Page 1
2022-ON HYUNDAI SANTA CRUZ Thank you for purchasing a LOMAX STANCE Hard Cover. Agri-Cover, Inc. proudly ® manufactured this cover using superior quality materials and workmanship. With proper care, your cover will provide years of service and enjoyment. NOTICE TO INSTALLER: Even if familiar with product, read instructions prior to installation as improvements may be made without notice.
Page 2
PREPARATION IMPORTANT: Truck is equipped with a trunk-like lid on box floor. Lid remains functional, however, restricted from fully opening. Avoid forcing lid beyond its limit. COMPONENTS TOOLS NEEDED • (8) Clamps • Ratchet with 10mm and T-30 Torx sockets •...
PARTS DIAGRAM Front (closest to cab) Anchors Seal gasket Header bar Side seal Pivot link in clip Clamps (underneath) Cover assembly Retainment bracket Safety strap Latches on hole toward rear panel front of box Passenger side rail Rear Clamps Driver side rail...
Page 4
1: SIDE RAILS AND HEADER BAR INSTALL A. Use T-30 Torx socket to remove first, second and fourth bolts on both sides of Remove bolts truck bed and outer (2) bolts on bulkhead. NOTE: These bolts will be replaced with new hardware in Step 1B.
Page 5
1: SIDE RAILS AND HEADER BAR INSTALL (Continued) NOTE: For best adhesion, ensure air and surface temperatures are above 60° F. Side seal C. Ensure side of box is clean, wipe surface with alcohol pad. Apply side seal flush with top of bulkhead.
Page 6
1: SIDE RAILS AND HEADER BAR INSTALL (Continued) I. Starting at the front, adjust top of side rail until flush with top of box. Tighten 60mm bolts and clamp assemblies into factory holes. J. Verify side rail is level. If side rail is not level, perform one of the following: If side rail tilts up: loosen and lower clamp, engage teeth and then retighten clamp.
2: INSTALLING COVER A. At front of box, carefully place header panel on side rails. Hold cover’s rear edge 1” above side rails and slide cover hooks underneath front rail catch on each side. Cover hook underneath front rail catch B.
Page 8
2: INSTALLING COVER (Continued) CAUTION: Air and surface temperatures must be above 60° F for proper adhesion. D. Swing pivot links out from clips and attach anchors. Pivot link attached to anchor E. With anchor post toward cover, test placement on top of cab in flat area between ribs.
TROUBLESHOOTING PROBLEM SOLUTION • Top of tailgate hits cover when attempting Side rails are not level or set too low at to close rear of cover, raise rails at rear of box until cover no longer interferes with tailgate operation (see Step 1). Gap between cover and truck box or •...
Page 10
3: OPENING FOLDING COVER IMPORTANT: To avoid damage or misalignment of hinge points, open cover in a smooth, fluid manner. IMPORTANT: Remove debris or snow from hinges before opening cover. A. Open tailgate, pull release latch. B. Fold panel toward the cab. C.
Page 11
CLOSING FOLDING COVER IMPORTANT: To avoid damage or misalignment of hinge points, close cover in a smooth, fluid manner. Avoid dropping or slamming cover. IMPORTANT: Remove debris or snow from hinges before closing cover. A. Open tailgate. Release pivot link and lower onto side rails.
Page 12
REMOVING AND REINSTALLING COVER REMOVE COVER A. With cover open, detach safety straps from side rails. B. Pull release latch on header panel and lift rear edge of cover 1” above side rails (Figure Safety strap C. Slide cover back to disengage hooks, then carabiner lift to remove (Figure 2).
Page 13
ALWAYS PROPERLY SECURE COVER WARNING: Failure to execute these steps may result in severe damage and will void your warranty. 1. Cover hooks engaged underneath rail catches. 2. Latches engaged in retainment brackets. 3. Safety straps attached to side rails. 4.
SAFETY INFORMATION • Always ensure hooks and latches fully engage side rails. • Ensure safety straps are attached to side rails when cover is installed. • Ensure anchors are clear, free of interference. • Never rest cover against cab after installation. •...
INSPECTION AND MAINTENANCE The operator can perform most inspection and maintenance. It may be necessary to review the installation and operating instructions. • Periodically check and retighten safety strap hardware. If safety straps are damaged, replace with new hardware. • Periodically check and retighten clamps as needed.
MANUFACTURER’S LIMITED WARRANTY Agri-Cover, Inc. extends the following three (3) year Limited Warranty for the LOMAX ® STANCE Hard Cover: Agri-Cover, Inc. warrants a period of three (3) years from the date of manufacture that its LOMAX STANCE Hard Cover is free from defects in workmanship under normal use for ®...