Table of Contents
Advertisement
Quick Links
MR-2100AC-XX/W1615MR-XX
Quick Installation Instructions
Document Number: 830-04406-01
February 2021
Package Contents:
•
1 x MR-2100AC-XX or W1615MR-XX
•
1 x Quick Install Guide
•
1 x Power supply
Installation
For installations with more than one
MR-2100AC-XX/W1615MR-XX, select one unit to be used as
the main MESH controller and follow the instructions presented
on the current document.
1. Mounting
The MR-2100AC-XX/W1615MR-XX may be mounted on
flat surfaces such as a desktop. The
MR-2100AC-XX/W1615MR-XX is equipped with an
extendable base to enhance stability.
2. Connect Power
a.
Plug the round two pin 12V DC power connector of
power converter into the
MR-2100AC-XX/W1615MR-XX power port
b.
Plug the input of power converter into a live AC outlet
c.
Verify that the POWER LED on the
MR-2100AC-XX/W1615MR-XX is solid white
indicating local power is on and voltage is good
See MR-2100AC-XX/W1615MR-XX LED Behavior
for a complete description of the LEDs.
3. Configuring SSID and Wi-Fi Key (Optional)
This step is optional. Each MR-2100AC-XX/W1615MR-XX
comes with a set of default Wi-Fi SSID and passphrase
located on the bottom information label. If using the
defaults, step 3 (this step) may be skipped.
a.
Power up the MR-2100AC-XX/W1615MR-XX as
described in the previous step,
is the main MESH controller
b.
Use a UTP cable between
MR-2100AC-XX/W1615MR-XX Ethernet ports and a
PC Ethernet port
c.
Configure a fixed IP address on your PC, for example
192.168.1.101 (for detailed instructions refer to your
operating system documentation; for Windows OS
follow these instructions
en-us/help/15089/windows-change-tcp-ip-settings)
d.
Open a web browser and input http://192.168.1.100
e.
When prompted for credentials enter "admin" as user
and for password "DZSXXXXXXXXX" where
Copyright © 2021 DASAN Zhone Solutions
Connect
Power. This
https://support.microsoft.com/
"XXXXXXXXX" is the 9-digit serial number found on
the unit label
f.
Navigate to WiFi > EasyMesh > Advanced
g.
Click Configure BSS
h.
Click Edit BSS
i.
Change SSID
j.
Change Password
k.
Click Save and Apply
l.
If needed repeat for 2.4Ghz Wi-Fi
NOTE: by default, when changing the configuration of
the 5GHz radio, the configuration of the SSID and
passphrase will be replicated on all radios and all
access points forming part of the MESH ecosystem.
Document Number: 830-04383-01
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for DZS MR-2100AC-XX
- Page 1 Navigate to WiFi > EasyMesh > Advanced For installations with more than one Click Configure BSS MR-2100AC-XX/W1615MR-XX, select one unit to be used as the main MESH controller and follow the instructions presented Click Edit BSS on the current document.
- Page 2 4. Setting Up Your MESH Network RED MESH LED indicates that the MESH link quality The first MR-2100AC-XX/W1615MR-XX is the MESH is too low. While the LED is solid, even if its RED, the controller. This procedure assumes that the SSID and the MESH link is active.
- Page 3 The band 5150-5250 MHz for this device are restricted to indoor use only within all European Union countries. Hereby, [DZS, Inc] declares that the radio equipment type [MR-2100AC-XX, W1615MR-XX] is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.dzsi.com.
- Page 4 This product may contain copyrighted software that is licensed under the GNU General Public License (“GPL”), a copy of which is avail- able at www.gnu.org/licenses. You may obtain a copy of such software, in source code form, from DZS for a period of three years after our last shipment of the product by following the instructions at www.dasanzhone.com/gplinfo.
Need help?
Do you have a question about the MR-2100AC-XX and is the answer not in the manual?
Questions and answers