Sealey CP20VCHS Quick Start Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instructions protection
1. SAFETY
WARNING! Read all safety warnings, instructions, illustrations and specifications provided with this tool. Failure to follow all
‰
instructions listed below may result in electric shock, fire and/or serious injury.
WARNING! Disconnect the saw from the battery unit before changing accessories, servicing, performing any maintenance or storing.
‰
1.1. GENERAL SAFETY
Maintain the saw and battery to ensure they are kept in good condition. Check for alignment or binding of moving parts and any
‰
other condition that may affect the power tool's operation. If damaged, have the tool repaired before use.
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Ensure the saw is switched off before installing the battery pack.
9
Keep the saw clean for best and safest performance.
9
Dress properly. Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the tool e.g. wood may contain nails, screws etc.
9
Keep work area clean and well lit.
9
Keep children and bystanders away while operating a power tool.
9
Ensure battery pack is correctly inserted into the tool handle and latched in place before attempting to switch it on.
9
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Stay alert, watch what you are doing and use common sense when operating a power tool.
9
DO NOT operate the tool when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
Prevent unintentional starting. Ensure the switch is in the off position before connecting the battery pack, picking up or carrying
9
the tool.
Remove any adjusting key or wrench before turning the tool on.
9
Use personal protective equipment. Always wear eye protection, (standard spectacles are not adequate).
9
DO NOT over reach. Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
8
Keep children and unauthorised persons away from the working area.
9
Keep tool and charger in the case and store in a safe, dry, childproof area where the temperature will not exceed 104°F (40°C).
9
Store idle power tools out of reach of children and DO NOT allow persons unfamiliar with the power tool or these instructions to
9
operate the power tool.
Use power tool and accessories in accordance with these instructions, taking into account the working conditions and the work
9
to be performed.
Keep handles and grasping surfaces clean and free from oil and grease.
9
DO NOT force the tool. Use the correct power tool for the application.
8
DO NOT use the tool if the switch does not turn it on and off.
8
DO NOT use the tool where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT allow children to operate the tool.
8
DO NOT operate the tool if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT hold unsecured work piece in your hand.
8
DO NOT leave the tool operating unattended.
8
DO NOT carry the tool with your finger on the power switch.
8
DO NOT use the tool for a task it is not designed to perform.
8
DO NOT get the tool or battery charger wet or use in damp or wet locations.
8
1.2. CHAINSAW SAFETY
Keep all parts of the body away from the saw chain when the chain saw is operating. Before you start the chain saw, make sure the
9
saw chain is not contacting anything. A moment of inattention while operating chain saws may cause entanglement of your clothing
or body with the saw chain.
Always hold the chain saw with your right hand on the rear handle and your left hand on the front handle. Holding the chain saw with
9
a reversed hand configuration increases the risk of personal injury and should never be done.
Hold the chain saw by insulated gripping surfaces only, because the saw chain may contact hidden wiring or its own cord. Saw
9
chains contacting a "live" wire may make exposed metal parts of the chain saw "live" and could give the operator an electric shock.
© Jack Sealey Limited
20V 25CM CORDLESS CHAINSAW - BODY
ONLY
MODEL NO:
Wear protective Wear head
gloves protection
Original Language Version
CP20VCHS
Wear ear Wear protective
protection clothing
Wear safety Wear face mask
footware
CP20VCHS Issue 1 24/09/21