Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Vector2 EK-Quantum RE RTX 3080 D-RGB
- Page 1 EK-Quantum Vector² RE RTX 3080/3090 D-RGB GPU WATER BLOCK USER GUIDE...
- Page 2 This product is intended for installation by expert users only. Please consult with a qualified technician. Improper installation may result in damage to your equipment. EK assumes no liability whatsoever, expressed or implied, for the use of this product or its installation. The following instructions are subject to change without notice.
-
Page 3: Table Of Contents
TABLE OF CONTENTS BOX CONTENTS WATER BLOCK DIMENSIONS TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS (Nickel + Acetal) TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS (Nickel + Plexi) PREPARING THE GRAPHICS CARD REMOVING THE STOCK COOLER CLEANING THE PCB PREPARING THE WATER BLOCK FOR INSTALATION CUTTING AND PLACING THERMAL PADS APPLYING THERMAL COMPOUND ATTACHING THE WATER BLOCK... -
Page 4: Box Contents
EK-Loop Multi Allen Key (1 pc) Quantum Plug (2 pcs) Nut M2.5 (2 pcs) Terminal OR - Vector2 14x1 mm (2 pcs) Allen Key 2.5 mm (1 pc) Allen Key 2 mm (1 pc) EK-Plug Out Spludger Tool (1 pc) -
Page 5: Water Block Dimensions
WATER BLOCK DIMENSIONS 267.2 mm 123.7 mm 27 mm 95.7 mm 25.5 mm - 5 -... -
Page 6: Technical Specifications And Water Block Parts (Nickel + Acetal)
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS (Nickel + Acetal) EAN: 3831109858882 Technical Specification: -Dimensions: (LxHxW) – 267.15x134x27 mm -D-RGB (Addressable RGB) cable length: 500 mm -D-RGB LED COUNT: 32 -D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground) Position EAN Description Quantity 103944 Coldplate (Nickel) -
Page 7: Technical Specifications And Water Block Parts (Nickel + Plexi)
TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS (Nickel + Plexi) EAN: 3831109858899 Technical Specification: -Dimensions: (LxHxW) – 267.15x134x27 mm -D-RGB (Addressable RGB) cable length: 500 mm -D-RGB LED COUNT: 14 -D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground) Position EAN Description Quantity 103944 Coldplate (Nickel) -
Page 8: Preparing The Graphics Card
Do not forget to unplug all the LED and fan connectors. Pay attention to the following steps in order to install the EK-Quantum Vector2 RE RTX 3080/3090 D-RGB water block onto the graphics card. Always remove the stock cooler slowly - it might be firmly glued to the PCB via thermal pads. -
Page 9: Preparing The Water Block For Instalation
PREPARING THE WATER BLOCK FOR INSTALATION Unscrew six (6) Screws AX1 M2.5x8 as shown in the image. Remove the BACKPLATE M2.5 x 8 AX1 backplate together with six (6) Screws AX1 M2.5x8 and six (6) backplate M2.5 x 8 AX1 SCREW standoffs. - Page 10 STEP 2 The cardboard is printed in scale 1:1. Cut Thermal Pads to the size printed on the PCB cardboard. Once cut to the size, Thermal Pads should be placed on the PCB, as shown in the picture (step 2). Thermal Pads of thickness 1, 1.5 and 2 mm are included.
-
Page 11: Applying Thermal Compound
APPLYING THERMAL COMPOUND Apply the enclosed EK-TIM Ectotherm thermal grease (thermal compound) on the GPU heat spreader – IHS – as shown in the image. The layer of the thermal compound must be thin and evenly spread over the entire surface of the IHS. The excessive or uneven application of thermal grease may lead to poor performance! For this step, you will need:... - Page 12 STEP 2 Use six (6) M2.5x4 AX1 Screws and PVC washers to tighten the PCB on the water block. Tighten the screws evenly using the Phillips head screwdriver. EK recommends you start tightening SCREW M2.5x4 AX1 (6x) the screws around the GPU core first, and then continuing outward to prevent the damage to the GPU.
-
Page 13: Installing The Backplate
INSTALLING THE BACKPLATE STEP 1 Thermal Pad F – 1.0 mm (120 x 16 mm) CAUTION: You must remove the protective foil from both sides of the thermal pad before installation. 1 mm Replacement thermal pads: 120 mm Thermal Pad F 1.0mm – (120 x 16mm) EAN: 3830046996732 Thermal Pad F 1.5mm –... - Page 14 STEP 2 Thermal Pad - 120 x 16 x 1.0 mm 3080/3080Ti Apply the thermal pads onto the backplate as shown in the image. Thermal Pad - 120 x 16 x 1.5 mm F1.5 Thermal Pad - 120 x 16 x 2.0 mm F1.5 F1.5 F1.5...
-
Page 15: Attaching The Backplate
ATTACHING THE BACKPLATE BACKPLATE WITH M2.5x8 AX1 Before attaching the Active Backplate on the PCB, make sure all the Thermal Pads are placed correctly! SCREWS AND STANDOFFS STEP 1 Place the backplate with six (6)M2.5x8 AX1 Screws with Standoffs onto the PCB. Make sure all the holes are aligned. Tighten screws according to the numerical order shown in the image! Do not use excessive force! -
Page 16: Fittings And Tubing
FITTINGS AND TUBING STEP 1 Screw-in two (2) G1/4 threaded male fittings. Attach the liquid cooling tubes and connect the water block to the cooling loop. EK-FITTING Do not forget to plug the remaining two openings using the enclosed EK-Plug G1/4 or its equivalent. EK recommends using EK fittings with all EK water blocks. -
Page 17: Connecting The D-Rgb Led Strip
CONNECTING THE D-RGB LED STRIP STEP 1 Plug the 3-pin connector of the distribution plate D-RGB LED light to the D-RGB HEADER on the motherboard. The LED will work if the pin layout on the header is as follows: +5V, Digital, Empty, Ground. -
Page 18: Warranty
WARRANTY Our products are warranted against defects of materials and quality for a period of 24 months, starting with the date of delivery to the end-user. During this period, products will be repaired or have parts replaced at our discretion, provided that 1) the product is returned to the agent from whom it was purchased;... -
Page 19: Support And Service
SUPPORT AND SERVICE In case you need assistance or wish to order spare parts or a new mounting mechanism, please contact: https://www.ekwb.com/customer-support/ For spare parts orders, refer to the page with “TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS” where you can find the EAN number of each part you might need.