Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for BERGHOF B-Fortis CC-Slim Series
- Page 1 USER MANUAL 1.2 B-Fortis CC-Slim series...
- Page 2 This equipment handbook is only complete in conjunction with the product-related hardware and soft- ware manuals required for the specific application. You can contact us at: Berghof Automation GmbH Arbachtalstrasse 26 72800 Eningen Germany T +49.7121.894-0 F +49.7121.894-100 Email: controls@berghof.com www.berghof-automation.com Berghof Automation GmbH is certified to DIN EN ISO 9001:2015.
- Page 3 Version Date Description 06/09/2019 Initial version 08/05/2020 Conversion to catalogue numbers and adaptation to S-number sys- 18/06/2020 Formatting revised in the document 05.03.2021 Dual Core versions added Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com...
-
Page 4: Table Of Contents
Real-time clock ........................... 16 microSD card............................16 Summary of features .......................... 16 ASSEMBLY ............................17 CONNECTION ........................... 18 5.1. Power supply ............................ 18 5.1.1. Connecting the power supply ......................19 Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... - Page 5 STANDARDS AND CERTIFICATES ....................55 11.1. Standards ............................55 11.2. Declaration of conformity ........................ 55 CUSTOMER SERVICES / ADDRESSES ..................56 12.1. Customer services ........................... 56 12.2. Addresses ............................56 Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com...
- Page 6 USER MANUAL 1.2 | B-FORTIS CC-SLIM SERIES APPENDIX ............................57 13.1. Notes on copyright and the software licence ................57 13.2. List of figures............................ 57 Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com...
-
Page 7: General Information
Individual instruction or list of instructions which can be carried out in any order. … List of instructions which must be carried out in the order given. … Additional product information Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 8: Hazard Categories And Indications
Failure to observe the safety measures may result in minor injuries. Take preventive measures. NOTICE Possible damage to property Failure to observe the safety measures may result in damage to property. Take preventive measures. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 9: Qualified Personnel
→ The user is responsible for coordinating the use of the safety-related control components with the responsible authority and for adhering to its specifications. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 10: Intended Use
During installation, make sure that the existing seal profiles are undamaged. For operation, refer to the applicable ambient conditions (see “Technical data”). Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 11: Transport And Storage
If you notice any damage in transport or the contents do not match the order: inform the suppliers immediately. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 12: Safety
Disconnect the device from the system. Do not open the device housing. If it is necessary to work on internal parts of the device, contact the manufacturer (see “Addresses”). Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 13: Product Description
The connections are located on the front of the device. Devices from this series are intended for instal- lation on a mounting rail in the control cabinet. All the connections are of the plug-in type. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 14: Overview Of B-Fortis Cc-Slim
RS-485 terminating resistor (120 Ohm) EtherCAT (ETH1) CAN terminating resistor (120 Ohm) RS-232 / RS-485 µSD microSD card connection (optional) CAN-Bus (CAN0) LEDs: PWR, Run/Stop, Error Debug interface Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 15: Scope Of Delivery And Accessories
USB thumb drive to be used for updating the application or for downloading data directly. USB thumb drives with FAT/FAT32 formatting are supported. If you require support for other USB formats, please contact our Technical Support team. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 16: Can Interfaces
1 or 2 CAN interfaces → 2 serial interfaces (1x RS-232; 1x RS-485). → 1 µSD card slot → Onboard I/O (digital and analogue) → Real-time clock Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 17: Assembly
2nd Push the device towards the mounting wall until the retaining spring snaps into place. The device is clamped on the mounting rail. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 18: Connection
All connections and cables should be set up in a way that prevents interference and capacitive interference to the device. Make sure that the current and voltage resistance of the supply cables are sufficient. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 19: Connecting The Power Supply
Power supply 24 V DC (-15%/+20%) (PLC internal processing) max. 1.2 A – The following counterparts have been tested for the SL-SMT 3.5 plug-in connector (Weidmüller), and may be used with the device: → BLZF 3.50/12/180 Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 20: Data Connections
Damage to the inputs or the device! Voltages above ±32 V can damage the inputs or the device. Do not apply a voltage exceeding ±32 V to the inputs. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... - Page 21 DO 1 digital output 1 DO 2 digital output 2 DO 3 digital output 3 DO 4 digital output 4 – Power supply (see “Power supply”) 9-12 Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com...
- Page 22 – Total current of all max. 2 A outputs Parallel switching of max. 1 A Maximum permissible value with a logical two outputs connection to increase power Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com...
- Page 23 Depends on the cycle time set in the program- ming system – Protection against reverse polarity – Potential isolation Status display One yellow LED per input Lights up at logical 1 Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com...
- Page 24 Fig. 7: Circuit diagram of the principles of positive switching, input Fig. 8: Operating ranges of digital inputs (type 1/3) Designation Designation “ON” range Transition range “OFF” range Signal-to-noise ratio < 1 V Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com...
-
Page 25: Counting Inputs (C)
Examples for counters: up/down; pulse/direction; encoder (A/B) Fig. 9: Counter up/down or pulse/direction Designation Designation Up, pulse, A (CNT0) Up, pulse, A (CNT1) Down, direction, B (CNT0) Down, direction, B (CNT1) Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... - Page 26 Supply voltage (24 V DC; GND) and the signals of the transmitters must go through the same → cable. → The PLC and the transmitter must use the same power supply. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com...
-
Page 27: Ethernet
Meaning according to IEEE 802.3 clause 25 LNK/RCV Yellow Link, Data Receive Flashing: connection active; data transfer in progress Off: no connection established SPEED Green On = 100 Mbit/s Off = 10 Mbit/s Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 28: Ethercat
Meaning according to IEEE 802.3 clause 25 LNK/RCV Yellow Link, Data Receive Flashing: connection active; data transfer in progress Off: no connection established SPEED Green On = 100 Mbit/s Off = 10 Mbit/s Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 29: Usb
Failures and malfunctions when connected directly to signal ground! Only use USB devices that do not have a direct connection between the signal ground and the hous- ing. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 30: Serial Interfaces
If the interface is located at the start or end of the bus topology: Set switch S3 to ON in order to switch on the 120 Ω terminating resistor. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... - Page 31 For electrically isolated interfaces with connections to the reference ground at one point: link to GND. Where necessary, provide an attenuated link to GND (e.g. via 200 Ω) at multiple points. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com...
-
Page 32: Can Bus
Set switch S2 to ON in order to switch on the 120 Ω terminating resistor between CAN_L and CAN_H. For Baud rates, settings and cable lengths, comply with the recommendations of CiA-303-1. Example: at 1 Mbit, max. 25 m Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 33: Analogue Inputs
Weidmüller B2CF 3.50/06/180(F) SN BK Fig. 17: Analogue inputs X2 Analogue inputs X2 Assignment Assignment AI1 (U/T) AI3 (U/T) AGND AGND AI2 (U) AI4 (U) Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 34: Data From Analogue Inputs
The filtering can be activated and configured using CODESYS V3. The sampling rate is constant. It can only be filtered with a whole multiple of the sampling rate. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 35: Operating Modes For The Analogue Inputs
-15 V, a fault bit (FAULTN/FAULTP) is set in the process image which can be read by the user program. – Input type Asymmetrical voltage metering (single-ended) – Reference potential AGND Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... - Page 36 The value in degrees Celsius is calculated from the resistance value and linearised (6th degree polynomial) – Input type 2-wire measurement or 3-wire measurement – Reference potential AGND Dynamic properties Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com...
- Page 37 Analogue filtering Second-grade low- pass filter; cut-off fre- quency 650 Hz – Greatest temporary 1% of measuring deviation during range electrical error test- ing according to IEC 61131-2 Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com...
- Page 38 Do not connect to the common GND. The required connections can already be found on the cir- cuit board. Cables to the analogue sensors/encoders should be connected as directly as possible (avoid the use of terminals and terminal blocks). Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com...
- Page 39 The nearest AI (U) connection is used to compensate the resistance in the cable. It can only be used directly in conjunction with the following AI (U/T) channel. Channels 1 and 2, and also channels 3 and 4 each form a pair for 3-wire measurement. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com...
-
Page 40: Operation
The device does not have an on/off switch. The device starts automatically when the system is switched on or the power is connected. Switching off The device is switched off when the system is switched off or the power supply is disconnected. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 41: Initial Start-Up Of The Network
The login window is displayed. Fig. 20: Login window Log in with the following login information: Name: admin Password: admin The web configuration page will be displayed. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... - Page 42 Click on “Reboot” in the web interface and then confirm on the next page by clicking on “Reboot Module”. The device is configured and ready for use. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com...
-
Page 43: Operation
While the Run/Stop light is flashing yellow: the device is in use and must not be switched off. During the boot process, the device does not give any warnings via the LEDs. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 44: Start/Stop
The battery is not designed to be changed by the user; the manufacturer should be contacted in order to change the battery. For batteries according to UN 3091-PI 970 Section II Button Cell, further information according to the manufacturer's PSDS/MSDS applies. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 45: Microsd Card
The operating life of the gold-plated contacts is up to 10,000 plugging and unplugging cycles. The microSD card drive has a push-in/push-out insertion and ejection mechanism. To avoid malfunction, the microSD card may not be removed by pulling. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 46: Troubleshooting
Correct the network settings and make a note of them. Restart the device. Maintenance mode is turned off automatically. The device is configured and ready for use. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 47: Servicing / Maintenance
Make sure all the ventilation openings are kept free of obstructions Do not open the device. If it is necessary to work in the device, contact the Service department. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 48: Disassembly
2nd Pull the device at the bottom away from the mounting rail. Push the device upwards and remove from the mounting rail. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 49: Disposal
Dispose of electronic scrap in accordance with the national laws and regulations. Make sure that the battery is completely discharged. Dispose of batteries at a recognised collection point in accordance with national laws and regula- tions. Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 50: Technical Data
DIN EN 60715:2001, 35 x 7.5 mm Certification to product standards DIN EN 61010-2-201, DIN EN 61131- Touch operation CODESYS V3 (IEC 61131-3) Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... - Page 51 1x host USB 2.0 / USB plug port A No. plugging/unplugging cycles max. 1,000 CAN bus interfaces No. / type of interface 1x to 2x CAN-Bus Protocols CAN-Bus and/or CANopen master Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com...
- Page 52 Battery Type Panasonic VL2020 or similar Operating life 10 years (depending on operating temperature) Storage 1 year without voltage (any longer and RTC data can be lost) Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com...
-
Page 53: Type Plate
Date of manufacture (year/week) CE mark Supply voltage and maximum current Disposal information rating manufacturer’s ad- Manufacturer’s logo Manufacturer dress) QR code (identification no.) MAC addresses of device Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 54: Device Variants And Identification
Fig. 27: Options label Extensions for tooling and debugging → USB-to-Ethernet adapter order number: S-02040101-0000 → USB to WLAN adapter EasyConnect order number: S-02040102-0000 Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 55: Standards And Certificates
Products ➔ Controllers/PLC ➔ Display PLC ➔ Resistive ➔ Product A link to download the declaration of conformity can be found on the product page: Fig. 28: Download menu Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... -
Page 56: Customer Services / Addresses
Ostendstraße 196 90482 Nürnberg Germany info@ethercat.org www.ethercat.org Beuth Verlag GmbH, 10772 Berlin, Germany VDE-Verlag GmbH, 10625 Berlin, Germany VDE Verlag GmbH, 10625 Berlin, Germany Internet research: www.iec.ch Berghof Automation GmbH | Arbachtalstrasse 26 | 72800 Eningen | Germany | www.berghof-automation.com... - Page 57 → → FreeType License (FTL) The source code for the free software can be requested from Berghof Customer Services at cost price within three years of delivery of the device. 13.2. List of figures Fig. 1: Overview of B-Fortis CC-Slim ......................14 Fig.
Need help?
Do you have a question about the B-Fortis CC-Slim Series and is the answer not in the manual?
Questions and answers