Table of Contents
Advertisement
Quick Links
TORO-I
Quick installation and programming guide
This quick guide is a summary of the complete installation manual. The manual contains safety warnings and
other explanations which must be taken into account. The most recent versions of this guide and the
installation manual are available at the "Downloads" section on Erreka's website.
http://www.erreka-automation.com
WARNING
The options and functions described in this guide apply for the firmware version indicated on the circuit. The
firmware, as part of a process of continuous improvement, is subject to new functionalities or upgrades being
included as a result of new versions which are not necessarily compatible with previous ones. For this reason,
some options or functions may differ or be unavailable if your firmware is older than shown in this guide.
SG.C
SG.C
Assembly levels (mm)
SG.C
ELECTRICAL WIRING:
Element
A: Main power supply
B: Flashing light
C: Photocells (Tx / Rx)
D: Pushbutton/wall key
E: Antenna
C295B
Elements of the complete installation
Photocells
SG.A: opening photocell,
SG.C: closing photocell,
SG.C
SG.A
E295A
Nº wires x section
2
3x1.5mm
2
2x0.5mm
2
2x0.5mm
/ 4x0.5mm
2
2x0.5mm
Coaxial cable 50k (RG-58/U)
English
enable: C410
enable testing: C411
enable: C510
enable testing: C511
enable with opening
disabled: C520
enable testing with
opening disabled: C521
Maximum
length
30m
20m
2
30m
50m
5m
7
Advertisement
Table of Contents
Summary of Contents for Gerreka TORO-I
- Page 1 TORO-I Quick installation and programming guide English This quick guide is a summary of the complete installation manual. The manual contains safety warnings and other explanations which must be taken into account. The most recent versions of this guide and the installation manual are available at the "Downloads"...
- Page 2 Unlocking 1 Turn the cover (1). 2 Insert the key (2) and turn it clockwise without forcing it (the cylinder will be pushed out a few millimetres by the spring). 3 Operate the handle (3) by turning it 180º to the left. The gate can now be operated manually.
- Page 3 Turning direction change and check (C1) 1 Press ENTER, with the display showing rSXX Â 8, rSº â 8, (rSº ENTER ENTER ENTER ENTER rS8º rS8º ? , etc). P274J P274I P274K P274H ENTER ENTER ENTER ENTER ENTER P274ZZ P274Y P274X P274W P274V...
- Page 4 Total opening radio code programming P1 (with RSD receiver only, C801) If a receiver other than RSD 1 Press ENTER, with the used, display showing rSXX corresponding instructions. Â 8, rSº â 8, rS8º (rSº rS8º ? , etc). Select the option C801 ENTER ENTER...
- Page 5 Complete programming chart Parameter Preset option Options or values Motor turning direction and limit switches configuration Type of gate Sliding gate Opening safety device (photocell or Device not installed strip) Device without testing Device with testing Closing safety device (photocell or Device not installed strip) Device without testing...
- Page 6 Flashing light No pre-warning, static output With pre-warning, static output 0...5. 0...9 59 = 59 sec.; 2.5 = 2 min. 50 sec., etc Garage light time Gate speed 1...9 01: minimum speed (40Hz); 02: 45Hz, 03: 50Hz, 04: 55Hz, ... 09: maximum speed (80Hz) Slowdown speed 1...9...
Need help?
Do you have a question about the TORO-I and is the answer not in the manual?
Questions and answers