Summary of Contents for North SELEKT Series
- Page 1 OPERATING MANUAL / INSTRUCTIONS SELEKT SERIES MIG/MAG TORCH PART NUMBER: OM-101A EN ISSUE: 01-0520...
- Page 2 Tianqiao Zone, Jinan 250121, Shandong, China. Website: www.northweld.com Copyright © 2018 by: Jinan North Welding Tools Co. Ltd. ® All rights reserved. Reproduction of this User Manual, in whole or in part, without written permission of the publisher is prohib- ited.
- Page 3 Product Models: BZL, PNA, TWE, BRD MIG/MAG Manual Welding Torches Manufacturer: Jinan North Welding Tools Co. Ltd. Address: The North of 308 National Highway, Daqiao Town, Tianqiao Zone, Jinan 250121, Shandong, China. Product Identification: SELEKT MIG/MAG Manual Welding Torch Model Number SN15F-3E, SN15F-4E, SN15F-5E;...
-
Page 4: Table Of Contents
Table of Contents SECTION 1 – SAFETY INSTRUCTIONS: Read Before Using this Product ..........5 1.01 Arc Welding Hazard Symbols ..................5 1.02 Additional Installation, Operation and Maintenance Hazard Symbols ........7 1.03 Read Principal Safety Standards ................8 1.04 California Proposition 65 Warnings ................8 1.05 ELECTRIC and MAGNETIC FIELDS (EMF) Recommendations .......... -
Page 5: Section 1 - Safety Instructions: Read Before Using This Product
SAFETY INSTRUCTIONS SECTION 1 – SAFETY INSTRUCTIONS: Read Before Using this Product DANGER! – Protect yourself and others around you from possible serious injury or death. 1) Read, follow and understand this User Manual before installing, operating or servicing this Prod- uct. - Page 6 SAFETY INSTRUCTIONS ARC RAYS can injure eyes and burn • Do not weld in locations near degreasing, cleaning, or spraying opera- tions. The heat and rays of the arc can react with vapours to form highly skin toxic and irritating gases. Arc rays from the welding process pro- •...
-
Page 7: Additional Installation, Operation And Maintenance Hazard Symbols
SAFETY INSTRUCTIONS Eye protection filter shade selector numbers for welding (goggles or helmet) Welding operation Arc Amperage (Amps) Minimum Filter Shade Number Suggested ^ Filter Shade Number Less than 60 Gas Metal Arc Welding (GMAW) 60 – 160 160 – 250 Flux Cored Arc Welding (FCAW) 250 –... -
Page 8: Read Principal Safety Standards
SAFETY INSTRUCTIONS • If using lift forks to move power source, be sure forks are long FALLING EQUIPMENT can injure enough to extend beyond opposite side of power source. Use designated lifting device on power • Keep cables and Power Cords away from moving vehicles when source to lift the power source only, NOT working from an aerial location. -
Page 9: Section 2 - Warranty
JINAN NORTH WELDING TOOLS guarantees that each modified in any way except by authorized JINAN NORTH product is free from material defects and workmanship at WELDING TOOLS personnel. -
Page 10: Section 3 - Introduction
Torch system with minimal maintenance. NOTE 1: JINAN NORTH WELDING TOOLS reserves the right to change, improve or revise the specifications or design of this product without prior notice. Such updates or changes do not entitle the buyer of this Product previously sold or shipped to the corresponding changes, updates, improvements or replacement. -
Page 11: Selekt Pna Torch Specifications (Refer To Note 1)
INTRODUCTION 3.05 SELEKT PNA Torch Specifications (Refer to NOTE 1) Part Number SQTB200-3K SQTB350-3K SQTB500-3K SQTB600-3K SQTB200-4K SQTB350-4K SQTB500-4K SQTB600-4K SQTB200-5K SQTB350-5K SQTB500-5K SQTB600-5K Torch Length 3 = 3 m; 4 = 4 m; 5 = 5 m Torch Power Connector K = Panasonic Style Fitting Swan Neck Angle (°) Wire Size Range (mm) -
Page 12: Section 4 - Installation
Genuine JINAN NORTH WELDING TOOLS parts must be used for safety and performance reasons or the warranty becomes invalid. Inspect all parts for transportation damage. Do not use damaged parts. 4.03 Connecting Power Pin to Adaptor BZL Euro, TWE Euro, BRD Euro Power Pin Connector Block to Euro Adaptor 1 Disconnect power to the MIG/MAG equipment. -
Page 13: Section 5 - Operation
OPERATION SECTION 5 – OPERATION Disconnect Torch installation must be Disconnect power to Flying metal or FUMES and Shielding Moving parts Sparks, weld spatter or Improper instal- Read User done by a suitably Trained MIG/MAG equipment. Elec- dirt can injure GAS can be hazardous can cause in- hot work piece can... -
Page 14: Section 6 - Replacing Worn Consumable Parts
Genuine JINAN NORTH WELDING TOOLS parts must be used for safety and performance reasons or the warranty becomes invalid. spect all parts for transportation damage. Do not use damaged or worn parts. Before starting the MIG/MAG equipment, check the whole installation according to the manufacturer's instructions, this Manual and applicable national / state / local safety regulations. -
Page 15: Changing Twe Torch Liner
REPLACING WORN CONSUMABLE PARTS 6.04 Changing TWE Torch Liner 1 Remove nozzle, contact tip and gas diffuser then lay Torch cable straight. 2 TWE Style: Socket Head Screw – Remove using an appropriate Allen Key (Hex Key) in a counter clockwise direction. 3 Euro Style: Liner Nut –... - Page 16 TROUBLESHOOTING Description Possible Cause Corrective Action 3. Welding wire feeding A Contact tip is worn. A Replace contact tip. problems B Liner is worn / dirty. B Check the Liner; blow it out with clean, dry com- pressed air. If needed replace it. C Consumables used are not suitable for the welding C Use recommended consumables for the welding wire diameter or material.
-
Page 17: Section 8 - Routine Service And Maintenance
SPARE PARTS SECTION 8 – ROUTINE SERVICE and MAINTENANCE Disconnect Service / Mainte- Disconnect Input Power Sup- Hot parts can Turn off air compres- Welding Moving Flying Read User Improper nance must be per- ply from Welding System be- burn. Let the sor, and release air wire can parts can... -
Page 18: Section 9 - Spare Parts
SPARE PARTS SECTION 9 – SPARE PARTS Disconnect Service / Mainte- Disconnect Input Power Sup- Hot parts can Turn off air compres- Welding Moving Flying Read User Improper nance must be per- ply from Welding System be- burn. Let the sor, and release air wire can parts can... -
Page 19: Bzl Sn24F Torch Spares
SPARE PARTS Disconnect Service / Mainte- Disconnect Input Power Sup- Hot parts can Turn off air compres- Welding Moving Flying Read User Improper nance must be per- ply from Welding System be- burn. Let the sor, and release air wire can parts can metal or Manual... -
Page 20: Bzl Sn25F Torch Spares
SPARE PARTS Disconnect Service / Mainte- Disconnect Input Power Sup- Hot parts can Turn off air compres- Welding Moving Flying Read User Improper nance must be per- ply from Welding System be- burn. Let the sor, and release air wire can parts can metal or Manual... -
Page 21: Bzl Sn26F / Sn36F / Sn38F / Sn40F Torch Spares
SPARE PARTS Disconnect Service / Mainte- Disconnect Input Power Sup- Hot parts can Turn off air compres- Welding Moving Flying Read User Improper nance must be per- ply from Welding System be- burn. Let the sor, and release air wire can parts can metal or Manual... -
Page 22: Bzl Sn240F / Sn410F / Sn510F Torch Spares
SPARE PARTS Disconnect Service / Mainte- Disconnect Input Power Sup- Hot parts can Turn off air compres- Welding Moving Flying Read User Improper nance must be per- ply from Welding System be- burn. Let the sor, and release air wire can parts can metal or Manual... -
Page 23: Pna Sqbt200 Torch Spares
SPARE PARTS Disconnect Service / Mainte- Disconnect Input Power Sup- Hot parts can Turn off air compres- Welding Moving Flying Read User Improper nance must be per- ply from Welding System be- burn. Let the sor, and release air wire can parts can metal or Manual... -
Page 24: Pna Sqbt350 / Sqtb500 / Sqtb600 Torch Spares
SPARE PARTS Disconnect Service / Mainte- Disconnect Input Power Sup- Hot parts can Turn off air compres- Welding Moving Flying Read User Improper nance must be per- ply from Welding System be- burn. Let the sor, and release air wire can parts can metal or Manual... - Page 25 SPARE PARTS 9.07 PNA SQBT350 / SQTB500 / SQTB600 Torch Spares May 06, 2020 Page 25 User Manual No: OM-101A EN...
-
Page 26: Twe Snt1 Torch Spares
SPARE PARTS Disconnect Service / Mainte- Disconnect Input Power Sup- Hot parts can Turn off air compres- Welding Moving Flying Read User Improper nance must be per- ply from Welding System be- burn. Let the sor, and release air wire can parts can metal or Manual... -
Page 27: Twe Snt2 / Snt4 / Snt5 Torch Spares
SPARE PARTS Disconnect Service / Mainte- Disconnect Input Power Sup- Hot parts can Turn off air compres- Welding Moving Flying Read User Improper nance must be per- ply from Welding System be- burn. Let the sor, and release air wire can parts can metal or Manual... - Page 28 SPARE PARTS 9.09 TWE SNT2 / SNT4 / SNT5 Torch Spares May 06, 2020 Page 28 User Manual No: OM-101A EN...
-
Page 29: Brd Snq200 / Snq300 / Snq400 Torch Spares
SPARE PARTS Disconnect Service / Mainte- Disconnect Input Power Sup- Hot parts can Turn off air compres- Welding Moving Flying Read User Improper nance must be per- ply from Welding System be- burn. Let the sor, and release air wire can parts can metal or Manual... - Page 30 SPARE PARTS 9.010 BRD SNQ200 / SNQ300 / SNQ400 Torch Spares May 06, 2020 Page 30 User Manual No: OM-101A EN...
- Page 31 NOTES May 06, 2020 Page 31 User Manual No: OM-101A EN...
- Page 32 All Trademarks / Part Numbers printed in this catalogue are the property of their respective owners and are for reference purposes only. All Trademarks / Part Numbers are in no way connected or affiliated with Jinan North Welding Tools Co Ltd. Specification / Product Information / Product Appearance are subject to change without notice. Please refer to www.northweld.com for the most up-to-date data.