Page 1
Ground Pull Manure Spreaders FH-25/27G Save This Manual for Future Reference OPERATION & PARTS MANUAL Please read these instructions carefully before using! You must GREASE ALL FITTINGS BEFORE OPERATING! www.Betstco.com Toll Free: 877-876-7895, E-mail: sales@betstco.com 83371 Melton Rd, Creswell OR 97426 Rugged Labor Saving Equipment Since 1995 Farmer-Helper 25 &...
Contents Guide to this Manual................3 For Your Safety............................3 Safety Labels............................4 SECTION 2: OPERATION..............7 Understanding Spreader Operation......................7 The Spreader Operating Components....................7 Connecting the Spreader to the Towing Vehicle................7 Guidelines for Loading the Spreader for Operation................8 Operating the Spreader........................9 SECTION 3: MAINTENANCE & ADJUSTMENT......10 Guidelines for Regular Maintenance.......................10 Procedures for Spreader Adjustment....................15 Adjusting the Rear Pawl........................15...
SECTION 1: INTRODUCTION Guide to this Manual This m anual contains all the information necessary to safely operate and m aintain the F a r m e r H e l p e r 27+ or 37+ Spreader. Consult the Table o f Contents for a detailed list of topics covered. You'll find this m anual's step-by- step procedures easy to follow and understand.
For Your Safety... (continued) In addition to observing the specific precautions listed through out the m anual, th e following gen eral must be heeded p re c a u tio n s a p p ly a n d f o r p r o p e r , safe o p eratio n .
Page 5
Safety Labels (continued) S p r e a d e r S afety L ab els Label P art# Description 42792 D A N G E R -N O riders 42710 WARNING - Flying Debris 42756 WARNING - Entanglem ent, Do NOT operate w ithout shields 42772 WA RN IN G - Spreader com bination safety label - m oving parts, read manual 42814...
SECTION 2: OPERATION Understanding Spreader Operation Proper and safe operation o f th e F a r m e r H e l p e r 27G Spreader requires: (1) being fam iliar w ith the spreader's operating com ponents and (2) heeding all safety precautions as stated in this manual. The Spreader Operating Components By definition, the left and right sides o f the spreader are determ ined while sitting on the tractor seat.
Attaching the Spreader to the Towing Vehicle (continued) R efer to Figure 2B. A djust the overall height o f the spreader/hitch w ith the dolly w heel/jack so the height o f the spreader hitch m atches the height o f the tractor drawbar or vehicle hitch point (as applicable).
Operating the Spreader Before proceeding with operation of the spreader, review all safety statements as provided in Section 1 of this manual. WA R N IN G : To prevent serious personal inj ury, ensure that A LL safety shields are in place on the spreader before starting operation.
SECTION 3: MAINTENANCE & ADJUSTMENT Guidelines for Regular Maintenance WA R N IN G : All shields m ust be replaced after m aintenance or adjustm ent procedures are perform ed. Failure to do so could result in serious personal injury or death. Perform ing regular m aintenance on your F a r m e r H e l p e r Spreader w ill help ensure optimal performance.
Page 11
Guidelines for Regular Maintenance (continued) Periodically check the floor apron chain for tension/tightness (refer to Figure 3A). P ro c e d u re fo r check in g / adju stin g th e flo o r a p ro n c h a in : firmly a) Pull up on the center slat o f the floor apron chain.
Page 12
LUBRICATION The Model 27G is designed to require little maintenance and lubrication. However, it is still important to keep all moving parts well lubricated. Following a regular maintenance and lubri- cation schedule will enhance the operation and increase the life of the spreader significantly. The following pages show the grease points on the spreader.
Page 13
LUBRICATION There is one grease fitting on each axle bearing. Figure 8 There is one grease fitting on each rear web bearing. Figure 9 There is one grease fitting on each beater bearing. Figure 10 Farmer-Helper 25 & 27G Revision06/2017...
Page 14
LUBRICATION Lubricate the apron chain with SAE #30 oil or similar lubricant at least twice yearly. More often if the manure is of high acid nature or if the spreader is stored outside. Regular lubrication of the apron chain will substantially increase its life Figure 11 Lubricate the beater drive chain with en-...
Procedures for Spreader Adjustment Problem s w ith spreader operation m ay indicate that certain adjustm ents are required to restore proper function. The follow ing procedures address com m on problem s w hich m ay be encountered in spreader operation. Adjusting the Rear Pawl If th e floor apron chain is not m oving, the m ost comm on cause is im proper brake (rear) pawl adjustment.
Procedures for Spreader Adjustment (continued) Re-installing the Beater The follow ing procedure explains how to re-install the chain should this ever becom e necessary. A s needed, refer to the B e a ters a n d D riv e A ssem bly parts detail in A p p en d ix A at the back o f this m anual. D isconnect the spreader from the tractor.
APPENDIX A: PARTS REFERENCE The follow ing inform ation is provided for your reference in understanding how the spreader is assem bled and how spare parts can be identified and ordered properly. General Spreader Specifications *NOTE: The tires are mounted in reverse direction of "normal" installation. Farmer-Helper 25 & 27G Revision06/2017...
Page 21
Spare Parts List of Spreader Box Assy PART NO. Name & Specifications 25G.10.011 Spreader Box Weldment 25G.10.012 Push Arm Shield Weldment 25G.10.013 Push Arm Engaging Arm Weldment 25G.10.014 Endgate Frame Weldment 25G.10.015 Lever Pivot Weldment, Left 25G.10.016 Lever Pivot Weldment, Right 25G.10.017 Engaging Linkage Weldment, Right 25G.10.018...
Spare Parts List of Transmission Assy PART NO. Name & Specifications 25G.20.011 Web Bearing Weldment 25G.20.012 Push Arm Weld Weldment 25G.20.013 Ratchet Wheel Weldment 25G.20.014 Ratchet Arm Weldment 25G.20.015 Ratchet Dawg Weldment 25G.20.016 Idler Dawg Weldment 25G.20.017 Front Web Idler Weldment 25G.20.018 Web Slat Weldment 300053...
Page 33
Spare Parts List of Hitch Assy PART NO. Name & Specifications 25G.60.011 Hitch Weldment 25G.60.012 Adjustable Hitch Weldment 25G.60.013 Dolly Jack Bracket Weldment Dolly Wheel Jack Assembly GB889 1-M12 Lock Nut M12 GB5782-M12 80 Bolt M12 80 M12 80 GB97 1-10 Plain Washer 10 GB889 1-M10 Lock Nut M10...
Page 34
Parts Request Form Fax to 541‐895‐2756 or E‐mail cservice@betstproducts.com Name: Model Number: Address: Serial Number: City State Zip: Purchased From: Phone: Purchase Date: E‐mail: ItemNo. Description Price Amount Comments: Farmer-Helper 25 & 27G Revision06/2017...
Page 35
Farmer Helper Machinery Brand LIMITED WARRANTY FARMER HELPER MACHINERY CO. LTD. warrants to original Purchaser that F A R M E R H E L P E R M A C H I N E R Y C O . L T D . products are free from major defects in material under normal use and service for a period of Two (2) Years from the date the product is purchased or shipped, whichever is later.
WARRANTY VOID IF REGISTRATION IS NOT RECEIVED OR RECORDED ONLINE WITHIN 30 DAYS OF PURCHASE DATE OR SHIP DATE, WHICHEVER IS LATER. FARMER HELPER MACHINERY REGISTRATION Item________________________________Model # _________________ Purchase Date_____/_____/_______ Purchased From: ________________________________Gift� Inv#/Order# ____________________________ Owner Name: _______________________________________ Serial # (if Applicable)______________________ Owner Address: _______________________________________ City: ________________________ County: ___________ ST: ______ Zip Code: _____________ Phone: _______________________ Email: ________________________...
Page 37
2 YEAR EXTENDED WARRANTY & REGISTRATION Farmer Helper Machinery Branded Products 2 YEAR EXTENDED WARRANTY 2 Year Extended Warranty amends to original Recorded Manufacturers Warranty Registration the time period of described coverage. Extended Warranty does not apply to Consumable and Expendable Items as described in Product Warranty Registration. This Amendment does not affect any other part of recorded Warranty Registration or Policy.