Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for TranzX ES 504
Summary of Contents for TranzX ES 504
- Page 1 Technical Manual ES 504/ES 506 Version 01-2011 English...
- Page 2 Introduction Congratulations on the purchase of a TranzX PST e-bike that will give you many kilometres of cycling pleasure with a comfortable riding feeling. The TranzX PST e-bike offers a perfect synergy between the cyclist’s pedal input and additional power support.
-
Page 3: Table Of Contents
Content Features Your TranzX PST e-bike Assembly instruction Display 9-10 Dynamic Diagnostic System (DDS) Calibration How to charge the battery Maintenance of the battery Factors for the range Terms of warranty Frequently asked questions (FAQ) 17-18 Troubleshooting 18-19 Safety warnings... -
Page 4: Features
Features of TranzX PST- • Electronic Pedalling Assistance • Power support only while pedaling, and stops, when you stop to pedal. • Perfect synergy between cyclist’s pedal input & additional power support. • 1:1 direct response between pedal force and power support. -
Page 5: Your Tranzx Pst E-Bike
TranzX PST e-bike Diagram of electronic components ES504 ... - Page 6 ES506 ...
-
Page 7: Assembly Instruction
Assembly Instructions Philipps Head Screwdriver 4mm, 5mm, 6mm Allen Key Wrench 8mm, 9mm, 10mm, 13mm, 14mm, 15mm & 19mm Side Cutter Unpacking Carefully remove all packing material from the bicycle and inspect the bike for any damage which may have occurred during shipping. - Page 8 Stem Assembly Fit the cable guide onto the head set (Img. 6). Remove the plastic cap from the stem quill (Img. 7). Insert the stem into the head tube (Img. 8). Make sure the stem does not exceed the minimum insertion height Img.
- Page 9 Saddle & Seat Post Assembly counter-clockwise in order to loosen the clamp ( Turn the quick release Img. 15). Make sure the seat post never exceeds the minimum or maximum insertion height (Img. 16). After inserting the seat post, retighten the quick release clamp by turning it clockwise (Img.
-
Page 10: Display
Display instructions 1. Background light 2. On/Off button – Turns power on and off 3. Mode button • Mode 1: Economy • Mode 2: Normal • Mode 3: Climbing • Mode 4: Turbo 4. Total distance / Trip distance • Total distance will be displayed during stoppage. •... - Page 11 DP03 DP05 DP06 DP07 DP08 DP09...
-
Page 12: Dynamic Diagnostic System (Dds)
The „Cut-off“ brake sensor is without function Flashing battery Battery doesn´t show capacity. Signal: Disconnection of communication between icon battery and system * Please contact our TranzX PST Service Center at service@tranzxpst.com or +49-6032-92671-50 if other malfunctions should occur. -
Page 13: Calibration
Press the background light button for approx. 6 seconds until the display shows “CALXX.X”. This procedure calibrates the TranzX PST-System. After this, you can start riding your bicycle. Note: Make sure to exercise this procedure after adjusting or removing the rear wheel, after replacing the Img. -
Page 14: How To Charge The Battery
How to charge the battery Only use the charger that was supplied by TranzX PST. The use of any other charger voids your warranty, may result in severe damage to the battery and electrical system of the bicycle, and in the worst case may cause a fire hazard. -
Page 15: Maintenance Of The Battery
Battery Maintenance Have you recharged your battery pack lately? If 3 months have passed without recharging, it’s time to do it again for several times. Charging your battery regularly will help insure maximum battery life and performance and will help to avoid battery damage. Important Note •... -
Page 16: Factors For The Range
Factors to maximize the range of your e-bike • Rider Input The more the rider pedals, the further the range. • Difference in elevation The flatter the terrain, the further the range. • Weather Very cold weather could cause discharging the battery. •... -
Page 17: Terms Of Warranty
General warranty regulations General warranty regulations For the exact warranty regulations please contact the manufacturer of the bike directly. NOT covered under warranty… …parts under normal wear and tear and those which require replacing, such as tires, chains, sprockets, brake pads, etc. are not covered. Warranty will also be refused if damage is deemed to have been caused by misuse or accident. -
Page 18: Frequently Asked Questions (Faq)
The range depends on how much you pedal, how many hills you climb, the terrain, the outside temperature, and your weight. On an average single charge, for an average rider on a flat surface, the TranzX system can last up to 100 km. -
Page 19: Troubleshooting
Can I ride my TranzX PST e-bike off-road? No. This TranzX PST e-bike is only suitable for normal trails as well as paved streets and bicycle paths. However, it is not suitable for extreme terrain. Can I ride my TranzX PST e-bike as a normal bike without motor support? In “Off”... - Page 20 Display does not show the current speed or the speed indicator is fluctuating constantly Contact your dealer. Battery icon is flashing The display cannot read the battery capacity but the bike can still ride. In such situations, please contact your local dealer directly (Img 28). Wrench icon is blinking Make sure the cable for the torque sensor on the dropout has not been damaged (Image 29, 30 und 31).
-
Page 21: Safety Warnings
TranzX PST e-bike. 2. Thoroughly inspect your TranzX PST e-bike for loose or damaged parts before each use. If there are any loose or damaged parts, perform the needed adjustments or repairs before starting your TranxZ PST e- bike.
Need help?
Do you have a question about the ES 504 and is the answer not in the manual?
Questions and answers