VESTEL GAIA Garden Spot Light 2.5w User Manual

GAIA Garden Spot L�ght
User Manual
PACKAGE CONTENT
1- Garden Spot L�ght
PRODUCT DRAWING
Blue (-)
Brown (+)
F�gure. 1
NO DEFINITION
1 METAL CAP
2 FRAME
3 GLASS
4
BODY - GLASS GASKET
5 LENS RETAINER LENS
6 SCREW SK FNI YFMB 2.9*5.2
PCB
7
8 BODY
9 M5*10 SCREW
10 DRIVER CARD
11 DRIVER CARD COVER
12
GASKET
13 DRIVER CARD COVER
14 M4*10 IMBUS SCREW
15 M16*1.5 UNION
16 CABLE
17 M6 SPRING WASHER
RETAINER
18
PILE
19
M6*15 SCREW
20
M5 SPRING WASHER
21
M4*4 STAY BOLT
22
SAFETY WARNINGS
Do not use the dev�ce �f �t �s dropped or exposed to a shock. R�sk of �mproper
operat�on.
If the dev�ce �s turn�ng off or not operat�ng properly, never attempt to repa�r the
dev�ce by yourself. Please contact author�zed serv�ce.
Do not look d�rectly at the product wh�le �t �s �n operat�on. Strong l�ght can cause
v�sual problems.
Never cover the dev�ce w�th paper of clothes or place the dev�ce close to
flammable mater�als, otherw�se can cause to f�re or the dev�ce can operate
�mproperly.
Keep a d�stance between the dev�ce and the �tem to be �llum�nated. If the d�stance
�s very l�ttle, �t can cause d�scolourat�on or deformat�on of the �tem or f�re.
Do not use the dev�ce for any dut�es except for �llum�nat�ng.
Product. Compl�es w�th the AEEE Regulat�on.
CAUTION
Do not clean the surface of the product w�th flammable mater�als such as alcohol,
gasol�ne or acetone.
Do not use the dev�ce �n an atmosphere of corros�ve gasses.
When �nstall�ng the dev�ce, make sure the power supply �s off.
Ma�ns connect�ons should be done by techn�cal serv�ce personnel. For the ma�ns
connect�ons, all �nstallat�ons of connectors, term�nals, etc. should be �n accordance
to the cable cross sect�on and local w�r�ng regulat�ons. Author�zed serv�ce
personnel �s respons�ble for �nstall�ng requ�red protect�ve dev�ces such as c�rcu�t
PIECES
breaker and fuse box, ma�nta�n�ng requ�red �nsulat�on clearances between the
1 condu�ts, and tak�ng necessary precaut�ons aga�nst electr�cal shock that could be
r�s�ng because
1
of these connect�ons. If outer elast�c cable or cord gets damaged, �t should be
1
replaced by new ones. Th�s task can only be done by techn�cal serv�ce or
1
manufacturer.
1
Surface of the product can be hot when operat�ng. Do not touch the product, unless
3
turn�ng �ts power off and lett�ng to cool down.
3
Cable requ�red for connect�ng power supply to �nput term�nals must have m�n�mum
1
sect�on of 2x1mm² qual�f�ed as H05RN-F.
1
2
2
1
1
1- Install the �nd�cated bolt �nto the hole �n arrow d�rect�on (F�gure.2)
4
2- Mount the washer �nd�cated by c�rcular arrow w�th bolt connect�on.
1
1
1
1
1
1
2
1
INSTALLATION INSTRUCTIONS
F�gure.2