Subscribe to Our Youtube Channel
Summary of Contents for Plum Brivis Contour Series
- Page 1 Evaporative Cooling Operation Manual Brivis Contour Series, Brivis Promina Series, Brivis Advance Series, Brivis AD Series...
-
Page 2: Regulatory / Installation / Safety
WARNINGS AND IMPORTANT INFORMATION READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE. Failure to carefully read and follow all instructions in this manual can result in equipment malfunction, property damage, personal injury and/or death. WARNINGS: WHEN IGNORED, CAN RESULT IN SERIOUS INJURY OR DEATH. CAUTIONS: WHEN IGNORED, CAN RESULT IN MINOR INJURY OR PRODUCT DAMAGE. -
Page 3: Models Covered In This Manual
No responsibility will be accepted for installation or operation of damaged or incorrect appliances. Installation of damaged or incorrect appliances may also contravene local regulations. MODELS COVERED IN THIS MANUAL Brivis Contour Series Brivis Promina Series Brivis Advance Series... - Page 4 EVAPORATIVE COOLER OPERATION EVAPORATIVE COOLER OPERATION INTRODUCTION Congratulations on your purchase of a Brivis Cooling system. For you to achieve the performance and efficiency expected INTRODUCTION from your new cooler, please ensure the installer is a qualified trades person, that the installer has commissioned the unit before you commence operating, and you take the time to read the contents of this manual. Congratulations on your purchase of a Brivis Cooling system. For you to achieve the performance and efficiency expected from your new cooler, please ensure the installer is a qualified trades person, that the installer has commissioned the unit before you commence operating, and you take the time to read the contents of this manual.
- Page 5 When the cooling is first turned ON, there will normally be a delay before the cool air is delivered from the duct outlets. The the filter pads. Brivis Contour Series models have an additional delay to allow time to open the ServoSeal damper. delay will vary depending on the model of cooler, but this doesn’t mean the cooler is not operating. Most models have pre- The entire process can take up to 8 minutes before cool air is expected from the duct outlets�...
- Page 6 NETWORKER WALL CONTROL OPERATION NETWORKER WALL CONTROL OPERATION ABOUT YOUR BRIVIS NETWORKER WALL CONTROL ABOUT YOUR BRIVIS NETWORKER WALL CONTROL The Brivis Networker wall control operates the complete cooling system, communicating key information and The Brivis Networker wall control operates the complete cooling system, communicating key information and sensing the temperature�...
-
Page 7: Automatic Operation
NETWORKER WALL CONTROL OPERATION AUTOMATIC PRE-WET AUTOMATIC PRE-WET When the Cooler is turned ON, with both the fan and the pump in either Auto or Manual mode, the Cooler will start a Pre- Wet automatically. The Pre-Wet stage ensures the pads are thoroughly wet before the fan starts. This prevents warm air When the Cooler is turned ON, with both the fan and the pump in either Auto or Manual mode, the Cooler will being initially blown into your home and contributes to the effective operation and performance of the Cooler. The Pre-Wet start a Pre-Wet automatically�... -
Page 8: Manual Operation
NETWORKER WALL CONTROL OPERATION NETWORKER WALL CONTROL OPERATION MANUAL OPERATION MANUAL OPERATION MANUAL OPERATION Manual operation enables you to control the fan, its speed, and the pump manually. Manual operation enables you to control the fan, its speed, and the pump manually. Manual operation enables you to control the fan, its speed, and the pump manually. -
Page 9: Setting The Time & Day
If the pump is going to be used, adequate ventilation (openings) need to be provided to prevent condensation build up. SETTING THE TIME & DAY Ensure the Networker is turned OFF using the ON/OFF button (1). 2. Press Key 5 (18 - Clock) and the screen will display the message “Clock setting mode”, and then the Digital Clock (19) will flash. Use the Rotary Dial (7) to select the right time. 4. Press Key 1 (14 -Day) until the correct day appears e.g. Mon (20). -
Page 10: Coded Messages
Press either the ON/OFF button (1) or the PROG button (5)� The Brivis Networker remembers the last setting and the next time you select the Timer it will go to that same setting� CODED MESSAGES CODED MESSAGES While the Brivis Networker is operating your system, it is also monitoring and controlling every aspect of the While the Brivis Networker is operating your system, it is also monitoring and controlling every aspect of the system’s system's performance. - Page 11 LOCKING THE BRIVIS NETWORKER To prevent any unwanted alterations being made to the coolers settings, the Brivis Networker can be locked via a 4- digit PIN code. In the case of dual Brivis Networkers, if one is locked the other is also locked. If dual Brivis Networkers are installed, the user PIN codes can only be set at the Master Brivis Networker. The Slave Brivis Networker can only lock and unlock the system and cannot access the PIN codes.
- Page 12 NETWORKER WALL CONTROL OPERATION NETWORKER WALL CONTROL OPERATION ZONING ZONING Some systems may include multiple Coolers with each operating in a different zone area. Zone keys (28) will Some systems may include multiple Coolers with each operating in a different zone area. Zone keys (28) will appear on the appear on the screen and these will have been set up and explained by the installer where required� ZONING screen and these will have been set up and explained by the installer where required.
-
Page 13: Care And Maintenance
CARE & MAINTENANCE The unit is not cooling very well • Check the water supply tap is turned on at the Cooler • Check the pump has been selected on the wall control. • Check sufficient door and/or windows have been opened. Refer to exhaust requirements covered in “Before Operating Your Evaporative Cooler. There is no air coming out of some vents •... - Page 14 Check and lubricate all moving parts. • On Brivis Contour Series and some Advance Series models, ensure the ServoSeal damper mechanism is opening and closing correctly. Please note that to maintain your warranty, the above servicing needs to be conducted by an authorised person trained in the service of Brivis Coolers.
- Page 15 A. Evaporative cooling relies on doors and/or windows being open so you can run it when you are not home, provided you have the required ventilation openings Q. How much water does the tank of my cooler hold? Model Tank Capacity (litres) Brivis Contour Series L36, L46, L56, L66, L76 Brivis Promina P36, P46, P56, P66, P76 Brivis Advance Series...
- Page 16 Q. Why doesn’t my evaporative cooler turn on when the current time and room temperature is displayed yet the word ‘COOLER’ is not? A. Your evaporative cooler has lost communication with your Networker wall controller, a service call is required. Q.
-
Page 17: Warranty
WARRANTY TERMS OF WARRANTY – AUSTRALIA Rinnai Australia Pty. Ltd. ABN 74 005 138 769, 100 Atlantic Drive, Keysborough VIC 3173. NOTICE TO CONSUMERS UNDER AUSTRALIAN CONSUMER LAW Our goods and services come with guarantees that cannot be excluded under the Australian Consumer Law� For a major failure with a good, you are entitled to a replacement or refund and compensation for any other reasonable foreseeable loss or damage. -
Page 18: Terms Of Warranty
WARRANTY TERMS OF WARRANTY 2�1 Subject to the Terms of Warranty set out in this document, effective from the date of purchase by the Purchaser, the Product is warranted to be free from defects in materials & factory workmanship for the period set out in table below: PRODUCT GROUPS PARTS... -
Page 19: Conditions Of Warranty
WARRANTY CONDITIONS OF WARRANTY 3�1 The Purchaser may only obtain the benefit of the Warranty if the Purchaser: a) maintains and has the Product serviced in accordance with the instructions set out in the service section of the relevant Service or Owner’s Manual; b) complies with clause "7 Purchaser’s Responsibilities"... -
Page 20: Purchaser's Responsibilities
WARRANTY LIMITATIONS 5�1 Third parties are often involved in providing advice to consumers about the climate control solutions best suited to the consumer’s needs. Any advice or recommendations given by such parties, including advice about Product fitness for purpose and overall system design, sizing and application are not the responsibility of Rinnai. - Page 21 PLUM TRADE SERVICES ABN 45 125 909 677 | AU29119 Unit 4, 22-30 Wallace Avenue, Point Cook, Victoria 3030 PO Box 6014, Point Cook, Victoria 3030 Tel: (03) 8360 9622 | (03) 5292 2219 Monday to Friday, 9.00 am to 5.00 pm EST. Saturday, 9.00 am to 1.00 pm EST. For further information visit www.plumheatcool.com.au or email contact@plumheatcool.com.au...
Need help?
Do you have a question about the Brivis Contour Series and is the answer not in the manual?
Questions and answers