Summary of Contents for Yanmar i8350
- Page 1 Electronic Control System Operation Manual for SY Series Engines with GEN III Controls ELECTRONIC CONTROL SYSTEM MANOPSY3M01 REvISION 3.2...
- Page 2 We reserve the right to make any change at any time without notice. Yanmar and are registered trademarks of Yanmar Co., Ltd. in Japan, the United States and/or other countries. Safety alerts alone cannot eliminate the hazards that they signal. Strict compliance to these special instructions when performing installation, operation, and maintenance is the most effective accident prevention measure along with exercising care and using common sense when performing such actions.
-
Page 3: Table Of Contents
Engine Diagnostic Codes ........................2 Maintenance Warning ..........................2 Power Reduction Mode ..........................2 Diagnostics ..............................3 System Alarms ............................3 i8350/55 Operation ............................4 Appendix A: i5601E Digital Display Setup .....................15 Display Settings ............................6 Menus .................................6 User Settings and Factory Settings ......................7 “Unlocking” the Hot Keys .........................7 Quad Screen Parameters ..........................8... -
Page 4: System Overview
The i5601E displays real-time data as well as warnings or alarms for any engine abnormality. Diagnostic codes will be stored for future reference by a Yanmar technician. Shift & Throttle Control Head CP67601: Trolling Switch (Optional) The Shift &... -
Page 5: Start Up
When the signal loss problem has been corrected, you must shut the engine off and restart to return throttle control back to the shift/throttle control head. For Emergency Shift see transmission manual. Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls © Yanmar 2008 Page 3... -
Page 6: I5601E
In the unlikely event that an engine fault occurs, a warning box appears in the display showing the cause of the fault, and the action to take, "Press Any Key To Continue." Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls Page 4 © Yanmar 2008... - Page 7 The i5601E is an extremely versatile display. The four-left keys can be reconfigured to allow the user to display whatever screens he or she desires. For additional operational details, refer to the Appendix A. Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls © Yanmar 2008 Page 5...
-
Page 8: First Time Control Operation
Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls Page 6 © Yanmar 2008... -
Page 9: Operation
NOTE: Indicator Dimming is only accessible from the active control station. (Green lamp on steady.) Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls © Yanmar 2008 Page 7... -
Page 10: Shift Disconnect (Sd)
Move engine’s lever to Forward Idle or Reverse Idle • Press N (Neutral) button next to engine lever. The yellow N (Neutral) lamp will go out - SRT is disengaged. Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls Page 8 © Yanmar 2008... -
Page 11: Sync Operations
Match control handle positions within 5% of each other. (Red lamp goes off when levers match — power train sync is now disengaged.) Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls © Yanmar 2008 Page 9... -
Page 12: Trolling Mode (Option)
CP67601 trolling switch Trolling Switch 40% Throttle Full Lock-up Note: Split Range Throttle (SRT) is not operational while engaged in Trolling mode. Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls Page 0 © Yanmar 2008... - Page 13 HOT KEY Mode, as a dedicated hot key is not required to view these screens. User can hold Right most key down go into the menu mode and then via this menu access the desired screen. Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls © Yanmar 2008 Page ...
-
Page 14: Engine Alarms
Engine with Power Reduction Action Sync OFF Either Engines operate independently Sync ON Master Slave slowly matches master Sync ON Slave Master normal, slave slows Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls Page 2 © Yanmar 2008... -
Page 15: Diagnostics
The shift/throttle control head will flash to indicate improper operation (see the section on the control head function). There is an i8350 or i8355 Engine Control Unit (ECU) mounted in the engine room. On the ECU module are three LED indicator lights which normally flash to acknowledge proper operation. -
Page 16: I8350/55 Operation
Operation i8350/55 Engine Interface Module The switches inside the i8350/55 allow for starting and stopping the engine. • Turn on the ignition switch at the helm. • To start the engine, turn on Emergency Start Power by pressing in the top of the Emergency Start Power Switch. The buzzer will sound. -
Page 17: Appendix A: I5601E Digital Display Setup
Keys NOTE: Any changes to the setup menus may require reconfiguring the i5601E HOT KEY SETUP. Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls © Yanmar 2008 Page 15... -
Page 18: Display Settings
5. That arrow allows the user to select various data inputs in the various sections of the screen. Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls Page 6 © Yanmar 2008... -
Page 19: User Settings And Factory Settings
The i5601E display has the capability of displaying additional information as other devices with NMEA 2000® communication capabilities are added to the vessel. Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls © Yanmar 2008 Page 7... -
Page 20: Quad Screen Parameters
The i5601E display has the capability of displaying additional information as other devices with NMEA 2000® communication capabilities are added to the vessel. Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls Page 8 © Yanmar 2008... -
Page 21: Appendix B I5601E Menu Navigation
Down” Arrow moves menu selection down “Up” Arrow moves menu selection up “Right” Arrow acts on current menu item “Back” Moves back to previous menu Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls © Yanmar 2008 Page 19... -
Page 22: Appendix C: Default Settings
Appendix C For single engine configuration, the engine interface part number is i8350 (no trolling) or i8355 (with trolling). The settings are the same as the dual engine configuration below. Without trolling Engine Interface part number i8350P i8350S Idle RPM... -
Page 23: Appendix D: Fuses
There is a fuse on the back of both the lower station and upper Station Ignition Switch Panels. It is a 5 amp fuse, designation AGC 5A. There are five circuit breakers inside the i8350/55 Engine Interface. See image on page 14 for details. - Page 24 Y0096 OvER HEAT PROTECTION Y0098 vOLTAGE SUPPLY SENSOR Y0099 FAULT IN TPU note: for additional information on fault Codes, see Engine Manual Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls Page 22 © Yanmar 2008...
-
Page 25: Appendix F: Station Select Protection
Warning: Until the green light is on solid, the original active station retains controls of the boat. Electronic Control System: Operation Manual for SY Series Engines with GEN III Controls © Yanmar 2008 Page 23... -
Page 26: Appendix G Network Status
“Back” – Moves back to previous menu Network Nodes Display The Network Units Display shows Yanmar and Teleflex units that have claimed an address on the bus. From the information in the claimed message name (Device Class, Function, and Instance Fields) the type of Model number of the unit will be determined. - Page 27 Brugplein 11, 1332 BS Almere-De Vaart, The Netherlands Phone: +1 770-877-9894 Phone: +31 36-5493200 Fax: +1 770-877-7565 Fax: +31 36-5493209 Yanmar Asia (Singapore) Corporation Pte Ltd. Yanmar Co., Ltd 4 Tuas Lane. Singapore 638613 Head Office Phone: +65 6861-3855 1-32, Chayamachi, Kita-Ku, Osaka 530-8311, Japan Fax: +65 6862-5195 Dealer Network: www.yanmarmarine.com...
Need help?
Do you have a question about the i8350 and is the answer not in the manual?
Questions and answers