Summary of Contents for Kimo 7302
- Page 1 KIMO INSTRUCTION MANUAL 7302 20V Max Cordless Angle Grinder www.kimotool.com If you have questions or comments, contact us. Kimo-support@kimotools.com...
-
Page 2: Work Area
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY KIMO TOOL, EMAIL US AT: Kimo-support@kimotools.com General Safty Rules - For All Tool WARNING! Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. - Page 3 tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools may result in serious personal injury. Dress properly. Do not wear loose clothing or jewelry. • Contain long hair. Keep your hair, clothing, and gloves away from moving parts.
- Page 4 that cannot be controlled with the switch is dangerous and must be repaired. Store idle tools out of reach of children and other • untrained persons. Tools are dangerous in the hands of untrained users. Maintain tools with care. Keep cutting tools sharp and clean. •...
- Page 5 ADDITIONAL SPECIFIC SAFETY INSTRUCTIONS Always use proper guard with grinding wheel. A guard • protects operator from broken wheel fragments and wheel contact. Accessories must be rated for at least the speed recom- • mended on the tool warning label. Wheels and other accessories running over rated speed can fly apart and cause injury.
- Page 6 Always use side handle. Tighten the handle securely. The side • handle should always be used to maintain control of the tool at all times. Never cut into area that may contain electrical wiring or • piping. Serious injury may result. Clean out your tool often, especially after heavy use.
-
Page 7: Tool Components
4. Wheel Guard 9. Battery Slide Button 5. Wheels ACCESSORIES 1. Cordless Angel Grinder 5. 1-Hour Fast Charger 2. Two Cutting Wheels 6. Side Handle 3. One Grinding Wheels 7. Lock Nut Wrench 4. KIMO Battery 8. KIMO Carrying Bag... -
Page 8: Specifications
SPECIFICATIONS Model 7302 Wheel Diameter 4-1/2”(115 mm) Rated Speed/No Load Speed 6700 Revolutions/Minute Rated Battery Voltage 3.9 lbs Weight (Bare Tool) Weight (Tool + Battery) 5.3 lbs SLIDER SWITCH WARNING: Before connecting the tool to a power supply, make sure the slider switch(2) is in the off position by pressing the rear part of the switch and releasing. -
Page 9: Spindle Lock
SPINDLE LOCK The spindle lock is provided to prevent the spindle from rotating when installing or removing wheels. Operate the spindle lock only when the tool is turned off, unplugged from the power supply, and has come to a complete stop. Do not engage the spindle lock while the tool is operating because damage to the tool will result. -
Page 10: Installation
INSTALLATION INSTALLING SIDE HANDLE WARNING: Always make sure that the side handle is installed securely before operation. INSTALLATION - Screw the side handle securely. According to your using habit, the handle could be installed on the left or right side of the tool as shown in the figure. - Page 11 1. Wheel Guard 2. Bearing Box 3. Screw INSTALLING OR REMOVING WHEEL WARNING: Always remove battery pack before changing or removing • accessories. Always use supplied guard when depressed center grinding • wheel/Multi-disc is on tool. Wheel can shatter during use and guard helps to reduce chances of personal injury.
- Page 12 use the lock nut wrench and securely tighten clockwise. WARNING: Only actuate the shaft lock when the spindle is not moving. 1. Lock Nut Wrench 2. Shaft Lock G. To remove wheel, remove the battery pack and reverse the procedure.
-
Page 13: Operation
OPERATION WARNING: It should never be necessary to force the tool. The weight of the • tool applies adequate pressure. Forcing and excessive pressure could cause dangerous wheel breakage. ALWAYS replace wheel if tool is dropped while grinding. • NEVER bang or hit grinding disc or wheel onto work. •... -
Page 14: Maintenance
break-in period with a new wheel, do not work the grinder in the B direction or it will cut into the workpiece. Once the edge of the wheel has been rounded off by use, the wheel may be worked in both A and B direction. - Page 15 To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by KIMO Authorized or Factory Service Centers, always using KIMO replacement parts.
-
Page 16: Battery Instructions
BATTERY INSTRUCTIONS CAUTION: Only use genuine KIMO batteries. Use of non-genuine KIMO batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury and damage. It will also void the KIMO warranty for the KIMO tool and charger. - Page 17 INDICATING THE REMAINING BATTERY CAPACITY Battery Pack LED Indicator KIMO battery packs include a fuel gauge which consists of four LED lights that indicate the level of charge remaining in the battery pack.The fuel gauge is an indication of approximate levels of charge remaining in the battery pack according to the following indicators: NOTE: 1.
- Page 18 Charging Indicator NOTE: It takes 1-2 hours to full charge KIMO battery.
-
Page 19: Warranty
WARRANTY Every KIMO power tool is warranted to the original purchaser only to be free from defects in material and workmanship. Subject to certain exceptions, KIMO will replace any part on an electric power tool that is defective in material or workmanship for a period of 2 years after the date of purchase unless otherwise noted. - Page 20 EXTENDED WARRANTY REGISTRATION Dear Customer, Thank you very much for choosing KIMO. At KIMO, customer satisfaction is our highest priority. In order to provide the best services, we would like to offer you an extra 6-month limited warranty. Below is the free registration process.
Need help?
Do you have a question about the 7302 and is the answer not in the manual?
Questions and answers