Related Manuals for Electronics SP44
Summary of Contents for Electronics SP44
- Page 1 CONTROLLERS FOR CENTRAL HEATING BOILERS MICROPROCESSOR BOILER HEATER TEMPERATURE CONTROLLER SP44 MANUAL WARRANTLY CARD...
-
Page 2: Front Panel Description
Manual SP-44 1. Front Panel Description The view of the controller with its functionalities marked 1. Power ON (Hold the ENTER button for 2 seconds) 2. LCD Display 3. Control lights 4. Control buttons 5. Blower switch ON light. 6. Central Heating (C.H.) switch ON lamp 7. - Page 3 Manual SP-44 2. Usage This device is designed to automatically manage the cauldron, turn on the pumps: the circulation pump, water pump, and floor heating pump, within the central heating installation. The controller cooperates with the auger of the cauldron. The control process is managed by the control of the liquid temperature inside the central heating cauldron.
-
Page 4: Fuel Supply
Manual SP-44 AIR TEMPERATURE 100 C The ( ) button, allows menu navigation, parameter changes, change of central heating temperature, turn ON/OFF summer mode. The ( ) button, allows menu navigation, parameter changes of the Hot Water Tank, turn ON/OFF the hot water tank. All parameters in settings menu are individually depending on type of the installatin, and the caloric value of the fuel. - Page 5 Manual SP-44 - BLOWER POTENCY - this function is BLOWER POTENCY used to set the potency with which the blower insufflates air to the hearth. BLOWER POTENCY - SUSTAINING OPERATION SUSTAINING OPERATION - SUSTAIN PAUSE - this function allows SUSTAIN PAUSE to set an intermission between turning on the blower and turning on the conveyer in sustain mode.
- Page 6 Manual SP-44 - H.W.S.T. PRIORITY - H.W.S.T. starts H.W.S.T. PRIORITY working, and operates until the temperature reaches the level set. Once the usable water reaches the desired temperature the H.W.S.T. pump turns off and C.H. and floor heating turns on. - C.H.
-
Page 7: Floor Heating
Manual SP-44 - SETTING THE CLOCK - after pressing ENTER button we enter the clock settings. Using buttons ( ) we set flashing parameter, and with the ENTER button we confirm and go the next parameter. - ECONOMICAL MODE (PI) - it is based MF0 06:30 - 7:30 on precentage reduction of the supplied MF1 13:00 - __:__... -
Page 8: Install Settings
Manual SP-44 - DEFAULT SETTINGS - the controller DEFAULT SETTINGS has pre-programmed settings; we can go back to those settings at any time. However we need to remember, that all personal settings will be lost. DEFAULT SETTINGS - END OF WORK - turning off the END OF WORK controller in order to turn it on again - we need to press and hold the EXIT button. -
Page 9: Engine Type
2. The Electronics Company is not responsible for choosing incorrect blower engine settings. Such damage will not be subject to the warrantly. - BLOWER STARTUP - this function is used... - Page 10 Manual SP-44 - HELIX TEMPERATURE - this function HELIX TEMPERATURE prevents the fuel in the cauldron bin from ignition. If the helix temperature goes up beyond the one set up by the user conveyer starts supplying fuel for 10 MAX HELIX minutes to prevent the fuel in the TEMPERATURE 60 C...
-
Page 11: Error Messages
Manual SP-44 5. Usage 1. Connect power supply to C.H. and H.W.S.T. pums as well as to the floor heating pump: a. to „grounding” clamp the green-yelow, b. to „N” clamp the blue wire, c. to „L” clamp the brown wire 2. -
Page 12: Fuse Exchange
Manual SP-44 7. Fuse exchange To change the fuse it is essential to disconnect the power cable from the socket. 8. Fitting recommendations 1. The controller should be fitted by a skilled person. 2. The controller should be located in a place where it won’t get warmed up over 40 C. -
Page 13: Warranty Card
Warrantly card 10. Warranty card 1. Manufacturer guarantees good quality of equipment, guarantee and post-guarantee services. 2. Manufacturer grants the guarantee of failure-free controller operation for the period of 24 month from purchase date. 3. Failures and damages revealed during warranty period shall be eliminated immediately, free of charge within not longer than 14 days from the day of delivering the device for repair at manufacturer location. - Page 14 Warrantly card...
- Page 15 Notes...
- Page 16 MANUFACTURER: Electronics S.C. Paweł Wilgocki, Piotr Wilgocki ul. Moczydło 10a, 30-698 Kraków tel. 012 650 47 90, fax 012 650 47 91 e-mail: biuro@electronics.net.pl...