Table of Contents
Advertisement
Quick Links
Parts needed:
1 - Log Headboard
1 - Log Footboard (end with built-in ladder)
2 - Assembled Bunk rails (one right; one left)
1 - Bundle of 5 Slats
10 - 1 5/8" Wood Screws for slats
1 - Plywood for Upper Bunk (bottom bunky boards are optional)
8 - 1 5/8" Wood screws for Upper Bunk plywood
2 - Log Side Rails (81" Long for Single & Double Beds & 86" Long for King & Queen Beds)
16 - 6" Lag Screws and washers for Single/ Single, Double/ Double, Queen/ Queen beds
OR
12 - 6" Lag screws for Double/ Single, Queen/ Single beds
6 - 1 1/2" Diameter Log Bed Plugs (for holes to hide/cover lag screws)
5 - Support Rails (for Double/Doubles, Double/Queens, and Queen/Queen bunk beds ONLY)
see step 11 below
2 - Secondary bed rails (without notches) (for Double/Doubles, Single/Singles and Queen/Queen ONLY)
1 -
T-25 Bit (Torx bit screwdriver)
King & Queen Beds Only
• T-Support - (consists of 2 approx 7"x75" boards to be assembled)
• 8- 4" T30 screws
• 1-T30 driver bit (Torx)
CHECKING/CRACKING:
It's normal for all cedar log furniture to develop some checks in the wood. Checking occurs as a log releases moisture across or
through the annual growth rings. It does not affect the structural integrity of the wood. All logs which contain the heart of the
tree will develop lengthwise cracks or checks. The check never goes deeper than the heart.
IMPORTANT! Please read and follow the Bunk Bed Safety instructions on the last page of this instruction packet.
This product is designed to provide the safety levels of this certification when the assembly instructions are properly followed.
Completing assembly as instructed will make beds safer.
FIRESIDELODGEFURNITURE.COM | 877-568-6188
Cedar Bunk Bed Assembly Instructions
Tools Needed for Assembly:
15/16" Socket & Ratchet (or Impact Driver)
Cordless Drill with Phillips Head
Rubber Mallet if required
1
Advertisement
Table of Contents
Related Manuals for Fireside Lodge Cedar Bunk Bed
Summary of Contents for Fireside Lodge Cedar Bunk Bed
- Page 1 Cedar Bunk Bed Assembly Instructions Parts needed: Tools Needed for Assembly: 15/16” Socket & Ratchet (or Impact Driver) 1 - Log Headboard Cordless Drill with Phillips Head 1 - Log Footboard (end with built-in ladder) Rubber Mallet if required 2 - Assembled Bunk rails (one right; one left) 1 - Bundle of 5 Slats 10 - 1 5/8”...
- Page 2 Pictured is a Double/ Single Ladder Right Bed Rail Mortises READ INSTRUCTIONS COMPLETELY BEFORE BEGINNING ASSEMBLY (Note: Two people are required for assembly. One person should hold headboard, while other inserts railings.) 1. Remove all pieces from the pallet with a Phillips screw driver. 2.
- Page 3 3. Bed rails have a tenon (tapered end of the log) on each end. Insert one end, or tenon, of Log Side Rail into the 2 1/2” mortise (round hole cut into head and foot boards). The bed rails have right angles cut into them the full length of the rail. The right angles on the bed rails have a long flat-edge and a short flat-edge. 4. A correctly installed bed rail has the long flat-edge facing up. The slats for the mattress will sit on this edge.
- Page 4 7. This step applies ONLY to Single/Single, Double/Double, and Queen/Queen bunk beds a. These beds come with 2 secondary bed rails. These secondary bed rails are not quartered out (no right angle cut in). The mortises are located on the main post, above the bed rail mortises. b.
- Page 5 Important! For safety, the slats at the head and foot must be spaced so the gap to the headboard and to the footboard is 3” or less. The remaining slats may be evenly spaced between the two end slats. 12. Insert Right Hand Assembled Bunk rail (as marked on rail) into upper mortises of headboard and footboard. (All left and right rails are based upon standing at foot of bed and facing headboard).
- Page 6 15. Some tapping of support rails will be necessary to get the left assembly into mortises. Lift the Plywood over the bunk rail (right or left side) and slip it into the top bunk mattress position (It may be necessary to slip one assembled bunk rail out of the top holes to drop the plywood in).
- Page 7 Cedar Bunk Bed Safety Instructions Size of Mattress and Foundation This bed is designed to use a mattress: • Single: 74 1/2” x 38” • Double: 74 1/2” x 53” • Queen: 79 1/2” x 60” Top mattress must not exceed 10”, 3/4” foundation board supplied. Note: There must be at least 5” from mattress sleeping surface to top edge of guardrail. Replacement Parts Replacement parts, including additional guardrails, may be obtained from place of purchase.
Need help?
Do you have a question about the Cedar Bunk Bed and is the answer not in the manual?
Questions and answers