Tower Hobbies Cat Condo Quick Start Manual

TOWER Cat Condo

read first

REVIEW BEFORE
ASSEMBLY
• Designed for hand assembly.
No tools required.
• Check regularly to ensure all
components are connected.
• Place finished unit in an area
with room for cats to play and
interact with all features.

CARE INSTRUCTIONS

• Spot clean fabric and frame with
• Do not immerse in water
or place near high heat or
open flame. • Supervise pet interaction with
• Regularly check the stability of
all connections of components.
a
1

To form the BASE (pt.1),

you will need these pieces:
P RTS N ME QTY
3C
3-Way Corner ( 3 )
4 C 4-Way Corner ( 3 )
5C
5-Way Corner ( 2 )
A35 Long Tube ( 10 )
Foam Pads ( 8 )
c
1
When building sections
Then you will need these pieces:
with fabric pieces,
insert tubes into the
P RTS N ME QTY
sleeves of the fabric
first, then add the
4 C
4-Way Corner ( 1 )
connectors.
5 C 5-Way Corner ( 3 )
6C
6-Way Corner ( 2 )
A35
Long Tube ( 7 )
G
Play Floor ( 1 )
G2
Escape Floor ( 1 )
a
2
Assemble the base (pt.2), and
add it to base (pt.1) to form the
complete base unit.

To form the BASE (pt.2),

you will need these pieces:
P RTS N ME QTY
2 S
2-Way Straight ( 1 )
3 S
3-Way Straight ( 4 )
3 C
3-Way Corner ( 2 )
4 C
4-Way Corner ( 1 )
5C
5-Way Corner ( 1 )
A35
Long Tube ( 7 )
A 6
Short Tube ( 4 )
B28
Short Curve ( 2 )
Foam Pads ( 6 )
c
2
REMINDER: Insert tubes into the
fabric first, then add connectors.
To form the 1st floor HIDEAWAY
DEN, you will need these pieces:
P RTS N ME QTY
3 S
3-Way Straight ( 2 )
4 C
4-Way Corner ( 4 )
A35
Long Tube ( 2 )
A 6
Short Tube ( 6 )
B3
Long Curve ( 4 )
L3 Hideaway Den ( 1 )
a moist towel. Allow to air dry
thoroughly.
the product. Inspect for wear.
Replace when worn.
Lay the components out on the floor,
then insert tubes into connectors to
assemble the base (pt.1).
connectors & parts
2S 3 S 3C
(2 pcs) ( 16 pcs)
A1 A35
Sisal Post Long Tube
A16
(3pcs) (56pcs)
Short Tube
(18pcs)
L3
L2
Hideaway Den
Hideaway
(2pcs)
Penthouse
(1 pcs)
1
Self-adhesive foam pads
(if used) should be placed
on the underside of all
eight connectors.
Secure the velcro sleeves around the
horizontal tubes. Across the center (from G1
to G2), wrap the velcro flap across the tube
and secure it to the matching velcro strip.
2
Self-adhesive foam pads
(if used) should be placed
on the underside of six
connectors, as illustrated.
After the hideaway den is assembled, add it
to the base, and secure the velcro sleeves
around the horizontal tubes at top
and bottom as shown.
4 C 5 C
( 7 pcs) (18 pcs) ( 9 pcs)
B31
G1
B28 Long Curve
Play Floor
Short Curve (16pcs)
(1pcs)
(8pcs)
D2 H
Hideaway Corner (1pcs) Hammock Floor (1pcs)
b
To begin the 1st floor, you will
need these pieces:
P RTS N ME QTY
A35
Long Tube ( 5 )
A Sisal Post ( 1 )
•
b
Assemble the unit, then
add it to the base.

To continue the 1st floor,

you will need these pieces:
P RTS N ME QTY
4 C
4-Way Corner ( 1 )
5 C
5-Way Corner ( 1 )
A35
Long Tube ( 4 )
A Sisal Post ( 1 )
•
6 C
Foam footer pads
(14pcs )
( 2 pcs)
M1
G2 Square Plush Mat
Escape Floor
(1pcs)
(1pcs)
M2
Corner Plush Mat
(1pcs)
S1
Ramp (1pcs)
M3
Rectangle Plush Mat
(2pcs)
Add the assembled
unit to Step 1b.