Table of Contents
Advertisement
Quick Links
User manual
LED BEAM 7 ZOOM
SAFETY INSTRUCTIONS
CAUTION!
Be careful with your operations. With a dangerous voltage you can suffer a dangerous
electric shock when touching the wires!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
For your own safety, please read this user manual carefully before you initial start-up.
Features:
15°-67° zooming,with 7*high MCD Ostar RGBW 4 IN 1 15W LEDs
DMX-512 connection / connection between fixtures
Occupation of the XLR-connection:
If you are using controllers with this occupation, you can connect the DMX-output of the
controller directly with the DMX-input of the first fixture in the DMX-chain. If you wish to
connect DMX-controllers with other XLR-outputs, you need to use adapter-cables.
Building a serial DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next
fixture. Always connect one output with the input of the next fixture until all fixtures are
connected.
Caution: At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a
120 resistor between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the
DMX-output of the last fixture.
Connection with the mains
Connect the device to the mains with the enclosed power supply cable.
1. DMX 512 protocol
Addressing
The LED DISPLAY on the rear side of the base allows you to assign the DMX fixture address,
which is defined as the first channel from which the item will respond to the controller. If you
set, for example, the address to channel 7, the item will use the channel 7 to 14 for control.
Please, be sure that you don't have any overlapping channels in order to control each item
correctly and independently from any other fixture on the DMX data link. If two, three or more
items are addressed similarly, they will work similarly. At DMX mode you can choose the
address from 1 to 512.After you connect the item to the mains, the item starts running. When
the item finishes resetting, A-OO1 will flash in the led display and then set the desired DMX
address by pressing the UP or DOWN buttons.
DMX Controlling:
After having addressed all items, you may now start operating these via your lighting controller.
After switching on, the item will automatically detect whether DMX 512 data is received or not.
Advertisement
Table of Contents
Summary of Contents for TECHTOP LED Beam 7 Zoom
- Page 1 User manual LED BEAM 7 ZOOM SAFETY INSTRUCTIONS CAUTION! Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when touching the wires! Keep this device away from rain and moisture! Unplug mains lead before opening the housing! For your own safety, please read this user manual carefully before you initial start-up.
- Page 2 DMX FUNCTIONS 16-channel mode 000 - 255 000 - 255 X-Fine 000 - 255 000 - 255 Y-Fine 000 - 255 XY SPEED 000 - 255 Dimmer(0-100%) 000 - 009 Shutter closed 010 - 245 Strobe effect slow to fast 246 - 255 Shutter open 000 - 255...
- Page 3 061 - 080 Internal program 3 081 - 100 Internal program 4 101 - 120 Internal program 5 121 - 140 Internal program 6 141 - 160 Internal program 7 161 - 180 Internal program 8 181 - 200 Empty 201 - 225 Motor Reset 226 - 255...
- Page 4 Reset Default .=OFF 10 rFAC .=ON Home Position Clear PAN and TILT Home 11 Ad t Setting Delt Position(3s) P(PAN) .=0-120 t(TILT) .=0-120 F(Gobo) .=0-120 12 rST Reset Motor Replacing the fuse If the fine-wire fuse of the device fuses, only replace the fuse by a fuse of same type and rating.
Need help?
Do you have a question about the LED Beam 7 Zoom and is the answer not in the manual?
Questions and answers