Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Generic ZBL-R620
Summary of Contents for Generic ZBL-R620
- Page 1 ZBL-R620/630 Rebar Locator Operation Manual...
-
Page 2: Table Of Contents
Operation Manual for ZBL-R620/R630 Rebar Locator Contents 1. General Introduction………………………………………………..1 1.1 Basic Working Principles …………………………………………………1 1.2 Components of ZBL-R620/R630…………………………………………1 1.3 System Interface……………………………………………………………2 2. Quick Access. …………………………………………………….2 2.1 System Connection……………………………………………………….3 2.2 Startup…………………………………………………………………….4 2.3 System Reset……………………………………………………………….4 2.4 Choosing Scan Mode………………………………………………5 2.5 Parameter Settings………………………………………………………5 2.6 Scan Operation……………………………………………………………7... -
Page 3: General Introduction
1.2 Components of ZBL-R620/R630 ZBL-R620/R630 Rebar Locator is composed of a main instrument body, a probe, a scan car (ZBL-R630 only) and signal transmission wire. The probe has direction sensitivity. The signal is strongest when the probe and the rebar directions are parallel, on the contrary the signal is weakest when the probe and rebar directions are perpendicular to each other. -
Page 4: System Interface
Operation Manual for ZBL-R620/R630 Rebar Locator 1.3 System Interface The ZBL-R620/R630 utilizes a multi-level menu management system. The menu operation interface is used to choose functions and set parameters, including: (shown in Fig. 1.2) Main Menu interface Parameter Setting interface... -
Page 5: System Connection
Operation Manual for ZBL-R620/R630 Rebar Locator the instrument by performing a number of tests in your home or office, prepare simple scenarios which mimic onsite working environments. Prepare some non-tensile rebars (use the two thick rebars to imitate the main rebar,... -
Page 6: Startup
Operation Manual for ZBL-R620/R630 Rebar Locator Place the probe in the correct direction (with the ports of the probe and Scan Car in same direction, see fig 2.3), the central hole of the probe must be aligned with the raised point on the scan car. -
Page 7: Choosing Scan Mode
Operation Manual for ZBL-R620/R630 Rebar Locator Caution: During detection process, it is advised to implement a reset operation about every ten minutes. If test data is unreliable, implement reset, then re-test. 2.4 Choosing Scan Mode ZBL-R630 Rebar Locator provides several scan and work modes, the user can select the most suitable mode according to their requirements. - Page 8 Operation Manual for ZBL-R620/R630 Rebar Locator symbols. The initial object code is 000000. When restarting, enter the parameter setting interface, the initial object code is the previously used code incremented by one character. Move the cursor to “object code”, press 【Enter】key, the curser moves to below the first digit of the code.
-
Page 9: Scan Operation
Press 【Menu】key, return to main menu. 2.6 Scan Operation ZBL-R620 provides three scan modes , ZBL-R630 provides three scan modes 1) General Test: It is the basic scan mode of R630. It accurately measures the thickness of concrete cover and the diameter of rebar, it may also judge if the component conforms to international standards. - Page 10 Operation Manual for ZBL-R620/R630 Rebar Locator In order to know the rebar’s general distribution a pre-scan may be performed on the concrete element. It is an important part when selecting scan starting point. A pre-scan allows real-time display of test information without saving data.
- Page 11 Operation Manual for ZBL-R620/R630 Rebar Locator When the rebar is detected by the probe, the system locks the thickness, in manual mode, press 【Save】key, save test result, and the save object code incremented by one. In auto save mode, the save number automatically incremented by one.
-
Page 12: Data Display
Operation Manual for ZBL-R620/R630 Rebar Locator Second scan updates scan data only, doesn’t update the rebar’s distribution image. Fig. 2.10 Fig. 2.9 The second scan operation introduced above is the normal operation, users don’t need to scan every adjacent bar, instead a cross-bar scan is performed. For the Cross-bar scan a single bar in the x-direction and a single bar in the y-direction are selected for use during a second-scan operation. - Page 13 Operation Manual for ZBL-R620/R630 Rebar Locator external storage device, personal computer or notebook computer. Make sure that the computer has already been installed with the “rebar detect data treatment software” before transmission. Use a USB cable to connect the USB port of the instrument and USB port of the computer;...
-
Page 14: Deleting Data
Operation Manual for ZBL-R620/R630 Rebar Locator 2.14) . When the progress bar is full, transmission is complete and the display will automatically return to the menu interface. 4) When transmission is complete, the transmission dialogue exits automatically and the user can open the newly created document and begin analysis. -
Page 15: No Signal
Operation Manual for ZBL-R620/R630 Rebar Locator can work after being fully charged (or while connected to the charger). If there is still no display after connecting to the charger, please check charger or call our company hotline. 3.2 No signal No signal display when scanning. -
Page 16: Appendix： General Principles Of Rebar Testing
Operation Manual for ZBL-R620/R630 Rebar Locator Table 1.3: Measuring Range of Rebar Diameter (φ6 mm ~ φ32 mm) Minimum Thickness of Concrete Maximum Thickness of Rebar Diameter Cover Concrete Cover Table 1.4: Measurement Accuracy (Bar Diameter) Unit: mm Bar Diameter ±2...
Need help?
Do you have a question about the ZBL-R620 and is the answer not in the manual?
Questions and answers