Avatar BM-A01 User Manual

BM-A01
Application Range
By using this product, you can achieve wireless MIDI
communication between MIDI equipped instrument with smart
device supporting wireless MIDI, such as iPhone, iPad, iPod touch,
Mac, and PC with Windows 10 Autumn Creators Update and
above and Bluetooth 4.0. MIDI adaptor needs the software
supporting Bluetooth MIDI. Please ensure your software can
transmit Bluetooth MIDI.
Note：
There is few MIDI equipment not meeting MIDI standard, in
which No.2 hole as below is not connected to the ground wire
and cannot be used for the power supply of this product.
The following figure：
CAUTION
Always follow these instructions, including but not limited to the
following instructions:
The product is a wireless product and can generates a
magnetic field.
Do not use the product near medical products or inside
medical units.
Do not bring this product within 22cm(9 in.)of anyone having
a heart pacemaker or defibrillator implant. Radio waves
emanating from this product or magnetism emanating from
internal magnets of this product may adversely affect a heart
pacemaker implant or defibrillator implant.
Do not use this product in the vicinity of a TV, radio, stereo
equipment, or other electric devices. Otherwise, this product,
TV, or radio may generate noise. When you use this product
along with an application on your iPad, iPhone or iPod touch,
we recommend that you set "Airplane Mode" to "ON" on that
device in order to avoid noise caused by communication.
This product uses magnets. Persons having heart pacemaker
implants or defibrillator implants must not use this product.
Because of this danger, do not bring this product close to
people with pacemaker or defibrillator implants.
Do not open and repair
Do not open the unit and try to analyze the parts. Do not make
any changes for any internal parts. The unit has not parts
repairable for users.
Specification:
Color
Size
Weight
Indicator Light
Bluetooth Standard
Connector
Power Supply
Power Consumption
Supporting System
User Manual
Black
16mm(D)*70mm(L)*2pcs
20 g
LED*2
Bluetooth Ver 4.0 and above;
MIDI interface *2 (IN, OUT)
MIDI OUT
20 mw
iOS 8 or later, OS X Yosemite or later, Windows 10 Autumn Creators
Update or later.
Wireless MIDI Adaptor
Never use or store in places that are
Over-temperature site (e.g., direct sunlight in an enclosed
vehicle, near a heating duct, on top of heat-generating
equipment)
Damp or humid locations such as baths, washrooms, on wet
floors, or are exposed to rain.
Dusty places；A place of intense vibration；A place with
extremely low temperatures.
Use the product on the specified device
Do not connect this product to devices other than MIDI devices.
If any abnormality is found
If any abnormality is found, immediately disconnect the power
switch of the connected device and remove it from the device,
especially if they smell or smoke.
HXW company shall not be responsible for the damage,
loss of data and equipment damage caused by the user's
failure to follow the instructions.
The Connection Guide
Create a wireless MIDI connection between MIDI devices and
iPhone/iPad:
1.
Please close power supply of the MIDI device , and exit the
software that has been opened on the iPhone/iPad/PC.
2.
Connect the MIDI adaptor to the MIDI port as shown below.
3.
Open the power supply of equipment, the light on product will
be flashing rapidly.
4.
Enter the iPhone/ipod/PC's setting interface, open bluetooth
function.
5.
Start iPhone/ipod/PC application, and then make the
appropriate wireless connection settings. If the wireless
connection is successful, the light will enter slow breathing
pattern.
Take "GarageBand" for example:
1.
Open "GarageBand" application
2.
Click the "Settings" button in upper right corner;
3.
Click "Advanced";
4.
Click "Bluetooth MIDI Devices";
5.
Choose "BM - A01";
6.
Wait for "Not Connected" to become "Connected".
The MIDI adaptor is not visible in the Settings menu of iOS
operating system.It is visible only in applications that
support Bluetooth MIDI.