Subscribe to Our Youtube Channel
Summary of Contents for Lynxspring TSD 10
- Page 1 10” T���������� D������ U��� G���� 2900 NE Independence Ave ©2022 Lynxspring, Inc. Lee’s Summit, MO 64064 All Rights Reserved sales@lynxspring.com Revised 3/9/2022 1 (877) 649-5969 10” Touchscreen Display www.lynxspring.com...
- Page 2 T���� �� C������� 1. BOX CONTENTS 2. INSTALLATION GUIDE 2.1 Power Supply & Ethernet Connec� ons 2.2 Moun� ng Op� ons 2.3 Procedure 2.4 Tamper Screw Detail 3. GETTING STARTED 3.1 Powering up the Display 3.2 Restar� ng the Display 3.3 Display Start up 3.4 Se�...
- Page 3 1. B�� C������� 1. 10” Android Tablet with J TEQ Kiosk Applica� on Preloaded. 2. Fully Enclosed Bezel (2 Parts Back and Front) 3. USB to Ethernet Adaptor 4. Right Angled Type C OTG Cable 5. Power Supply with UK and EU wall plugs 6.
- Page 4 2.3 Procedure 1. Secure the rear bezel metalwork to the wall or panel in the chosen loca� on, ensuring an opening matching the cut-out area on the bezel is available for cable access. 2. Make the wiring connec� ons to the tablet display.
- Page 5 3.2 Restar� ng the Display Once running the Lynxspring applica� on, the display can be restarted at any point by making a single press to the power bu� on . The power bu� on is located on the top of the display and is accessible using an Allen key provided in the kit.
-
Page 6: Display Setup
3.3 Display Setup During the start up process, the following screens will be observed. No user input is required at this point. 3.4 Se� ng the Locale When the Display starts for the fi rst � me, or there are no historical se�... - Page 7 4. C��������� �� � S����� 4.1 Making a Connec� on to a DHCP Router This secti on describes the process connecti ng to a network with DHCP. If a Stati c IP connecti on is required, go to either secti on 4.3 for Stati c Ethernet or 4.4 For Stati c WI-FI , then return to secti on 4.2. If there are no historical se�...
- Page 8 WI-FI Connec� on Only A connec� on to the network should now be present. Click Next. 4.2 Manage and Display Content The applica� on will now search and fi nd all sources available on the network. Once search and discovery is complete, the Networks and Content Sources confi...
- Page 9 Select the desired Source by clicking on the blue arrow. This will add it to the content to be displayed. Any number of sources can be selected, or if desired, the same source can be selected numerous � mes, with a diff...
- Page 10 Collapse the input box to save the se� ngs. Repeat the previous steps for each source to be added. To reorder, press and hold the drag and drop handle found on the right of each saved source, then drag up or down.
-
Page 11: General Settings
To remove a source, swipe le� from the center and click the remove bu� on. This only removes this reference to the source. It remains available in the device list. Op� on Sources can also be added manually, by using the ‘Add Source Manually’ bu�... - Page 12 Once the content has been selected and setup, click Preview. A� er clicking Preview, content from the top of the list is displayed. A preview bar is displayed providing easy access back to the confi gura� on screen If more than one source has been chosen, then an addi�...
- Page 13 4.3 Connect to an Ethernet Source with Sta� c IP When connected by Ethernet to the source and there is no DHCP available, the Connecti on Type dialog box is displayed. Click on ETHERNET. Click on Ethernet in the Networks and Content Sources page and then Ethernet again in the Wireless &...
- Page 14 Enter network se� ngs for Sta� c Ethernet connec� on. A value must be added to each fi eld before the se� ngs can be saved. IP Address: Netmask: DNS1: is is same as gateway. Gateway: Connect Next Click and then to fi...
- Page 15 4.4 Connect to an WI-FI Source with Sta� c IP When the Connecti on Type dialog box is displayed. Click on WIFI. Select the network to join. Selected network MUST password protected for Advance Op� ons to be visible. Click on Advanced Opti ons then drop the IP Setti ngs...
- Page 16 Scroll the entry box down and enter the network se� ngs for Sta� c Ethernet connec� on. A value must be added to each fi eld before the se� ngs can be saved. Scroll to the top of entry box and ensure the password is entered and all the confi...
- Page 17 Any sources already connected to the same network will be found. Add the content to be Preview displayed and then launch the pages using preview as per the methods described in Secti on 4.2.
- Page 18 5. G������ S������� Various Display se� ngs can be confi gured by selec� ng General Setti ngs accessed from bu� on in the top bu� on in the top le� -hand corner or by swiping from the le� edge of the screen. The following can be confi...
- Page 19 5.2 Wi-Fi Switch Disabling Wi-Fi. By default, this is on. This toggle switch is specifi cally designed if your connected via an ethernet cable for the convenience to turn off Wi-Fi completely. 5.3 Adjus� ng the Dimming Behavior The dimming func� on can be adjusted by the following: •...
- Page 20 5.5 Reset the Display The display can be restored to factory se� ngs using the RESET DISPLAY bu� on. This process will reset all the se� ngs in the General Se� ngs page to default. It will clear all network se�...
- Page 21 Installa� on of a Client Cer� fi cate to 10” Touchscreen Display 1. Insert a microSD card with the Cer� fi cate loaded into the card slot on the tablet. The fi le should be in the root directory. Other fi...
Need help?
Do you have a question about the TSD 10 and is the answer not in the manual?
Questions and answers