Summary of Contents for SMITH SYSTEM 58040
- Page 1 Assembly Instructions MOTUM MOBILE LECTERN MODEL NUMBERS 58040 and 58041 Document #: 179720 Revised: 2/2022...
- Page 2 Document #: 179720 Revised: 2/2022...
- Page 3 Hardware And Components ITEM NO. PART NO. DESCRIPTION P14310 MWS TD LOCK ASSEMBLY P14304 MOBILE LECTERN TO U ASSEMBLY P14295 MSW LEG ASSEMBLY LEFT P14296 MSW LEG ASSEMBLY RIGHT P14314 MOBILE LECTERN DOOR HINGE ASSEMBLY P14307 MOBILE LECTERN PED TO LEG BRACKET ASSEMBLY P14374 MWS TD TILT SUPPORT ASSEMBLY P14510...
- Page 4 Hardware And Components Item No. Part No. Description P14322 NO. 10 X 5/8” TORX BUTTON HEAD SCREW P14324 NO. 10 X ½” TORX SELF DRILLING BUTTON HEAD SCREW P14323 10-32 X ½” TORX BUTTON HEAD W/ PATCH P13977 M6 X 1.0 X 20MM SOCKET HEAD, HEX DRIVE, BLK OX P13994 M6 X 1.0 X 10MM SOCKET HEAD, HEX DRIVE, BLK OX P13995...
-
Page 5: Panel Guide
Panel Guide 58041 – Left Hand Mobile Workstation 58040 – Right Hand Mobile Workstation Document #: 179720 Revised: 2/2022... - Page 6 General Assembly Guidelines • Ensure that all components are accounted for and undamaged before assembling • Follow each step carefully to ensure the proper assembly of this product • 2-person assembly is highly recommended • Clean the product with a mild cleaner and damp cloth Tools •...
- Page 7 Assembly Instructions Unpack and confirm all parts are present. There are 2 panels (BB), one will attach to assembly (#3) and the other to (#4). Begin by placing one panel (BB) on smooth, clean, surface, facedown with pilot holes facing up. Position leg assembly (#3) with holes aligned (as shown) and attach using 4x fastener [#1].
- Page 8 Assembly Instructions 3. Insert support assembly (#8) into cut-out in panel (X). Using 4x washer [#9] and 4x fastener [#2], loosely finger tighten (#8) into place. Align latch (#9) with pilot holes on panel (X) and attach using the 2x shorter fasteners (included in latch packet).
- Page 9 Assembly Instructions 4. Align assemblies (#3) and (#4) to assembly (#2) making sure the back edges are snug and that the flange on bracket (#2) slides between panel (BB) and corner brackets on (#3) and (#4) (as shown in Detail: A below). Attach assembly (#2) to 2x panels (BB) using 6x fastener [#1] Document #: 179720 Revised: 2/2022...
- Page 10 Assembly Instructions 5. Use 6x fastener [#1] to attach (#3) and (#4) to (X) (as shown in Detail: B). 6. For left hand unit – Attach hinge (#5) to (#3) using 2x fastener [#1]. Do not fully tighten. For right hand unit – Attach hinge (#5) to (#4) using 2x fastener [#1]. Do not fully tighten. Please note on hinge orientation , the horizontal slot should be on top, and the vertical slot should be on bottom when installing .
- Page 11 Assembly Instructions 7. Insert panel (AA) between (#3) and (#4), aligning top edges. Attach to (X) using 3x fastener [#1]. 8. Gently insert panel (Y) into assembly from the side. Tip to position panel under tabs on (#3) and (#4) as shown below.
- Page 12 Assembly Instructions 9. Using 8x fastener [#3], attach part (#6) to (#3) and (#4) from bottom. 10. Attach panel (V) to assembly (#6) using 12x fastener [#1]. Document #: 179720 Revised: 2/2022...
- Page 13 Assembly Instructions 11. Lay unit on its back on a smooth, clean surface. Place 4x fastener [#1] in the remaining brackets on (#3) and (#4) and tighten. 12. Place butterfly plate (#10) with tape facing down on a smooth, clean surface.
- Page 14 Assembly Instructions 13. Carefully insert column through unit. Attach to bracket (#7) from bottom using 3x fastener [#4]. 14. Firmly insert provided casters. With casters in locked position, set unit upright. Document #: 179720 Revised: 2/2022...
- Page 15 Assembly Instructions 15. Assemble lock and attach to door. Attach latch strike plate (#9) to door using 2x longer screws provided with latch kit (#9) 16. Attach door panel (CC) to hinge (#5) using 2x fastener [#1] utilizing the top and bottom holes in hinge. Make necessary adjustments for proper alignment of door before attaching self- drilling fastener [#2] through center hole.
- Page 16 Assembly Instructions 17. Place panel (W) on butterfly plate (#10). While pressing right button, push down on panel (W) until it makes contact with the top of (#2). 18. Remove backing from tape strips on butterfly plate (#10). Next, align unit with a vertical surface such as a door.
- Page 17 Assembly Instructions 19. While applying pressure to panel (W), press right lever to raise lift mechanism fully. Using 4x fastener [#1], attach top (W) to butterfly plate (#10) while applying pressure from above. 20. Attach lift handles and cable clips [#6] to underside of top (W) using 4x fastener [#1].
Need help?
Do you have a question about the 58040 and is the answer not in the manual?
Questions and answers