Advertisement
4. OPERATING INSTRUCTIONS
F
WARNING! Before using the crane, ensure that you have read and understood Section 1 safety instructions and that
p
instructions 3.14 and 3.15 of Section 3 have been successfully completed.
4.1.
Close the release valve at the base of the ram by turning the valve tap clockwise.
4.2.
Put the handle into the pump socket and pump. The jib will then move - continue to pump until the jib reaches the required height.
4.3.
Connect the crane hook to the load using a suitable certified sling or support beam. Ensure that you are aware of the load weight
and have checked that it is within the capacity of the crane at the jib extension you are using. When removing engines ensure you
know the weight you are lifting and use only lifting points recommended by the vehicle manufacturer.
4.4.
Lift only directly above the load. FWARNING! DO NOT LIFT THE LOAD AT AN ANGLE.
4.5.
To lower load, VERY slowly turn release valve at base of ram anti-clockwise.
4.6.
The crane is not a transportation device but may be used to reposition the load ready for working on. Lower the load and jib as far as
possible before attempting to move the crane and load. Do not attempt to move in a sideways direction.
The crane is not designed to sustain the load indefinitely.
When you have positioned the load for working, fully lower the load onto a secure and suitable work surface, being fully aware of your
own and other persons locations in relation to the lowering load.
4.7.
When the load has been successfully lowered and secured, remove the lifting harnesses etc. and place the crane in a safe location, having
ensured that the ram is fully retracted.
5. MAINTENANCE
NOTE: The crane MUST be maintained in accordance with these instructions.
5.2.
Lubrication: Oil all working parts monthly.
5.2.1. The ram is filled with oil and should only require occasional topping up - DO NOT use brake fluid, as this will damage the hydraulic seals.
Proceed as follows:
5.3.
Inspection of crane before use: Before each use the crane must be inspected for leaks, damage, loose or missing parts.
5.3.1. The crane must be inspected immediately if it has been subject to an abnormal load or shock load. It is recommended that such an
inspection is made by the supplier’s authorised service agent.
5.3.3. The owner and/or operators must be aware that repair of this equipment will require specialised knowledge and facilities.
It is recommended that an annual inspection of the crane is made through the supplier’s authorised service agent.
5.4.
Storage: Always store crane fully closed so that jib is in its lowest position and ram is closed. Always keep the crane clean and dry.
6. OWNER’S/OPERATOR’S RESPONSIBILITIES
The owner and/or operator shall study these instructions and retain them for future use.
6.1.
Understanding instructions and warnings. The owner and/or operator shall understand the operating instructions and warnings before
operating the crane. Warning information must be emphasised and understood. If the operator is not fluent in English, the instructions
and warnings must be read to, and discussed with, the operator in the operator’s native language by the purchaser/owner, making sure
the operator understands the content.
6.2.
Damaged crane. If the crane appears to be damaged, badly worn, or operates abnormally IT MUST BE REMOVED FROM
SERVICE! It is recommended that necessary repairs be made by the supplier’s authorised service agent.
6.3.
Decommissioning. After years of normal wear, the crane will eventually come to the end of its safe serviceable life. If, and when,
this happens, ensure that the hydraulic oil is drained off and disposed of in accordance with local authority regulations.
6.4.
Test Certificate. In accordance with the requirements of the UK Health and Safety Executive, a test certificate is supplied with this
crane. The test certificate is valid for one year from the date of first placing the crane into use. Your insurance company will want to
have a copy of the test certificate for their file. Additional copies of the test certificate can be purchased within one year of the date
of supply. If you need a copy please ask your dealer. After one year your insurance company has the right to request a re-test of the
crane. This is a chargeable service and can be obtained by contacting companies listed under “Lifting Gear” in Yellow Pages.
IMPORTANT: NO RESPONSIBILITY IS ACCEPTED FOR INCORRECT USE OF THE CRANE.
Hydraulic products are only repaired by local service agents. We have service/repair agents in all parts of the UK.
DO NOT RETURN PRODUCT TO US. Please telephone us on 01284 757500 to obtain the address and telephone number of your local agent.
If product is under guarantee please contact your dealer.
7. CRANE GUARANTEE
Your crane is guaranteed for one year from the date of purchase. The guarantee does not cover faults caused by incorrect use, lack of maintenance
or accidental damage, or damage caused to third parties through misuse. You are recommended to inform your insurers and check that
adequate cover is in place. Warranty claims must be supported by a copy of the dated receipt for the crane.
8. DECLARATION OF CONFORMITY
Folding Crane. Model PH20.V2
98/37/EC, Docks regulations 1934, 18a 22a EN292-2.
PH20.V2
Model No:
Serial No:
Batch No:
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name, address and postcode.
Sole UK Distributor,
Sealey Group, Bury St. Edmunds, Suffolk.
a) Use only good quality hydraulic jack oil available from your Sealey dealer.
b) Fully lower the jib extension arm.
c) DO NOT OVERFILL as this will cause failure.
d) After filling with hydraulic oil, pump the crane up to full height and pour off any excess oil.
Declaration of Conformity
here is in conformity with the following standards and directives.
Signed by Mark Sweetman
01284 757500
The construction file for this product is held by the Manufacturer and may be inspected, by a national
authority, upon request to Jack Sealey Ltd.
01284 703534
e-mail
We, the sole importer into the UK, declare that the product listed
11th August 2003
sales@sealey.co.uk
9A>
For Jack Sealey Ltd.
Sole importer into the UK
of Sealey Quality Machinery.
www.sealey.co.uk
PH20.V2 - 1 - 110803
Advertisement
