Download
Share
Print this page
  1. Manuals
  2. Brands
  3. HydroHoist Manuals
  4. Sports & Outdoors
  5. HydroPort PRO
  6. Installation manual

HydroHoist HydroPort PRO Installation Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
INSTALLATION
MANUAL
HydroPort PRO
915 W. Blue Starr Dr. Claremore, OK 74017
Rev. - 1/12/2015
1-800-825-3379
2003265 Rev A

Advertisement

loading
Need help?

Need help?

Do you have a question about the HydroPort PRO and is the answer not in the manual?

Questions and answers

Summary of Contents for HydroHoist HydroPort PRO

  • Page 1 INSTALLATION MANUAL HydroPort PRO 915 W. Blue Starr Dr. Claremore, OK 74017 Rev. - 1/12/2015 1-800-825-3379 2003265 Rev A...
  • Page 2 AC GROUND FAULT CIRCUIT INTERRUPTER (GFCI) DEVICE WHICH IS TO BE USED IN SERIES WITH THE USER’S PRIMARY AC POWER SOURCE. THE GFCI IS AN INTEGRAL PART OF THE HYDROHOIST BOAT LIFT AND IS DESIGNED TO OFFER A LIMITED MEASURE OF PROTECTION TO THE USER AGAINST HAZARDOUS ELECTRICAL CONDITIONS OR SHOCKS SHOULD THEY OCCUR.
  • Page 3 HydroHoist Marine Group Model: HydroPort PRO CONTENTS Getting Started - Section 1 Assembly - Section 2 Installation - Section 3 Operating Instructions - Section 4 Trouble Shooting - Section 5 Parts List - Section 6...

  • Page 4: Getting Started

    Getting Started HydroHoist Marine Group Model: HydroPort PRO Sec. 1 Pg. 1 Getting Started Assembly can be done on land, trailer, or water. Assembly Platform A list of tools needed for hoist assembly is given below. In addition to these, tools for boat Tools dock preparation, dock bumper removal, etc.
  • Page 5 Assembly HydroHoist Marine Group Model: HYDROPORT PRO Sec. 2 Pg. 1 Assembly Instructions Notes: Steps 1.1-1.3 are already done on purchased unit. Step Procedure Insert the Bow Bumper [2] into the Main Body by inserting the barbed feature on the bottom side of the Bow Bumper [1] into the hole on the Main Body and pushing down until it is firmly seated.

  • Page 6: Installation Instructions

    Installation HydroHoist Marine Group Model: HYDROPORT PRO Sec. 3 Pg. 1 Installation Instructions Rigid Dock Step Procedure Assemble upper [5] and lower [8] mooring brackets together loosely, then slide the assembly onto the HP PRO at mooring location Holding the Bottom Plug [9] into the HP PRO Assy as shown, run the SS Connecting Bolt [1] and SS Flat Washer through the Top Plug [3] and thread into Bottom Plug [9] .
  • Page 7 Installation HydroHoist Marine Group Model: HYDROPORT PRO Sec. 3 Pg. 2 Installation Instructions Universal Dock Step Procedure Holding the Bottom Plug [5] into the HP PRO Assy as shown, run the SS Connecting Bolt [1] and Flat Washer Through the Top Plug [4] and Mooring Link-Universal [4] and thread into Bottom Plug. Tighten bolt until top and bottom plugs are in contact with main body.
  • Page 8 Installation HydroHoist Marine Group Model: HYDROPORT PRO Sec. 3 Pg. 3 Installation Instructions Rigid Mount Floating Dock Only Step Procedure Drill four 3/8” holes into dock face and attach the Extended Hinge Mooring Plate [1]. If using the HD Dock Brack- et [4] with Hinge Mooring Plate holes will only need to be drilled if using thru-bolt method of dock bracket connec- tion.
  • Page 9 Installation HydroHoist Marine Group Model: HYDROPORT PRO Sec. 3 Pg. 4 Installation Instructions Rigid Mount Step Procedure When attaching the Mooring Bracket-Rigid in side mount application make sure your Upper Mooring Brackets (4150180) are oriented as shown. It is recommended to bolt the front Mooring Bracket-Rigid about 1” down from neutral (neutral is defined as: where the link is positioned without a craft on it) and the rear Mooring Bracket-Rigid down 1”...
  • Page 10 Installation HydroHoist Marine Group Model: HYDROPORT PRO Sec. 3 Pg. 5 Installation Instructions Universal Dock– Fixed or Floating Docks Step Procedure Attach the Universal Dock Bracket [1] to the dock as shown (3 different kits are illustrated). NOTE: IT IS UP TO THE INSTALLER TO DETERMINE IF THE ATTACHMENT IS STRONG ENOUGH.
  • Page 11 Installation HydroHoist Marine Group Model: HYDROPORT PRO Sec. 3 Pg. 6 Installation Instructions Connecting Units Step Procedure Assemble parts as shown below. There will always be a top and bottom link in the middle and just a bottom link at the front.
  • Page 12 Installation HydroHoist Marine Group Model: HYDROPORT PRO Sec. 3 Pg. 7 Installation Instructions Connecting Units Step Procedure Tighten the plugs on the side that is left unattached to the point that the bottom of the plugs are flush with the bot- tom of the Connecting Links.
  • Page 13 Installation HydroHoist Marine Group Model: HYDROPORT PRO Sec. 3 Pg. 8 Strap Hook Installation NOTE: Fig R. TEMPORARY ATTACHMENT. CUSTOMER IS RESPONSIBLE FOR PROVIDING SECURE ATTACHMENT.
  • Page 14 Operating Instructions HydroHoist Marine Group Model: HYDROPORT PRO Sec. 4 Pg. 1 Operating Instructions Loading ( WARNING Only load PWC when HP PRO is unoccupied 1. Approach HP PRO at idle speed only. 2. Position bow of PWC up against Keel Guide.

  • Page 15: Troubleshooting

    Trouble Shooting HydroHoist Marine Group Sec. 5 Pg. 1 Model: HYDROPORT PRO Trouble Shooting I can’t get my PWC to stay on the HP PRO when I pull on to the platform CONDITION: A.) You are coming in to fast CAUSE: B.) The PWC’s weight is to far to the rear of the craft.

  • Page 16: Parts List

    Parts List HydroHoist Marine Group Model: HYDROPORT PRO Sec. 6 Pg. 1 Parts List Part # Qty. Part # Qty. Parts Box - Rigid Mooring (6918121) Kit Box - Universal Dock (6918110) Nut - Hex - 3/8" Galv 2090107 Connec"ng Link - Fixed Dock 4150060 Nut - Hex - 1/2"...