Table of Contents
Advertisement
Quick Links
P.O. BOX 11846 TUCSON, AZ 85734
(520) 294-3292
• FAX (520) 741-2837
www.iotaengineering.com
INSTRUCTION MANUAL
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed, including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
CAUTION – To prevent electrical shock, do not mate unit connector until installation is complete and A.C.
1.
power is supplied to the unit.
2.
CAUTION – This fixture provides more than one power supply output source. To reduce the risk of electrical
shock, disconnect both normal and emergency sources by turning off the A.C. branch circuit and by discon-
necting the unit connector.
3.
CAUTION – This is a sealed unit. Components are not replaceable. Replace the entire unit when necessary.
CAUTION – Installation and servicing should be performed by qualified personnel only. De-energize before
4.
opening.
The ILB-CP-HE-SD is for use with grounded LED luminaires listed to UL standards. Not for use in heated air
5.
outlets or hazardous locations.
6.
The ILB-CP-HE-SD requires an unswitched A.C. power source of 120 to 277 volts AC, 50/60Hz.
The ILB-CP-HE-SD and A.C. driver must be on the same branch circuit.
7.
8.
Do not mount near gas or electric heaters.
The ILB-CP-HE-SD should be mounted in locations and at heights where it will not readily be subjected to
9.
tampering by unauthorized personnel.
The ILB-CP-HE-SD will supply 10-60VDC output at the individual rated specification for 90 minutes. See indi-
10.
vidual units for output specifications.
11.
The ILB-CP-HE-SD is certified in the CA Title 20 Modernized Appliance Efficiency Database System (MAED-
BS) as a small battery charger.
12.
Suitable for installation in or on top of compartment spaces. Flexible conduit not needed for internal compart-
ment installation. For top mounting, use the TMK-80 accessory.
13.
Suitable for use in damp locations and enclosed and gasketed fixtures.
14.
Suitable for luminaires, recessed Type IC (intended for insulation contact).
15.
For use in 0° C minimum, 55° C maximum ambient temperatures.
16.
The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition, void
warranty, and result in non-compliance with UL specifications.
17.
Do not use this equipment for other than intended use.
18.
Install in accordance with the National Electrical Code and local regulations.
19.
Lighting fixture manufacturers, electricians, and end-users need to ensure product system compatibility before
final installation. See addendum for compatibility and covered luminaire requirements.
EMERGENCY LED DRIVER FOR USE
WITH LED LUMINAIRES IDENTIFIED
IN THE MANUFACTURER'S
E473237
ILB-CP-HE-SD
SAVE THESE INSTRUCTIONS
HIGH EFFICIENCY PERFORMANCE
MEETS CA T20 BATTERY CHARGER
EFFICIENCY STANDARDS
'B' MOUNTING DESIGN
HIGH EFFICIENCY EMERGENCY
LIGHTING EQUIPMENT
FOR LED
Patented. See iotaengineering.com/patents for more details
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for IOTAVX ILB-CP-HE-SD
- Page 1 CAUTION – Installation and servicing should be performed by qualified personnel only. De-energize before opening. The ILB-CP-HE-SD is for use with grounded LED luminaires listed to UL standards. Not for use in heated air outlets or hazardous locations. The ILB-CP-HE-SD requires an unswitched A.C. power source of 120 to 277 volts AC, 50/60Hz.
- Page 2 SD unit connector is disconnected. 1. FIXTURE The ILB-CP-HE-SD can be used with most LED loads that operate at 10-60 VDC. See the ILB Model Specification Chart for output specifications of the unit being installed. 1. The ILB-CP-HE-SD series has been evaluated to and found compliant to UL standard 924. The as-installed performance of system must meet or exceed all Federal, State, and Local code requirements.
- Page 3 OPERATION Normal Mode – A.C. power is present. The A.C. driver operates the LED load as intended. The ILB-CP-HE-SD is in the standby charging mode. The TBTS will be flashing green providing a visual indication that the battery is being charged, or solid green if the battery is fully charged.
- Page 4 For more information on diagnosing ILB-CP-HE-SD failure codes, contact Customer Service. Manual Testing - Manual Testing can be performed on the ILB-CP-HE-SD , provided the unit is fully charged, by press- ing and releasing the TBTS or engaging the wall switch that controls the emergency luminaire. Manual Testing cannot be initiated until the unit has received a full 24 hour charge.
- Page 5 CP Series Compatibility and Suitability of Use Guidelines Addendum (Rev.11042014) The purpose of this addendum is to sufficiently identify electrical compatibility and predictable emergency light output of the LED luminaire when used with the IOTA ILB-CP Series LED emergency drivers. Verification of these operating traits does not constitute a code-compliant, as-installed emergency egress system.
Need help?
Do you have a question about the ILB-CP-HE-SD and is the answer not in the manual?
Questions and answers