Page 1
Educational Auto Tracking EPTZ Camera HV-100E User Manual www.hameco.eu...
Page 2
HV-100E User Manual ATTENTIONS This manual introduces functions, installations and operations for this camera in details. Please read this manual carefully before installation and use. 1. Cautions 1.1 Avoid damage to product caused by heavy pressure, strong vibration or immersion during transpor tation, storage and installation.
HV-100E User Manual 1. PRODUCT OVERVIEW 1.1 System introduction Educational tracking camera system is mainly composed of the teacher tracking camera and student tracking camera. The video camera integrates with industry leading 4K ultra-definition imaging tech- nology, image encoding and decoding technology, video analysis technology and electronic PTZ control technology, and realizes a single camera to output close-ups main stream, close-up sub-stream, pan- oramic main stream, panoramic sub-stream and blackboard stream at the same time.
HV-100E User Manual 4. SYSTEM CONNECTION 4.1 Installation Layout Teacher tracking camera is installed at place 1.6-2.1m from ground (distance from panoramic lens to ground), and the distance from the blackboard is 5-9m. Teacher tracking camera should be installed near central axis of the classroom as much as possible to get the best result of tracking camera shoot- ing.
HV-100E User Manual 4.2 System Wiring The teaching tracking camera products provide a smart camera solution for education information field, and customers can select all or some products as needed. Different combinations of products meet the demands of customers’ in various scenarios.
HV-100E User Manual 5. IE LOGIN AND TRACK SETUP PROCESS 5.1 Connecting Mode Direct connection: Connect the camera via network cable to external Internet access of the PC Internet Connection mode: Connect the camera to Internet by Router or Switch and user can log in the device by browser.
HV-100E User Manual To verify whether the network segment has been successfully added, click the “Start” and select “Op- eration” to input cmd, then click OK and open DOS command window, type ping 192.168.5.26, press Enter key to display information shown below, which means network segment adding is succeeded.
HV-100E User Manual 5.3 IE Preview After successful login into the management interface, it enter the video preview interface. In the pre- view screen, users can control PTZ, zoom, focus, video capture, sound, focus, full screen and set the preset position, run, delete and other operations.
HV-100E User Manual Input Volume: Set the input volume (default 2, 1-10 optional) Click “Save”, it will remind ”Enable has changed. Restart the device to take effect after the success of the save.”, then please reboot the cam- era to make new setting effect.
Page 13
HV-100E User Manual 2) Stream Release Stream: You can set any stream release of close-up main stream, close-up sub-stream, panoramic main stream, panoramic sub-stream, and guide stream Switch: To turn on/off close-up main stream, close-up sub-stream, panoramic main stream, panoramic sub-stream and blackboard code stream.
Page 14
HV-100E User Manual Dynamic range: Set the dynamic range (default off, 1-8 optional). Shutter speed: Active when it is status of manual or shutter-priority (default 1/50 1/25 1/30 1/50 1/60 1/90 1/100 1/120 1/180 1/250 1/350 1/500 1/1000 1/2000 1/3000 1/4000 1/6000 1/10000 optional).
HV-100E User Manual 4) Character-Overlapping Display date and time: Set whether to display the time and date (default display). Display Title: Set whether to display the title (default display). Font Color of Time: Set font color of time and date (default white, black, yellow, red, and blue optional).
Page 16
HV-100E User Manual av1 close-up sub-stream, av2 panoramic main stream, av3 panoramic sub-stream, av4 broadcast code stream.) 2) Ethernet parameters DHCP: Enable or disable obtain IP automatically can be set. Save changes and reboot the device to takes effect (default: OFF) IP Address: Set the IP address, save changes and reboot the device to takes effect (default 192.168.5.163).
HV-100E User Manual 5.4.4 System Configuration 1) Device Properties Device Name: Set the device name (the default Camera1, user can add their own). Device ID: Set the device ID (default 1, Read-Only). System Language: Set the system language (default Simplified Chinese, English optional).Need to re-login after modify and save the setting.
HV-100E User Manual Click on the “Upgrade” button, the upgrade dialog will appear, the device will reboot automatically after update successfully. (Note: Make sure the power and network is keeping connected during the process, or the upgrade will fail) Note: After the version upgrade is complete, you need to restore factory defaults;...
HV-100E User Manual 5.6.1 Teacher Tracking Configuration The following instructions are given in accordance with the setup flowchart. The main interface of teacher tracking configuration is shown in Figure 5.6-1 Figure 5.6-1 Operation interface 1. Click stop tracking 2. Preset setting of the platform The operation interface for setting the preset position is shown in Fig.
Page 20
HV-100E User Manual Figure 5.6-2 Operation interface Platform preset: Control teacher tracking camera to make platform (we suggest that teachers stand in the middle of platform, if any) get desired visual result in camera image, then click and save plat- form preset.
Page 21
HV-100E User Manual Panoramic preset: Control teacher tracking camera to allow camera to have almost a panoramic of the classroom (or any position). When tracking target disappears, it can select close-up lens to go back to panoramic position. 4. Area settings (ON: show the mask area; OFF: hide the mask area) 5.
Page 22
HV-100E User Manual Figure 5.6-5 Operation interface 7. Advanced settings Target lost: This feature is to make sure that when the target lost, lens will return to the assigned preset. It has 2 modes for option: panoramic preset and close-up preset.
HV-100E User Manual Track mode (Three for option): Real-time Tracking Mode Movie Mode Area Tracking Mode Figure 5.6-7 Operation interface Tracking sensitivity: It means in teacher tracking mode, how much the action range is required to trigger tracking camera when the tracking target changes from stationary state to motion state. The- higher the action sensitivity, the smaller movement of tracking target that will trigger camera’s track-...
Page 24
HV-100E User Manual Figure 5.6-8 Operation interface P.S. For student tracking, mask area setting is the only configuration that needs to be done. Turn the camera faced to the students, click “Start”, no other configuration is needed. 1. Click “Stop” tracking 2.
Page 25
HV-100E User Manual Figure 5.6-9 Operation interface Panoramic preset: Control student tracking camera to allow camera to have almost a panoramic view of classroom (or any position). When tracking target disappears, it can select to go back to panoramic position.
Page 26
HV-100E User Manual 5. Advanced settings Target lost: This feature is to make sure that when the target lost, lens will return to the assigned preset. The preset position can be selected in one of two modes: maintain original position or panoramic preset position.
HV-100E User Manual Target lost time(s): It means how much time is required (60s by default) for tracking camera to per- form “target lost action” when target is lost (default: return to panoramic preset). For the setting of the action code, see the chapter “6. Recording and broadcasting host connection instructions”.
Page 28
HV-100E User Manual Figure 6.2-1 Operation interface 2. Configuration of action code Modify action code as needed via web browser. Click Advanced settings -> action code; After modification, click save, as shown below: Figure 6.2-2 Operation interface www.hameco.eu...
HV-100E User Manual 7. TECHNICAL PARAMETER Model Number Teacher Tracking Camrea Student Tracking Camera Camera/ Lens Parameters Image Sensor 1/2.8 inch High Quality 4K CMOS Sensor Effective pixels 8.28 megapixel, 16: 9 HDMI Interface 1080P30 1080P29.97 1080P25 720P29.97 U3 Interface:MJPG/H264 1920*1080/1600*896 /1280*720 /1024*576 /960*540...
Page 30
HV-100E User Manual Input/Output Interface 1xHDMI interface Video Interfaces 1xUSB interface 1xLAN interface:10M/100M/1000M adaptive Ethernet port support POE Video Compression H.264,H.265,MJPEG,YUY2,NV12 Format Audio Input Interface Double track 3.5mm linear Input Audio Compression AAC,MP3,G.711A Format Network protocol RTSP,RTMP,ONVIF,GB/T28181 Control Interface...
HV-100E User Manual 8.MAINTENANCE AND TROUBLESHOOTING 8.1 Camera Maintenance 1) Please power off the camera and disconnect the power adapter and socket, if it’s not used for a long run. 2) Use soft cloth or tissue to clean the camera cover.
HV-100E User Manual PRODUCT DISPOSAL Safety For your own safety, this product should only be used with CE and RoHS approved equipment. Using this headset with non-approved equipment would void the warranty of this product. Disposal of your product Municipal waste stream.