Garfield SWB08 Operator's Manual
  1. Manuals
  2. Brands
  3. Garfield Manuals
  4. Construction Equipment
  5. SWB08
  6. Operator's manual

Garfield SWB08 Operator's Manual

Dozer blade
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
DOZER BLADE
OPERATOR MANUAL
SWB
SWB
Models
SWB08
SWB09
Part Number
4350-2160-03

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SWB08 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Garfield SWB08

  • Page 1 DOZER BLADE OPERATOR MANUAL Models SWB08 SWB09 Part Number 4350-2160-03...
  • Page 3 INTRODUCTION READ THIS MANUAL carefully to learn how to operate and service your machine correctly. Failure to do so could result in personal injury or equipment damage. THIS MANUAL MUST BE CONSIDERED a permanent part of your machine and should remain with the machine when you sell it. MEASUREMENTS in this manual are given in both metric and customary U.S.
  • Page 4 ® Congratulations for acquiring a Garfield product . We are confident in your excellent decision to purchase Garfield equipment, and are honored to have you as our valued customer. Your dealership shall make the technical pre-delivery of your equipment, and a trained technician shall provide you maintenance and operation instructions contained in this manual.
  • Page 5 GENERAL INDEX INTRODUCTION GENERAL INFORMATION SPECIFICATIONS SAFETY RULES SAFETY DECALS OPERATION MAINTENANCE RECOMMENDATIONS SOLUTIONS FOR CERTAIN SETBACKS ASSEMBLY PARTS INDEX BOLT TORQUE CHART WARRANTY...

  • Page 6: General Information

    Tel. 01 (449) 922 47 66, 922 47 60 Fax 01 (449) 922 47 67 Dozer Blades SWB08 and SWB09, are designed to work safely, nevertheless, please consider the following: Read this manual carefully to understand proper handling and maintenance of your Dozer Blade.
  • Page 7 GENERAL INFORMATION Tecnomec Agrícola offers original spare parts through authorized dealers. Our trained personnel, is well versed on methods to service your equipment. If you need additional information or custom assistance, please contact your Bison authorized dealership or directly to TECNOMEC AGRÍCOLA S.A. DE C.V. YOUR AUTHORIZED DISTRIBUITOR TECNOMEC AGRÍCOLA, S.A.

  • Page 8: Inspection List

    INSPECTION LIST PRE-DELIVERY INSPECTION MADE BY BISON DEALERSHIP Once the Dozer Blade has been adjusted completely, check and ensure that it is ready for proper operation prior to deliver to customer. The following checklist is a reminder of checkpoints. Verify that each point is satisfactory and recheck, once all proper adjustments have been made.
  • Page 9 INSPECTION LIST DELIVERY BY BISON DEALERSHIP The following list is an important reminder to be transmitted directly to the customer at the moment the dozer blade is delivered. Check each point once it was duly explained to the customer. Point out to the Customer that useful life of this or any other machine is dependent of proper lubrication as described on its Operator's Manual.
  • Page 10 INSPECTION LIST POST-SALES INSPECTION It's advised that the following items are constantly checked during first hours of operation. Fully check the machinery and certify there are no damaged parts. Repair or change if necessary. Check there are no loose or missing screws. If possible, operate the hammer mill to verify it is functioning properly.
  • Page 11 SPECIFICATIONS SWB08 / SWB09 Dozer blade developed for pushing, backfilling trenches and levelling jobs in construction, public works, road maintenance, gardening, etc. The Dozer blade for skid steers has been designed with the most modern methods and built by skilled workers using quality materials.

  • Page 12: Safety Rules

    SAFETY RULES SAFETY RULES This is the safety-alert symbol which means ATTENTION! BE ALERT! YOUR SAFETY IS INOVOLVED! This safety alert symbol indicates important safety messages in this manual. When you see this symbol, carefully read the message below and be alert to the possibility of personal injury or death.
  • Page 13 SAFETY RULES PASSENGERS ARE NOT ALLOWED IN THE MACHINE Only the operator is allowed on the machine. Passengers on machine are subject to injury such as being struck by foreign objects and being thrown off of the machine. Passengers also obstruct the operator's view, resulting in the machine being operated in an unsafe manner.
  • Page 14 SAFETY RULES USE SAFETY LIGHTS AND ACCESORIES Slow vehicles, tractors, dragged or suspended equipment may present a risk to be transported or towed by road and hard to be seen, especially at night. Avoid injuries or death which may result from a collision with other vehicles. We recommend using lights and safety accessories when driving on public roads.

  • Page 15: Safe Maintenance

    SAFETY RULES CHECK THE HOSES FOR ANY DAMAGE: Hydraulic hoses fail due to physical damage, bends, weather and exposure to the weather. Periodically check the hoses. Replace damaged hoses. Avoid high pressure fluids: Fluids leaking under pressure can penetrate the skin causing serious damage.
  • Page 16 SAFETY RULES REMOVE PAINT BEFORE WELDING OR HEATING Avoid inhalation of fume or potentially toxic dust. Hazardous fumes can be generated when paint is heated by welding or when using a torch. You must do all work outdoors or in a well-ventilated area. Dispose all paint and solvent properly, when necessary.

  • Page 17: Operation

    OPERATION GENERAL INFORMATION Throughout this manual, reference is made to various blade components. The purpose of this page is to acquaint you with the various names of these components. This knowledge will be helpful when reading through this manual or when ordering service parts. Central Shaft Spring Pivot Box...

  • Page 18: Before Operating The Machine

    OPERATION SKID STEER PREPARATION 1. Wheel Spacing Important: To avoid possible damage from over stressing Skid Steer axles, use no tire combination which results in overall width greater than the width of the angle blade. Important: Before beginning operation, turn the wheel fully to the right and left to be sure there is sufficient clearance between the tires and the angling cylinders.

  • Page 19: Lubrication And Maintenance

    MAINTENANCE LUBRICATION AND MAINTENANCE ATTENTION: Being hit by the Dozer blade can cause serious injury or death ATTENTION: To prevent unexpected machine movement: Before lubricating, adjusting or servicing the machine connected to the machine (skid steer), check the following steps: 1.- Park the Blade on a flat surface.
  • Page 20 MAINTENANCE LUBRICATION: APPLY GREASE IN THE FOLLOWING PLACE: Apply grease in the indicated places at 16 hour intervals. Use a mechanical grease injector. 1.- Center pivot assy (one fitting grease) 2.- Hitch assy (4 fitting grease)
  • Page 21 MAINTENANCE 3.- Two fitting grease for each cilinder (6 fitting grease): 4.- Pivot box (two fittin grease):...
  • Page 22 RECOMMENDATIONS STORAGE AT THE END OF EACH SEASON PREPARATION FOR THE BEGINNING OF EACH SEASON The following storage procedure will help you to keep your blade in top condition. They will also help you 1.- Fully lubricate the machine according to the get off to a good start the next time your blade is Lubrication section.
  • Page 23 SOLUTIONS FOR CERTAIN SETBACKS PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION Cold oil. Warm oil with engine at idle Engine speed too slow. Open throttle. Blade angling or tilting too slowly. Restriction in diverter valve Clean or Replace Oil leaking past cylinder packings. Replace cylinder packings or cylinder new Check connection of electrical cables and if necessary Electrical cables for the manual control...
  • Page 24 ASSEMBLY 1.- The equipment arrives in a wooden structure protected with a plastic. 2.- Start by removing the protective plastic. 3.- Remove strap and woods upper part. 4.- With a forklift or crane, remove the blade assy from the wooden frame (using a sling). 5.- Cut the wires that support the ties to the wooden frame (use wire cutting pliers).
  • Page 25 ASSEMBLY 6.- Remove each of the white bundles (4 bundles wrapped with white protective material) 7.- Extract the hitch assy using a forklift and slings NOTE: be careful not to damage the hydraulic system (move it carefully). 8.- Extract the mounting bracket, using a forklift and a sling 9.- Place each of the assemblies or parts that you removed in a free and clean place, if necessary use...
  • Page 26 ASSEMBLY 10.- Remove the white protector from each assembly to facilitate handling, use a cutter to facilitate cutting. NOTE: Be careful not to cut yourself and do not cut or damage parts, hoses, electrical cable, etc. 11.- To start installing, place the “blade bracket” on wood as shown in the following image: 12.- Remove the “central shaft”, removing the “5/8”...
  • Page 27 ASSEMBLY 14.- Place the "hitch assy" on the "pivot box” 15.- Once the two assemblies are oriented, place the "central shaft" to join the two assemblies: Before inserting the entire "central shaft", orient the hole where the "5/8 hex screw" goes, this will facilitate the assembly.
  • Page 28 ASSEMBLY 17.- Place the "cylinder pin assy" to hold the "cylinder 3 x 8" on the "pivot box", also secure it with the ½” hex screw and ½” lockwasher, do the same on both sides (for both cylinders). 18.- The “hitch assy” must be fixed (vertical) without having to support it.
  • Page 29 ASSEMBLY 21.- Place the “mounting bracket” over the already assembled “hitch assy”, do it slowly until the two bases (of both assemblies) coincide. 22.- Since the two bases are in contact, slightly move the “mounting bracket” to the left to fit correctly and to put the piece "filling"...
  • Page 30 ASSEMBLY 24.- In order to install the 5/8” hexagonal screw that joins the “central pivot assy” with the “mounting bracket” and the “hitch assy” it is necessary to temporarily remove the “cylinder pin assy”. Do it very carefully to avoid damage! 25.- Insert the 5/8”...
  • Page 31 ASSEMBLY 28.- Take the piece "Cylinder 4 x 6" and remove the "Cylinder pin assy" to install cylinder: 29.- Place the "cylinder 4 x 6" according to the following image. 30.- Secure the cylinder through the “cylinder pin assy” and the ½” hex screw and ½” lock washer. 31.- Lay the hydraulic hoses according to the following picture.
  • Page 32 ASSEMBLY 32.- Extend the main hoses, to hold them with a "hose clamp", the hose must be held at a distance of 36 inches from the base of the valve, as shown in the figure: 33.- Tighten the hose clamp taking care not to damage the hose protector or the hose itself: 34.- Remove the 3/8”...
  • Page 33 PARTS INDEX DOZER BLADE SWB08 SWB09 MAIN STRUCTURE PARTS DIAGRAM LIST OF MAIN STRUCTURE PARTS HYDRAULIC SYSTEM PARTS DIAGRAM HYDRAULIC SYSTEM PARTS LIST...
  • Page 34 MAIN STRUCTURE PARTS DIAGRAM 36 33...
  • Page 35 LIST OF MAIN STRUCTURE PARTS SWB08 (QTY) REF. No. PARTE DESCRIPTION SWB09 (QTY) DB08020100W 8 BLADE ASSEMBLY DB09020100W 9 BLADE ASSEMBLY DB08020200W PIVOT BOX DB08020300W HITCH ASSEMBLY DB08010300W MOUNTING BRACKET DB08010400W CENTRAL SHAFT ASSEMBLY DB08010600W CYLINDER PIN ASSY DB08011000W CYLINDER PIN ASSY...
  • Page 36 HYDRAULIC SYSTEM PARTS DIAGRAM...
  • Page 37 HYDRAULIC SYSTEM PARTS DIAGRAM REF. No. PARTE DESCRIPTION SWB08 (QTY) SWB09 (QTY) 4110-4061-01 CYLINDER 4 X 6 X 2 4120-1159-50 ELBOW FITTING, 8ORBM-8JICM 90 4430-2492-48 HOSE, 6M3K-8JICF-8JICF-0.48 4110-1080-02 SOLENOID VALVE 4430-2492-84 HOSE, 6M3K-8JICF-8JICF-0.84 4430-2491-60 HOSE, 6M3K-8JICF-8JICF-0.60 4430-2493-00 HOSE, 6M3K-8JICF-8JICF-2.00 4120-1018-50...

  • Page 38: General Information

    TORQUE SCREW SPECIFICATIONS NON-METRIC BOLTS TIGHTENING SETTINGS (IN.) GENERAL INFORMATION Screw's Torque Values Always replace bolts with others of the same grade. Metric screws have the class number marked on the head. Tighten the screws according to the above table, unless the Operator's Manual indicates something different.
  • Page 39 TORQUE SCREW SPECIFICATIONS METRIC BOLTS TIGHTENING SETTINGS GENERAL INFORMATION Screw's Torque Values Always replace bolts with others of the same grade. Metric screws have the class number marked on the head. Tighten the screws according to the above table, unless the Operator's Manual indicates something different.

  • Page 40: Theft Prevention

    THEFT PREVENTION RECORD THE PRODUCT IDENTIFICATION NUMBER (P.I.N.) The Serial Number Plate of the "Dozer blade" is located in the "Mounting Bracket" part. Write the serial number in the space in the box that appears on the guarantees section. Mark the machine with your own unique system numbering.

  • Page 41: Limited Warranty

    LIMITED WARRANTY Please enter information below and save for future reference. AUTHORIZED DEALERSHIP: SALESMAN NAME: MACHINE MODEL: SERIAL NUMBER: END CUSTOMER NAME: PURCHASE DATE: PHONE NUMBER: ADDRESS: EMAIL: A. GENERAL PROVISIONS - The warranties described below are provided by Tecnomec Agrícola, S.A. de C.V. (TECNOMEC) to the original purchasers of new agricultural products from TECNOMEC or authorized dealers for a period of one (1) year under agricultural use.
  • Page 42 PART NUMBER 4350-2160-03 2012 Tecnomec Agrícola, S.A. de C.V. All Rights Reserved...

This manual is also suitable for:

Swb09

Table of Contents