Subscribe to Our Youtube Channel
Related Manuals for MasterForce 270-3282
Summary of Contents for MasterForce 270-3282
- Page 1 80V BRUSHLESS SNOW THROWER 270-3282 2600294ME SNB403 OPERATOR’S MANUAL CAUTION To Reduce The Risk Of Injury, User Must Read And Understand Operator’s Manual. Save These Instructions For Future Reference.
-
Page 2: Table Of Contents
TABLE OF CONTENTS Safety Symbols ......................Page 2 Safety Instructions ...................... Page 3 Overview ........................Page 7 Assembly ........................Page 9 Operation ........................Page 11 Maintenance ......................Page 13 Troubleshooting ......................Page 16 Exploded view ......................Page 17 Notes ........................Page 18 Warranty ........................ -
Page 3: Safety Symbols
SAFETY SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer. Symbol Name Designation / Explanation Volts Voltage Amperes... -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS The purpose of safety symbols is to attract our attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The symbol warnings do not by themselves eliminate any danger. The instructions and warnings they give are no substitutes for propper accident prevention measures. - Page 5 SAFETY INSTRUCTIONS R E A D A L L I N S T R U C T I O N S PREPARATION BEFORE USING (THIS POWER • Thoroughly inspect the area where the TOOL) power tool is to be used and remove all WARNING doormats, sleds, boards, wires, and other Read and...
- Page 6 SAFETY INSTRUCTIONS traffic. common cause of injury associated with • After striking a foreign object, turn the snow throwers. Never use your hand to machine off and remove the battery pack, clean out the discharge chute. To clear the and then inspect it for damage. Repair any chute: damage before restarting and using the •...
- Page 7 SAFETY INSTRUCTIONS applicable) except as indicated in the instructions for use and care. • Maintain or replace safety and instructions labels, as necessary. • Maintain Snow Thrower With Care – Follow instructions for lubricating and changing accessories. PROPOSITION 65 This product contains a chemical known to the state of California to cause cancer, birth defects or other reproductive harm.
-
Page 8: Overview
OVERVIEW Bail switch Chute control Safety switch Upper handle button Middle handle Lower handle Chute deflector Discharge Battery compartment chute Wheel LED lights Impeller Scraper SPECIFICATIONS Type Cordless, battery operated Motor 80V Brushless No-load Speed 1800 RPM Clearing Width 22 in. (55.9 cm) Clearing Depth 12 in. - Page 9 SPECIFICATIONS The recommended ambient temperature range: Item Temperature Snow Thrower storage temperature range 1.4 ˚F (-17 ˚C) ~ 113 ˚F (45 ˚C) S n o w T h r o we r o p e r a t i o n t e m p e r a t u r e 1.4 ˚F (-17 ˚C) ~ 113 ˚F (45 ˚C) range Battery charging temperature range...
-
Page 10: Assembly
ASSEMBLY UNPACKING INSTALL THE MIDDLE HANDLE FIG. 2 This product requires assembly. Middle • Carefully remove the product and any Lower handle accessories from the box. Make sure that handle all items listed in the package contents section are included. Knob •... - Page 11 ASSEMBLY INSTALL THE CHUTE DEFLECTOR WARNING • If the battery pack or charger is FIG. 4 damaged, replace the battery pack or the charger. • Stop the machine and wait until the engine stops before you install or remove Discharge the battery pack.
-
Page 12: Operation
OPERATION WARNING WARNING Wear eye Examine the work protection during operation area. Remove all stones, sticks, wire, bones, and other debris that can ricochet because of the rotating impeller. COLD WEATHER OPERATION STOP THE MACHINE The safe battery operation temperature rang- es from 1°F(-17°C) to 113°F (45°C). - Page 13 OPERATION ADJUST THE DISCHARGE CHUTE WARNING Release the bail FIG. 9 switch before you adjust the chute deflector. WARNING Do not push the Discharge trigger so far forward that a gap shows chute between the deflector and the chute. 1. Push and hold the trigger on the chute de- flector.
-
Page 14: Maintenance
OPERATION OPERATION TIPS If it is possible, clear the snow with the direction of the wind. • In strong winds, lower the chute deflector to direct the snow to the ground. • When you complete the work, let the machine operate for a while to prevent ice formation in the discharge chute. - Page 15 MAINTENANCE REPLACE THE BELT WARNING Make sure to FIG. 13 turn off the bail lever and remove the battery pack(s) before performing any maintenance task on your snow thrower. 1. Remove the 4 sets of nuts and bolts on the middle steel plate. 2.
- Page 16 MAINTENANCE STORE THE MACHINE • Clean the machine before storage. • Make sure the motor is not hot when you store the machine. • Make sure that the machine does not have loose or damaged parts. If it is necessary, do these steps/instructions: •...
-
Page 17: Troubleshooting
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION The handle is not in The bolts are not Adjust the height of the handle and make sure position. engaged correctly. that the knobs and bolts are aligned correctly. The machine does not The battery is not Charge the battery by following the procedures start. -
Page 18: Exploded View
EXPLODED VIEW ITEM NO. PART NO. DESCRIPTION R0201592-00 Impeller assembly R0200650-00 Scraper Kit R0201593-00 Wheel Assembly R0201594-00 Chute Deflector Assembly R0200908-00 Quick-Release Lever Assembly R0201595-00 Knob R0200654-00 PCB board R0200655-00 Skid plates Page 17... -
Page 19: Notes
NOTES Page 18... - Page 20 NOTES Page 19...
- Page 21 NOTES Page 20...
- Page 22 NOTES Page 21...
-
Page 23: Warranty
WARRANTY 4-YEAR LIMITED WARRANTY This MASTERFORCE™ brand power tool carries our famous No Hassle 4-Year Limited Warranty to the original purchaser. If, during normal use, this MASTERFORCE™ power tool breaks or fails due to a defect in material or workmanship within four (4) years from the date of original purchase, simply bring the tool with the original sales receipt back to your nearest MENARDS ®... - Page 24 © 2019 Menard, Inc., Eau Claire, WI 54703 12/2019 Page 23...
Need help?
Do you have a question about the 270-3282 and is the answer not in the manual?
Questions and answers