Advertisement
Quick Links
W e strive to ensure that our produc t s are of the highest quality
and free of manufacturing defec t s or missing p ar t s. Howeve r , if
you have any problems with your new product,
please contact us toll free @:
1-88 8 - 9 9 6 - 2 7 2 9
F AX: 1-866-873-3535
gameroom@escaladesports.com
Or w r i t e t o :
Escalade Sport s
Customer Service Departmen t
P .O. B o x 88 9
Evan sville I N 4770 6
Please have your model number when inquiring about parts.
When con t ac ting Escalade S por t s please provide your model numbe r , date code (i f
appli cable ), and pa rt nu mbe r i f reque sting a repla c e men t pa rt. The s e nu mbe rs a re
lo c a ted on the p rodu ct, pa ckaging , and in thi s owne rs manual .
M01484W
Y our Model Number :
2-M01484W-
-GR
Date Code:
Purchase Date:
PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
All Rights Reserved
© 2016 Escalade S por t s
1
For Customer Service Call 1-888-996-2729
Advertisement
Summary of Contents for Redline Sports M01484W
- Page 1 ), and pa rt nu mbe r i f reque sting a repla c e men t pa rt. The s e nu mbe rs a re lo c a ted on the p rodu ct, pa ckaging , and in thi s owne rs manual . M01484W Y our Model Number :...
- Page 2 IMPORTANT! READ EACH STEP IN THIS MANUAL BEFORE YOU BEGIN THE ASSEMBLY. TWO (2) ADU L TS ARE REQUIRED T O ASSEMBLE THIS REDLINE ALLEY OOP SINGLE SHOOTOUT Tools Needed: Allen Wrench (provided) Phillips Screwdriver Plyers Make sure you understand the following tips before you begin to assemble your basketball shootout.
-
Page 3: Hardware Identifier
HARDWARE IDENTIFIER (To Scale) H1 - M6 x 35mm H3 - M6 x 25mm H2 - M6 x 60mm Allen Head Bolt Allen Head Bolt Allen Head Bolt (8 pcs) (1 pc) (2 pcs) H4 - M6 H6 - Plastic Bushing H5 - M6 Flat Washer Wing Nut... - Page 4 PARTS IDENTIFIER (Not to Scale) P1 - Left Lower P2 - Right Lower P3 - Left Middle P4 - Right Middle Tube Assembly Tube Assembly Tube Assembly Tube Assembly (1 pc) (1 pc) (1 pc) (1 pc) P5 - Front P6 - Upper Tube Assembly Tube (2 pcs)
- Page 5 PARTS IDENTIFIER (Not to Scale) P9 - Electronic P10 - Electronic P11 - Mechanical P12 - Rim (1 pc) Scorer (1 pc) Scorer Face Plate Scoring Arm Note: This is a special rim (1 pc) (1 pc) designed to avoid entanglement with the mechanical scoring arm.
- Page 6 Remove all the parts from the box and verify that you have all of the listed parts as shown on the Parts List. NOTE: STEP 1, 2 AND 3 requires a second adult to help “hold” the assemblies as being assembled NOTE: When unfolding assemblies, be careful not to bend any parts.
- Page 7 PARTS REQUIRED: 1 pc - H1 M6 x 35 mm Allen Head Bolt 1 pc - H4 Flat Washer NOTE: Lastly, these six points can now 1 pc - H5 Wing Nut be tightened using a phillips screwdriver or allen wrench (T1) provided and plyers. STEP 3 Connect Middle Tubes Assembly from STEP 2 to Lower Tubes Assembly from STEP 1 using Spring...
- Page 8 PARTS REQUIRED: 2 pcs - H2 M6 x 60 mm Allen Head Bolt 2 pcs - H6 Plastic Bushing 2 pcs - H4 Flat Washer 1 pc - P5 Front Tube Assembly 2 pcs - H5 Wing Nut 2 pcs - P15 Locking Pin STEP 4 Connect P5 Front Tube Assembly using Spring Lock as shown in FIGURE 4.
- Page 9 PARTS REQUIRED: 8 pcs - H3 M6 x 25 mm Allen Head Bolt 1 pc - P7 Backboard 4 pcs - H4 Flat Washer 1 pc - P11 Mechanical Scoring Arm 8 pcs - H5 Wing Nut 1 pc - P12 Rim 8 pcs - H7 Lock Washer 1 pc - P14 Rim Support Plate 1 pc - T1 Allen Wrench...
- Page 10 PARTS REQUIRED: 2 pcs - P6 Upper Tube STEP 8 Attach Backboard assembly from STEP 7 to Frame assembly from STEP 5 using Spring Lock as shown in FIGURE 8. Attach P6 Upper Tubes to P7 Backboard assembly using Spring Lock as shown in FIGURE 8. Spring Lock Spring Lock FIGURE 8...
- Page 11 PARTS REQUIRED: 1 pc - P8 Ramp Chute STEP 9 Slide elastic loops and the sleeve of P8 Ramp Chute onto P6 Upper Tubes as shown in FIGURE 9 and DETAIL C. At the front of P8 Ramp Chute, bring the ramp down and secure using velcro strips as shown in FIGURE 9.
-
Page 12: Storage Position
STEP 10 Connect P11 Mechanical Scoring Arm sensor wire to P9 Electronic Scorer as shown in FIGURE 10. Secure Elastic Loops from P8 Ramp Chute to the back of P7 Backboard attached Wing Nuts as shown in FIGURE 10. Hook Elastic Loop’s over Wing Nuts in five locations as shown in FIGURE 10. Insert 3(three) pieces “AA”... -
Page 13: Product Parts List
Congratulations! You have now assembled your Single Shootout. Please note the Care and Use instructions below. CARE AND USE OF YOUR SHOOTOUT 1. Product can be used OUTDOORS - but must be stored INDOORS. 2. DO NOT sit, climb or lean on the unit. DO NOT drag the unit when moving it, This will damage the legs. -
Page 14: 90-Day Limited Warranty
90 DAY LIMITED WARRANTY This consumer warranty extends to the original consumer purchase of any ESCALADESPORTS Product (hereinafter referred as the "Product"). WARRANTY DURATION: This Product is warranted to the original consumer purchase of a pe- riod of 90 days from the original purchase. WARRANTY COVERAGE: ESCALADE SPORTS warrants to the original Consumer Purchaser that any Product of its manufacture is free from defects in material and workmanship when used for the intended purpose under normal use and conditions.
Need help?
Do you have a question about the M01484W and is the answer not in the manual?
Questions and answers