Table of Contents
Advertisement
Quick Links
IVIE Enterprises
www.ivie-ent.com
Ph:(918)254-5161 or (888)262-5161 Fax:(918)250-4807
Operator's
3DS
Manual
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read this
book prior to operating or attempting any service or maintenance procedure to your ALTO machine could
result in injury to you or to other personnel; damage to the machine or to other property could occur as
well. You must have training in the operation of this machine before using it. If you cannot read English,
have this manual explained fully before attempting to operate this machine.
Si Ud. o sus operadores no pueden leer el Inglés, se hagan explicar este manual completamente antes
de tratar el manejo o servicio de esta máquina.
All directions given in this book are as seen from the operator's position at the rear of the machine.
For new books write to: ALTO U.S. Inc., 2100 Highway 265, Springdale, Arkansas 72764.
Form No. 74845A
3/01
AMERICAN SANDERS TECHNOLOGY
Printed in the U.S.A.
Advertisement
Table of Contents
Related Manuals for Alto 3DS
Summary of Contents for Alto 3DS
- Page 1 IVIE Enterprises www.ivie-ent.com Ph:(918)254-5161 or (888)262-5161 Fax:(918)250-4807 Operator's Manual READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your ALTO machine could result in injury to you or to other personnel;...
-
Page 2: Table Of Contents
Assembly Parts List #1 ... 19 Assembly Drawing #2 ... 20 Assembly Parts List #2 ... 21 Electrical Schematic ... 22 www.ivie-ent.com Page 2 Contents of this Book IVIE Enterprises Ph:(918)254-5161 or (888)262-5161 Fax:(918)250-4807 AMERICAN SANDERS TECHNOLOGY Operator’s Manual - 3DS... -
Page 3: Operator Safety Instructions
Always use a three-wire electrical system connected to the electrical ground. For maximum protection against electric shock, use a circuit that is protected by a ground fault interrupter. Consult your electrical contractor. AMERICAN SANDERS TECHNOLOGY Operator’s Manual - 3DS AVERTISSEMENT ADVERTENCIA... -
Page 4: Explanation Of Hazard Symbols
This symbol of a person wearing goggles warns of injuries to eyes. This symbol of a man lifting shows that injury could occur without proper lifting procedures. Page 4 Moving parts Eye Protection Read Owner’s Manual Explanation of Hazard Symbols AMERICAN SANDERS TECHNOLOGY Operator’s Manual - 3DS Heavy Object... -
Page 5: Introduction And Machine Specifications
Introduction & Machine Specifications The 3DS is a machine designed primarily for fine finish sanding of hardwood floors. The finish sanding process results in a smoother and flatter floor and assists in removing imperfections created during the drum or belt sanding process. -
Page 6: Instructions On Connection To Power Supply 230 Volt
12 AWG or 2.5mm WARNING:To avoid motor burnout, if you use WARNING:To avoid electrical shock, do not cut, AMERICAN SANDERS TECHNOLOGY Operator’s Manual - 3DS NEMA L6-20P Figure 1 this machine with an AC three-con- ductor electrical system connected to the electrical ground. -
Page 7: Machine Breakdown/Transportation
4” diameter wheels contact the floor. With steady downward pressure on the handle the machine can be pushed to the desired location. (see Figure 5) AMERICAN SANDERS TECHNOLOGY Operator’s Manual - 3DS Figure 2 Ü Ü... - Page 8 “ON” position. The vacuum switch should remain in the “ON” position. (See Figure 11 below) Ü Ü Page 8 Figure 11 AMERICAN SANDERS TECHNOLOGY Operator’s Manual - 3DS Figure 6 Figure 7 Ü Figure 8 Ü Figure 9...
-
Page 9: Machine Set-Up
Place your foot on the tilt assist strap and ease the sanding unit to the floor. Connect the vacuum hose to the sanding unit and vacuum. Connect the power cord to the electric box. AMERICAN SANDERS TECHNOLOGY Operator’s Manual - 3DS Figure 12 Ü Figure 13 Ü... -
Page 10: Operating Instructions
The operator must be moving the machine when the machine is running. The operator may move the machine in any direction when sanding the floor. Page 10 Manual AMERICAN SANDERS TECHNOLOGY Operator’s Manual - 3DS Figure 16 Auto Ü Start Stop... -
Page 11: Maintenance
“velcro” on the sanding pads should be checked for any frays, wear, or damage. Service Maintenance: The 3DS Sander must be serviced after every 600 hours of use. Contact an authorized Alto Service Center/Person for service. (The Service Centers are listed on the inside back cover of the Operator’s...