Subscribe to Our Youtube Channel
Related Manuals for Depaepe Premium 50
Summary of Contents for Depaepe Premium 50
- Page 1 Premium 50 USER MANUAL Depaepe Tel : +33(0)1 30 25 81 60 Fax : +33(0)1 39 98 61 24 www.depaepe.com Depaepe - Premium 50 SIP - User Manual v1.3 1/14...
-
Page 2: Table Of Contents
11 Declaration of conformity 13 ........................... arranty and after sales service 14 ........................Depaepe - Premium 50 SIP - User Manual v1.3 2/14... -
Page 3: Installation
Screw ST4 25 mm Phone starting The Premium 50 SIP comes with the DHCP mode selected. You can configure the phone only if this one acquired a dynamic IP address. So a DHCP server is required on the LAN. If necessary, download on internet a DHCP free software (e.g. “tftpd32”) and install on your PC to configure the Premium 50 SIP. Be sure that your PC is connected to the same VLAN with the phone. After the DHCP server allocated an IP address to the Premium 50 SIP, if you pick up the handset you can hear a tone. The configuration page can be accessed via your web browser by entering the phone IP address. If necessary, please consult your network administrator. To discover the phone IP address Lift the handset Hear the dial tone Press * 1 2 3 4 5 # Listen to the IP address being announced by the handset receiver Depaepe - Premium 50 SIP - User Manual v1.3 3/14... -
Page 4: Keypad Mapping
Figure 1 – Premium 50 SIP Keypad mapping Call Operations A. Initiating a call 1. Lift up the handset. 2. Listen to dial tone. 3. Press the desired number on the keypad and wait for 5 second or press “#” to dial out. 4. To end the call, place the handset back on the cradle in the base unit. B. Answering a call When there is an incoming call to the phone, an audible ringing sounds to alert the user and LED on the handset top flashes. 1. Lift up the handset to answer the call. 2. To end the call, place the handset back on the cradle. The LED will turn off. C. Redial 1. Lift up the handset. 2. Press REDIAL button. D. Ringer volume - Handset volume Depaepe - Premium 50 SIP - User Manual v1.3 4/14... -
Page 5: Call Flash
1. During a call, press the “FLASH” button. 2. The previous conversation is automatically put on-hold. 3. Wait for the dial-tone. 4. To transfer the call, simply press the desired number on the keypad and wait for 5 seconds or press "#" to dial out immediately. F. Call Hold 1. During a call, press the “HOLD” button. 2. The third party of the call is now put on-hold. Hold music is generated by the PBX to the other end. 3. To deactivate the call-hold, press the “HOLD” button again. G. Programmable Memory Button and Emergency Call Number 1) The Premium 50 SIP has 1 programmable memory button: the “MSG” button located above the keypad. To use this memory button, lift the handset and simply press it once. The number will be immediately dialed out. 2) The other corresponds to the preconfigured number for emergency call. To make an emergency call, lift the handset and wait for a predetermined number of seconds. The number will be automatically dialed out. Storing a number for hotkey and emergency call Go to the Web Portal (see page 8), go to the “Configuration” and “SIP / NAT Settings”. Depaepe - Premium 50 SIP - User Manual v1.3 5/14... -
Page 6: Message Waiting Lamp (Mwi)
2. Fill in the entries for Memory key, Emergency Call Number and Emergency Call Timeout (see below) 3. Remember to press save at the bottom of the page, when you are done. Figure 3 - Memory Key and MSG Key setting on Web Portal H. Message Waiting Lamp (MWI) When a message is received at the voicemail box, the LED on the back of the handset goes up and flashes periodically. The mailbox access number can be programmed to the memory key. Refer to Section G - Programmable Memory Key and Emergency Call. When it is configured properly, users can lift up the handset and press the memory key to access the mailbox. Depaepe - Premium 50 SIP - User Manual v1.3 6/14... -
Page 7: Web Portal
Web Portal The Premium 50 SIP Web Portal can be accessed by Google Chrome, Internet Explorer and Mozilla Firefox. A. To log in Enter http://< IP Address of the phone > on the browser. Login name and password are as follows, username : admin password : admin The welcome page shows the hardware version and firmware date code of the model (see below). Figure 4 - Welcome page of the Web Portal (A.1) Logout When done, remember to logout completely. Clear the cache / cookie of your web browser so that the previous login is not re-cycled by the next user. Depaepe - Premium 50 SIP - User Manual v1.3 7/14... -
Page 8: To Set Login Password For Web Portal
B. To set login password for web portal It is recommended for administrators to change login name and password to enhance security. Click on the “Admin” link at the top right corner of the page On the left panel, find the "Set Password" link and press on it. Enter username for login name Enter password and re-enter for confirmation purpose When the mask password box is checked, both password entries are masked. To un-mask, simply un- checked the mask password box. Figure 5 - Set Password for accessing the Web Portal Depaepe - Premium 50 SIP - User Manual v1.3 8/14... -
Page 9: Network Settings
C. Network settings Administrators may choose to operate in either dynamic IP environment and static IP environment. Go to Configuration page. On the left panel, click on the "Network / Print Log Settings" link After making changes, click save at the bottom of the page A pop-up window appears, you may choose between "back" and "restart" In order to have the changes take effect immediately, click "restart" You can always preserve the changes and decide to restart the phone at a later time Figure 6 - Network Settings page on Web Portal Depaepe - Premium 50 SIP - User Manual v1.3 9/14... -
Page 10: Sip Account Settings
D. SIP Account settings Parameters for Session-initiation-protocol (SIP) such as registrar address, proxy address, port etc. can be found in the "SIP Accounts" section on the Configuration page. Go to Configuration page On the left panel, under "SIP Accounts", click on the "Account 1" link Enter the SIP registration particulars for Account 1 Note that you have the flexibility of registering to one server per account When done, click Save The changes take effect immediately Proceed to complete the entries for Account 2 Figure 7 - Account Settings page on Web Portal Parameters for Call settings for each account can be found under the title, "Call Settings", on the left panel. Such parameters include: Call Forward Mode Call Waiting activation / deactivation DND (Do Not Disturb) activation / deactivation Auto-Answer activation / deactivation HIDE ID activation / deactivation. Reject anonymous activation / deactivation. Parameters for Audio settings for each account can be found under the title, "Audio Settings", on the left panel. Such parameters include: DTMF mode (in-band / RFC2833 / SIP INFO) SRTP Mode. Silence Supression. Jitter Packetization Time. Audio Codec preference (PCMU / PCMA / G.722 / G.729 / G.726 / iLBC) After, click on “Save”. E. Other settings Depaepe - Premium 50 SIP - User Manual v1.3 10/14... -
Page 11: Firmware Upgrade And User Configuration Backup / Restore
Go to Configuration page On the left panel, click on the "SIP / NAT Settings" link Enter the memory key number, message key number and NAT entries When done, click Save The changes take effect immeidately Figure 8 - Memory key and NAT settings page on Web Portal F. Firmware upgrade and user configuration backup / restore The firmware of the phone can be provisioned remotely. Administrators can do so easily on the Web Portal. Browsers that support this function include Internet Explorer and Mozilla Firefox. Go to the "Admin" page On the left panel, click on "Upgrade" link. See Figure 9 Click on "Choose File" button and browse for vmlinuz Click Upload A progress bar appears. See Figure 10. There may be some seconds when it temporarily disappears. Important: Do not unplug the power or Ethernet connection The whole progress takes approximately 55 seconds. When complete, the browse brings you to a new page and shows a confirmation. See Figure The phone power-cycles itself and comes back to run in the new firmware If the upgrade fails, disconnect the base from the Ethernet and re-connect it in order to trigger a power- cycle. Redo the firmware upgrade procedure. Depaepe - Premium 50 SIP - User Manual v1.3 11/14... -
Page 12: Declaration Of Conformity
Figure 9 - Firmware upgrade, User Configuration Backup / Restore on Web Portal Figure 10 - Firmware upgrade progress bar. Do not disconnect power or Ethernet cable Figure 11 - Firmware upgrade confirmation Declaration of conformity Depaepe - Premium 50 SIP - User Manual v1.3 12/14... - Page 13 Phone : +33 (0) 1 30 25 81 60 Address : 75-77 rue du Pré Brochet Fax : +33 (0) 1 39 98 61 24 Locality : SANNOIS Postal code: 95110 Product identification: - Family : Telecommunications Terminal Equipment - Type : IP/SIP Telephone set - Model : PREMIUM 50 SIP - Other information : compact phone We, Henri Depaepe SAS, hereby declare that this product is in conformity with the essential requirements and other relevant provisions of the R&TTE directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity, as well as the harmonised standards : For health and safety : ………………..……………. EN 60950-1 : 2006 For electromagnetic compatibility : …….……. EN 55022 : 2006 +A1 : 2007 Class B and EN 55024 : 1998 +A1 : 2001 +A2 : 2003 For public communications network connection : ………………… TBR 37 (21) and TBR 38 Made in China This product complies with : - European Directive 2002/95/EC on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS). - European Directive 2002/96/EC on waste electrical and electronic equipment. (WEEE). This marking indicates this product should not be disposed of with other household wastes at the end of its working life to prevent possible harm to the environment or human health. Please contact your supplier, your local government office or our commercial department to dispose of it in an approved recycling centre. Depaepe - Premium 50 SIP - User Manual v1.3 13/14...
-
Page 14: Arranty And After Sales Service W
Out of warranty policy Depaepe Telecom does not warrant that these phones will perform perfectly with all the equipments available on the market. The warranty only applies if the product is installed and used as specified in this user manual and in particular with respect to the minimum and maximum electrical voltage and current specifications. This warranty shall be invalid if the product is damaged as a result of misuse, abuse, neglect, accident, exposure to improper electrical voltages or current, repair, alteration or maintenance by any person other than the Depaepe Telecom service facility. Depaepe will not warrant consequences due to “Acts of God” such as weather storms, floods, earthquakes, fires or firestorms or acts of war, riots, etc. Warranty and repair service Phone : +33 (0) 1 30 25 81 74. Products purchased from an installer or from a distributor should be returned to them to be forwarded to us. All products returns should be sent prepaid with a copy of our original delivery note or a copy of the original invoice for tracing purposes at the following address: SAS HENRI DEPAEPE 75/77 Rue du Pré Brochet BP 80107 95112 SANNOIS Cedex (France) Repaired or exchanged units will be shipped back at our own cost. In all other cases a repair cost estimate will be issued and repairs will be completed once accepted. Depaepe - Premium 50 SIP - User Manual v1.3 14/14...
Need help?
Do you have a question about the Premium 50 and is the answer not in the manual?
Questions and answers