Summary of Contents for AndyMark TEKTRAY
- Page 1 Installation, Usage Tips, & Warranty Information AndyMark, Inc. TekTray - 700 E. Firmin St., Kokomo, IN 46902 (765)868-0932...
-
Page 2: Bill Of Materials
1/4-20 x 1.5 inch FHCS (Flat Head Cap Screw) 1/4-20 COLLAPSIBLE NUT (Gray and bronze color) 1/4-20 x 1 inch SHCS (Socket Head Cap Screw) 1/4-20 NYLOCK NUT 1/4-20 x 3/4 inch SELF-TAPPING SCREW AndyMark, Inc. TekTray - 700 E. Firmin St., Kokomo, IN 46902 (765)868-0932... -
Page 3: Tools Needed
9. A 10 ft. x 10 ft. cleared flat surface is recommended for rail assembly. Step 1 Preliminary Items and Suggestions 1.1. Ensure all parts are included in your TekTray packages (one long box, one large flat box) as listed on the Bill of Materials. 1.2. Inspect all items for shipping damage 1.3. - Page 4 2.5 Tighten the 5/16 screws to nuts so the RISERS are at right angles to the CROSS TUBE (6). 2.6 This assembled portion of rail structure is now called RISER/CROSS TUBE. Align these holes Step 2.1 Step 2.1 Step 2.2 Step 2.6 Step 2.3 AndyMark, Inc. TekTray - 700 E. Firmin St., Kokomo, IN 46902 (765)868-0932...
- Page 5 Various hole mounting locations may need to be tried to find the best fit in the truck bed. Repeat step 3.3 for LEFT RAIL using the same corresponding holes. Step 3.3 Step 3.2 RISER/CROSS TUBE & RAIL LAYOUT Step 3.4 AndyMark, Inc. TekTray - 700 E. Firmin St., Kokomo, IN 46902 (765)868-0932...
- Page 6 STATUS CHECK: Each RISER is fastened to a RAIL with two (2) 1/4-20 x 1 inch SHCS (two per RISER). The RISER, CROSS TUBE, RAIL ASSEMBLY (aka: RAIL ASSEMBLY) is complete. AndyMark, Inc. TekTray - 700 E. Firmin St., Kokomo, IN 46902 (765)868-0932...
- Page 7 FOOT tightly against the truck bed side wall. 6.5 Close the tail gate, ensuring clearance between RAIL end and tail gate face. Step 6.2 Step 6.1 Step 6.4 AndyMark, Inc. TekTray - 700 E. Firmin St., Kokomo, IN 46902 (765)868-0932...
- Page 8 7.4 Slide the RIGHT RAIL (3) toward the interior of the truck bed 7.5 Using the 7/16” drill bit, drill through the left truck bed post where marked in 7.3. Step 7.1 Step 7.1 Hole Step 7.5 Step 7.3 AndyMark, Inc. TekTray - 700 E. Firmin St., Kokomo, IN 46902 (765)868-0932...
- Page 9 STATUS CHECK: Both RAILs are fastened to back truck bed posts. The front ends of each RAIL not to be fastened to the truck bed sides. Verify the outside to outside RAIL dimension is 59.5” after RAIL fasteners have been installed. AndyMark, Inc. TekTray - 700 E. Firmin St., Kokomo, IN 46902 (765)868-0932...
- Page 10 RISER feet are all fastened to truck bed floor, by means of 2 screws each. TIP: The RISER foot plate can be bent to form to the ribs in the truck bed. AndyMark, Inc. TekTray - 700 E. Firmin St., Kokomo, IN 46902 (765)868-0932...
-
Page 11: Install The Tray
STATUS CHECK: ASSEMBLED TRAY should glide freely on RAILs, moving with 5-7 pounds of push force. Ensure TRAY easily locks with both pins in front and rear locking positions. AndyMark, Inc. TekTray - 700 E. Firmin St., Kokomo, IN 46902 (765)868-0932... - Page 12 Step 10.2 Step 10.6 STATUS CHECK: END OF TRAVEL STOPS will now limit Tray from being removed from RAILS and from hitting the front bed wall. TekTray is fully installed. AndyMark, Inc. TekTray - 700 E. Firmin St., Kokomo, IN 46902...
-
Page 13: Usage Tips
• Never move a vehicle without making sure the TRAY is locked in front or rear position. The TekTray concept and design is protected by U.S. Patent # 7111887 AndyMark, Inc. TekTray - 700 E. Firmin St., Kokomo, IN 46902... - Page 14 AndyMark, Inc. guarantees that this product is free from defect in workmanship and materials from three years of the date of the purchase of product. AndyMark, Inc will not be responsible for any defect which has resulted from normal wear, misuse, lack of maintenance, or alteration made or specifically authorized by anyone other than authorized service centers or installation centers.
Need help?
Do you have a question about the TEKTRAY and is the answer not in the manual?
Questions and answers