Advertisement
Quick Links
August 2019
901097-001
Rev 00
About This Guide
This guide is intended for Fusion jukebox Operators and technicians, as well as TouchTunes field services.
Topics
•
Assumptions
•
Fusion Jukebox Weight and Dimensions
•
Fusion DIY Enclosure Bracket
•
Required Dimensions for the Fusion DIY Enclosure
•
Important Design and Installation Considerations
•
Heat and Airflow Clearance Warnings
•
Electrical and Wiring Warning
•
Weight Restrictions
•
Assembly of the Fusion DIY Enclosure Bracket
•
Installation of the Fusion DIY Enclosure
•
Disclaimers
•
Jukebox Warranty
•
Disclaimer
•
Limitation of Liability
•
Disclosure
Assumptions
It is assumed that:
•
You have a Fusion jukebox before you start the design of its DIY enclosure.
•
You have the Fusion DIY Enclosure Bracket Kit (P/N 600308-001).
•
You have installed the Fusion jukebox using the Fusion Installation and Setup Guide (P/N 901095-001) prior
to the installation of its DIY enclosure.
•
You have the three wing bolts (P/N 200302-001) provided from the Fusion Accessory Kit (P/N 600299-001).
Such Accessory Kit is shipped with the Fusion jukebox.
Fusion DIY Enclosure User Guide
Advertisement
Summary of Contents for Octave TouchTunes Fusion DIY
- Page 1 August 2019 901097-001 Rev 00 Fusion DIY Enclosure User Guide About This Guide This guide is intended for Fusion jukebox Operators and technicians, as well as TouchTunes field services. Topics • Assumptions • Fusion Jukebox Weight and Dimensions • Fusion DIY Enclosure Bracket •...
- Page 2 Fusion DIY Enclosure User Guide Fusion Jukebox Weight and Dimensions Fusion Jukebox Weight and Dimensions These tables show the weight and dimensions of the Fusion jukebox. Fusion Jukebox Weight Fusion jukebox (with no Modular Hardware Platform) 47 lbs (21.32 kg) Wall bracket 5 lbs.
- Page 3 Fusion DIY Enclosure User Guide Fusion DIY Enclosure Bracket Fusion DIY Enclosure Bracket The Fusion DIY Enclosure Bracket Kit is shipped with the following metal bracket pieces (which must be assembled as follows). Fusion DIY Enclosure Bracket Kit The Fusion DIY Enclosure Bracket Kit is shipped with this document (P/N 901097-001).
- Page 4 Fusion DIY Enclosure User Guide Required Dimensions for the Fusion DIY Enclosure Required Dimensions for the Fusion DIY Enclosure The following shows the dimensions of the Fusion DIY Enclosure Bracket (over which your Fusion DIY enclosure must be installed). These are the minimum required dimensions for your Fusion DIY enclosure. Fusion DIY Enclosure Bracket dimensions...
- Page 5 Fusion DIY Enclosure User Guide Important Design and Installation Considerations Fusion DIY Enclosure Bracket screw holes and slots Important Design and Installation Considerations • Screw holes highlighted in green in the previous figure are required to be installed. Therefore, your Fusion DIY Enclosure must be designed, built, and installed accordingly.
- Page 6 Fusion DIY Enclosure User Guide Important Design and Installation Considerations Heat and Airflow Clearance Warnings ATTENTION: Do not obstruct the top and bottom vents on the Fusion jukebox. Your Fusion DIY Enclosure must allow for space above and below the top and bottom vents and for at least 1 inch of space from the wall.
- Page 7 Fusion DIY Enclosure User Guide Assembly of the Fusion DIY Enclosure Bracket Assembly of the Fusion DIY Enclosure Bracket 1. Fasten the metal support piece to the bracket using the four screws provided in the Fusion DIY Enclosure Bracket Kit. Fasten bracket screws 2.
- Page 8 Fusion DIY Enclosure User Guide Installation of the Fusion DIY Enclosure Installation of the Fusion DIY Enclosure 1. Install the assembled bracket within the Fusion DIY Enclosure. The following shows a sample enclosure. Bracket within a sample enclosure 2. Fasten the bracket to the enclosure using as many mounting points as possible. The minimum required mounting points are the 4 screw holes at the bottom of the bracket and the 6 screw holes at the very top of the bracket (see figure Fusion DIY Enclosure Bracket screw holes and...
- Page 9 Fusion DIY Enclosure User Guide Installation of the Fusion DIY Enclosure 5. Slide the Fusion jukebox screen up slightly from its bottom panel and then lift it out. CAUTION: Be careful not to pinch your fingers when opening the screen L brackets in the next step.
- Page 10 Fusion DIY Enclosure User Guide Installation of the Fusion DIY Enclosure 7. Place the assembled bracket/enclosure over the Fusion jukebox so that the screen passes through the opening at the center of the enclosure. The following shows a sample enclosure. Place enclosure over the Fusion jukebox...
- Page 11 Fusion DIY Enclosure User Guide Installation of the Fusion DIY Enclosure 8. Align the metals struts of the bracket with the metal plates located on top of the Fusion jukebox as you slide the enclosure into place. The following shows the position of the bracket on the Fusion jukebox chassis without the enclosure as a visual example only.
- Page 12 Fusion DIY Enclosure User Guide Installation of the Fusion DIY Enclosure 11. Secure the Fusion DIY Enclosure to the Fusion jukebox by hand-tightening the three wing bolts to the top interior of the Fusion jukebox (the location for each wing bolt is circled in green in the following figure). Location for wing bolts (interior of the Fusion jukebox) 12.
- Page 13 Disclaimers Jukebox Warranty The Octave Music Group, Inc. provides a separate product warranty for the Jukebox. Installation and use of the Fusion DIY Enclosure Bracket Kit (the “Kit”) in strict accordance with this Fusion DIY Enclosure User Guide (the “Guide”) shall not void the applicable Jukebox warranty. Notwithstanding the foregoing, other acts or omissions of you, your personnel and your subcontractors may void the Jukebox warranty, including without limitation (a) installation of the Kit not in compliance with this Guide;...
Need help?
Do you have a question about the TouchTunes Fusion DIY and is the answer not in the manual?
Questions and answers