Acer Predator PO3-640 User Manual
  1. Manuals
  2. Brands
  3. Acer Manuals
  4. Desktop
  5. Predator PO3-640
  6. User manual

Acer Predator PO3-640 User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Table of Contents -
1
Predator
PO3-640
User's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Predator PO3-640 and is the answer not in the manual?

Questions and answers

Related Manuals for Acer Predator PO3-640

Summary of Contents for Acer Predator PO3-640

  • Page 1 Table of Contents - Predator PO3-640 User’s Manual...
  • Page 2 Acer Group shall not be liable for technical or editorial errors or omissions contained in this manual. The terms HDMI and HDMI High-Definition Multimedia...

  • Page 3: Table Of Contents

    Table of Contents - Table of Contents Memory configuration 1. UPGRADING YOUR COMPUTER ..5 guidelines ..........14 Installation precautions ....5 Removing a memory module .. 15 ESD precautions ......... 5 Installing a memory module ... 16 Required tools ........5 Graphics board ........
  • Page 4 - Upgrading your Computer Upgrading your Computer In this section, you will find: • Instructions on how to replace a hardware component...

  • Page 5: Upgrading Your Computer

    Upgrading your Computer - UPGRADING YOUR COMPUTER Installation precautions Before you install any computer component, we recommend that you read the following sections. These sections contain important ESD precautions along with pre-installation and post-installation instructions. ESD precautions Electrostatic discharge (ESD) can damage your processor, disk drives, expansion boards, and other components.

  • Page 6: Pre-Installation Instructions

    - Upgrading your Computer Pre-installation instructions Always observe the following before you install any component: Make sure that the ODD and card reader slot is empty. Turn off the power to the computer and all peripherals. Unplug the power cord from the computer. Unplug the network cable and all connected peripheral devices from the computer.

  • Page 7: System Upgrade

    Upgrading your Computer - System Upgrade Removing the Left side system cover Before you proceed, make sure that you have turned off your computer and all peripherals connected to it. Read the Pre- installation instructions on page 6. Remove the two screws that secure the system cover to the computer.

  • Page 8: Installing The Left Side System

    - Upgrading your Computer Installing the Left side system cover Align the cover to the sides of the computer and slide the cover toward the front of the computer. Secure the cover with two screws. Observe the Post-installation instructions on page 6.

  • Page 9: System Layout

    Upgrading your Computer - System Layout M2_3 Wifi M2_2 M2_1 HDD1 HDD2...

  • Page 10: Hard Drives

    - Upgrading your Computer Hard drives The computer supports installation of one 3.5-inch SATA hard drives in the internal HDD cage. Removing the 3.5-inch hard drives Perform Pre-installation instructions on page 6. Disconnect the power and data cables from the hard drives.
  • Page 11 Upgrading your Computer - 11 Pull black rack out from HDD cage and take it off. Remove the hard drives from the rack.

  • Page 12: Installing The 3.5-Inch Hard

    - Upgrading your Computer Installing the 3.5-inch hard drives Remove the new hard drive from their packaging. Insert the new hard drive into the black rack. Insert black rack into HDD cage.
  • Page 13 Upgrading your Computer - 13 Connect the power and data cables to the hard drive. Observe the Post-installation instructions on page 6...

  • Page 14: Memory

    DIMM3 DIMM1 Memory configuration guidelines • To ensure data integrity, use only Acer-approved DDR4 3200 MHz • Memory modules must be installed starting with DIMM1 slot. • Always handle memory modules by its edges. • When installing memory modules, populate the DIMM slots according to the table below.

  • Page 15: Removing A Memory Module

    Upgrading your Computer - 15 Removing a memory module Note DIMM slots on the mainboard must be installed only in certain configurations. Numbers next to DIMM slots correspond to installation sequence. Be sure to install the memory module in DIMM1 slot followed by DIMM2 slot.

  • Page 16: Installing A Memory Module

    - Upgrading your Computer Installing a memory module Select an empty DIMM slot. Remove the new memory module from its packaging, handling it by the edges. Align then insert the memory module into the DIMM slot (1). Insert the memory to the slot until the retaining clips snap inward (2).

  • Page 17: Graphics Board

    Upgrading your Computer - 17 Graphics board The computer contains one or two Graphics boards installed in the PCIe x16 slots. The detail configuration will be differed by different models. Removing the Graphics board Perform Pre-installation instructions on page 6. Disconnect the power cables from the Graphics board.
  • Page 18 - Upgrading your Computer Release the latch that secures the graphics board to the mainboard. Detach the Graphics board from the PCIe x16 slot...
  • Page 19 Upgrading your Computer - 19 Remove the screws that secure the Graphics board to the VGA Holder Bracket.

  • Page 20: Installing The Graphics Board

    - Upgrading your Computer Installing the Graphics board Remove the new graphics board from its packaging. Fix Graphics boards on VGA Holder Bracket with three screws Insert the Graphics board into the PCIe x16 slot and press it down until it latches into place. Note...
  • Page 21 Upgrading your Computer - 21 Secure the Graphics board with screws. Connect the power cables to the Graphics board. Observe the Post-installation instructions on page 6...

  • Page 22: M.2 Ssd Module

    - Upgrading your Computer M.2 SSD module The computer contains one M.2 SSD module installed in the M.2 PCIe slot. Removing the M.2 SSD module Perform Pre-installation instructions on page 6. Remove Graphics board. Removing Graphics board. Remove the screw that secures the M.2 SSD module from the mainboard.

  • Page 23: Installing The M.2 Ssd Module

    Upgrading your Computer - 23 Installing the M.2 SSD module Remove the new M.2 SSD module from its packaging. Positioning M.2 SSD thermal pad on MB. M2_3 M2_2 Insert the M.2 SSD module into its slot in the mainboard. M2_2 M2_3 Secure the M.2 SSD with screws.
  • Page 24 - Upgrading your Computer Replace Graphics board. Installing Graphics board. Observe the Post-installation instructions on page 6.
  • Page 25 PredatorSense - 25 PredatorSense In this section, you will find: • Introduction to the PredatorSense utility • How to use PredatorSense...

  • Page 26: Predatorsense

    - PredatorSense 2. PREDATORSENSE PredatorSense (DT) is an Acer proprietary utility to enhance the user experience of Gaming products on Microsoft Windows 11. The central idea of this utility is to provide a user interface to easily control fan speed, Lighting and also display system information.
  • Page 27 PredatorSense - 27 Category Description Provide overview of all features with quick adjustment Home • CPU/GPU/System health information • Fan speed control (Auto, Gaming and Silence) Provide control and adjustment for the LEDs on Front Face, Left Side Face and Rear Face. •...

Table of Contents

Save PDF