation. Dynamic Mode: average allocation. 13. -
Page 15: Warranty And Service
This warranty does not cover the damage due to wear, overloading, incompetent handling or using of incorrect accessories. CONFORMITY DECLARATION G.T.POWER X2mini satisfies all relevant and mandatory CE directives and FCC Part 15 Subpart B. The product has been tested to meet the following technical standards: Test Standards...
Need help?
Do you have a question about the X2mini and is the answer not in the manual?
Questions and answers