Download Print this page

Vac - Alert VA-2000 Installation Instructions Manual

Safety vacuum release system

Advertisement

Quick Links

Safety Vacuum Release System
Installation Instructions
Model VA-2000
Vac-Alert
Industries, LLC
TM
th
775 8
Court, Suite 4
Vero Beach, FL 32962
www.vac-alert.com
April 29, 2011

Advertisement

loading

Summary of Contents for Vac - Alert VA-2000

  • Page 1 Safety Vacuum Release System Installation Instructions Model VA-2000 Vac-Alert Industries, LLC 775 8 Court, Suite 4 Vero Beach, FL 32962 www.vac-alert.com April 29, 2011...
  • Page 2 SVRS unit. NOTE: The Model VA-2000 type is indicated on the outside of the box and on the unit itself. Make sure you have the correct Model SVRS for...
  • Page 3 SVRS testing. Using the vacuum gauge on the Model VA-2000, note the level of the operating vacuum. If the vacuum level exceeds 15” Hg, system adjustments to lower the vacuum level will...
  • Page 4 SVRS, you are providing an important layer of protection against dangerous body and limb entrapment situations. This system is not an effective defense against hair entanglement. This device may mitigate evisceration. The Model VA-2000 SVRS unit shall only be installed in...
  • Page 5 conjunction with an ASME/ANSI A112.19.8-2008a or VGB 2008 approved suction fitting(s), or an approved channel drain system at each suction outlet or drain outlet. For newly constructed pools or spas where two or more suction outlets are employed, it is important that the outlets be separated by three feet, with minimum 2-1/2”...
  • Page 6 SVRS installation. Turn off all pump motors and select the best location for SVRS installation. SVRS LOCATION 1. Locate the SVRS on the main drain suction line, between the main drain and the main drain line isolation valve. Install the SVRS away from the pump suction (12”...
  • Page 7 PUMP START-UP TEST 1. At this point, the pump start-up vacuum level for the system needs to be determined. Close the SVRS vent by pushing down on the reset lever. Use the vacuum gauge on the installed SVRS unit to read the pump start-up vacuum level in the main drain line.
  • Page 8 in the hole at the vent end. Push the Vac-Alert piston towards the adjustment end until the lockout mechanism is engaged. A clicking sound is heard when the lockout mechanism is engaged. 2. Remove the security cap from the adjustment end (white end with Vac-Alert embossing on body) utilizing the spanner tool shipped with the unit.
  • Page 9 SVRS TESTING With the pump turned on, fully primed, all air bled from the filter, and with suction piping valves set to divert all flow from the main drain…( turn off skimmers and all other ports of suction except the main drain line). 1.
  • Page 10 end (gray end) surface. A screwdriver can be used to press this screen into final position. Care must be taken to avoid bending or crushing the vent screen. Each SVRS unit is provided with a Vac-Alert Field Test Data Sheet that must be completed.
  • Page 11 SVRS device to ensure proper adjustment of the unit. The Vac-Alert Model VA-2000 SVRS unit must be tested at the start of each swimming season, and recommended thereafter at least once per month while the pool or spa remains in use by the end user.
  • Page 12 3. The internal main body of the Model VA-2000 SVRS unit is not designed for field repairs. The unit must be routinely tested as detailed herein, and a unit not operating properly should be reported immediately. The following external parts may need replacement over time depending upon environmental exposure and use: a.
  • Page 14 ������������������������������� ����������� ����������������� �������������� ��� � ������������ ������������������������� ��� � ��������������������������������������������� �� ������������� ���������������������������������������������� ��� � ���������������������������������������� ������������������������������������������� ������������������� ��� � ������������������������������������������� ��� � ��������������������������������������� ���������������� ����������������������������������������� ����������������������������� ����� ������������� ����������������������������������������������� �� � ����������������������������������������������������������� ���������������������������������������������������������������� ��������������������������������������������������������������� ������������������������� ���������������������������������������������������������������� �������������������������������������������������������������� �� ����������������������...
  • Page 15 ������������������������������� ����������� ����������������� �������������� ����� � �������������������������������������������������������� �������� ������������� ��� � ���������������������������������������������������������� ���������������������� ����������������������������������������������������������� ���������������������������������������������������������� ����� � ����������������������������������������������������� ��������� ����������������������������������� ��� � ������������������������������������������������������������ ����� � ����������������������������������������������������� ������������������������������������������������������ ��� � ��������������������������������������������������������� ������������������������������������������������������ ���� ����������������������������������������������������������������� ������������������������������������������������ ����������������������������������������������������������� ������������������������������������������������� ������������������������������������������������������� ������ � ����������������������������������������������������� �����������������...
  • Page 17: Installation Location Information

    VAC-ALERT FIELD VA-2000 INSTALLATION DATA SHEET 1-800-374-7405 A copy of this installation form MUST be mailed or faxed to Vac-Alert Industries, LLC within 10 days of installation to maintain all product warranty. Mail to: Vac-Alert Industries, 336 West College Ave, Santa Rosa, CA 95401 or fax to (707)-576-8286.