GARDENJACK GBC26C Original Instructions Manual

Hide thumbs

Table Of Contents

Quick Links

Download this manual

Brush Cutter

O RIGINAL INSTRUCTIONS

GBC26C

Table of Contents

Summary of Contents for GARDENJACK GBC26C

Page 1 Brush Cutter O RIGINAL INSTRUCTIONS GBC26C...
Page 2: Table Of Contents
Brush Cutter Contents Contents Page........1 Machine Information.......2 Machine Diagram........3 Preparation & Use.......4/5 Mounting Spool & Blade....6/7/8 Fuel & Refuelling......9/10/11 Using The Cutting Tool....12/13/14 Maintenance.......15/16/17 Cleaning & Transport......18 Technical Data........19/20 Declaration...........21 GBC26C...
Page 3: Machine Information
D type handle D type handle Holder Start/Stop Switch Throttle Lever Throttle Lock Starter Handle Fuel Tank Spark Plug Choke Oil bubble Exhaust System Locking Disc Hex Screw Lock Washer Retaining Disc Spool Cutter Blade Protection Brush Cutter Blade GBC26C GBC26C...
Page 4: Machine Diagram
Brush Cutter Machine Diagram GBC26C...
Page 5: Preparation & Use
The max trunk diameter is 2 cm. · This machine is only intended for cutting grass, weeds, bushes, undergrowth. It should not be used for any other purpose such as digging or hedge cutting. GBC26C...
Page 6 Hint: For space-saving transport and storing, dismount the D type angle 3. Fasten the throttle cable (9) with the included clamps on the tube. By doing this, the cable cannot be damaged if accidently jammed. 4. Insert both tube into each other and lock them with the locking screw. GBC26C...
Page 7 ·Hang the machine on the carabiner hook. The cutting tool must evenly touch the ground when working in comfortable working position. If necessary, loosen the suspension eye (10) by using the hex key, move it back or forth & re-position the suspension eye. GBC26C...
Page 8 1. Insert the toothed locking disc on the thread of the cutting tool holder (1). 2. Place the brush cutter blade on the tool holder and then the lock washer (C). Make sure the lock washer is placed with the convex side up! GBC26C...
Page 9 7. Tighten the hex nut with the included combination wrench only hand tight and hold the hex key firmly in this position while tightening the hex nut. GBC26C...
Page 10 Mixing Bottle For mixing the fuel and the two stroke oil only use the provided mixing bottle. First fill the fuel into the bottle and then the oil. Thoroughly shake the mixture. GBC26C...
Page 11 10. Pull the starter handle vigorously 4 to 5 times. 11. Pull the starter handle quickly and forcefully up to the cable end several times, until the engine starts. Please note that the engine will start at half acceleration and with rotating cutting tool. GBC26C...
Page 12 · Always ensure a proper idle running of the engine so that the cutting tool will no longer rotate, when the throttle is pressed. · Always use the highest speed for work, this way you will achieve the best cutting result. GBC26C...
Page 13 In this case, it might happen that the plastic thread disappeared into the string spool housing and the automatic trimming thread feed will not work anymore. GBC26C...
Page 14 5. Guide both thread ends through the metal eyelets in the spool housing and re-attach the thread holder into the cover. Make sure the parts lock audibly and visibly into each other. 6. Mount the spool on the tool holder again. GBC26C...
Page 15 This way, the objects to be cut will be shredded. ATTENTION: Always be careful, when using this working technique, because the further away the cutting tool is from the ground, the higher is the risk that objects to be cut and particles will be hurled sideways. GBC26C...
Page 16: Maintenance
Do not touch the exhaust system. There is risk of burns! Before working on the machine (transport, mounting, dismounting, cleaning and servicing) and if not in use, remove the spark plug cap or disconnect the gear shaft from the motor unit! GBC26C...
Page 17 · Make sure not to overfill the gear housing. · The brush cutter blade must be sharpened by a professional only. Improperly sharpened or blunt cutting edges may cause the blade to break or torn. GBC26C...
Page 18 Clean the electrodes with a wire brush and reset the gap to approx. 0.65 mm as necessary. GBC26C...
Page 19: Cleaning & Transport
Do not use cleaning agents, solvents or spiky objects to clean the machine. Transport Always turn the machine off when carrying or transporting it. Do not carry or transport the machine with running cutting tool! Always carry the unit with the attachments facing backwards. GBC26C...
Page 20: Technical Data
Fuel Tank Volume 350 ml Specific Fuel Consumption at max. 370 g/kWh Engine Power Fuel Specification Ratio 40 : 1 (Gasoline : Oil) Oil Specification 2-Stroke Engine Oil Weight ( w/o Fuel, Cutting Tool and 6.1/6.0 kg Protective Hood) GBC26C...
Page 21 - Brush Cutter 6.4/6.1 m/s² - Grass Trimmer 1.5 m/s² Uncertainty K * Sound and vibration emissions may differ from the declared values during use depending on the ways in which the tool is used. GBC26C Maintaining the Motor Unit...
Page 22: Declaration
Old Heath Rd, Wolverhampton WV1 2RP Tel: 01902450470 Declares that the BRUSH CUTTER GBC26C Is in compliance with the regulations including in the directives:2006/95/EC EC DECLARATION OF COFORMITY Certificate for EC-type examination delivered by BV LCIE China, Building4,No. 518 Xin Zhuan Rd, CaoHejing Songjiang High-Tech Park, Shanghai 201612, China.