ACM DMDPW Operation Manual

□ □ □ □ Operation Panel
9 9 9 9
A
V
9 9 9 9
B
A
9 9 9 9
C
W
→
□ □ □ □ Keys
Key Function
S SET
↑
Change number
→
Change position
〝 〝 〝 〝 S〞 〞 〞 〞 + 〝 〝 〝 〝 → → → → 〞 〞 〞 〞 Reset the value
□ □ □ □ Parameter Setting
〝 〞
Press S to enter function selection (01~09).
〝↑〞
Press to change number. Press
Function
Press↑ and → to set.
Voltage ratio
01
setting Press 〝S〞
Press↑ and → to set.
Ampere ratio
02
setting Press 〝S〞
Press↑to choose ratio 1 or 1000
03 Watt unit ratio
Press 〝S〞
Press↑ and → to set.
Decimal point
04 Change decimal point
setting
〝S〞
Press
05 XXXXXXXX Press 〝S〞
06 XXXXXXXX Press 〝S〞
Press↑to choose Baud Rate
Baud rate
and
(9600-19200-38400-2400-4800)
07
Address Press SET to set Address 1~255.
Press 〝S〞
〝S〞
08 XXXXXXXX Press
Press 〝S〞
09 Save
Key in99 and press
**All parameters are preset by our **All parameters are preset by our factory for you. Please refer to the factory for you. Please refer to the instructions
**All parameters are preset by **All parameters are preset by our our factory for you. Please refer to the factory for you. Please refer to the
S
S e t
↑
C h a n g e n u m b e r
C h a n g e p o sitio n
W H A u to p a g e -tu rn in g
1 0 D ig its d is p la y
O p e ra tio n k e y
3 9 9 9
D is p la y
9 9 9 9 9 9 W H
A la rm s ta te
R e m o v e th e p a n e l lid to se t
Instruction
Enter setting mode.
Set and change number
Change position
Press〝 〝 〝 〝 S〞 〞 〞 〞 and〝 〝 〝 〝 → → → → 〞 〞 〞 〞 to reset the value (WH).
〝→〞
to change position.
Operation Instruction
Ex: Input range DC 0~50 V.
to enter 02. Set 01 as 5000
Ex: Input range DC 0~20A
to enter 03. Set 02 as 2000
Ratio: W =1 ,KW=1000
to enter 04 Set as KW when over 9999 W
Hundreds =V decimal point.
Tens = A decimal point.
Units= W/WH decimal point.
0 0 0 0
Number means how many
to enter 05
digits after decimal point.
to enter 06 No need to set.
to enter 07 No need to set.
Max. Baud rate: 38400
Address:1-255
to enter 08
to enter 09 No need to set.
to enter 89.
Any setting needs to be saved
〝S〞 to save. by keying in 99.
instructions if you need to do any alterations. if you need to do any alterations.
instructions instructions if you need to do any alterations. if you need to do any alterations.
□ □ □ □ Alarm Hi-Lo setting.
Press〝 〝 〝 〝 S〞 〞 〞 〞 to enter〝 〝 〝 〝 00 〞 〞 〞 〞 .Press〝 〝 〝 〝 → → → → 〞 〞 〞 〞 to enter〝 〝 〝 〝 51〞 〞 〞 〞 to set.
Function
51 S1 value setting 0～9999
S1 deadband setting 0～9999
52
53 S1 delay time 0～99 secs
54 S2 value setting 0～9999
S2 deadband setting 0～9999
55
56 S2 delay time 0～99 secs
57 S1；S2 HI-LO setting
Start Delay Time 0～99 secs
58
59 SAVE
The S3 S4 alarm setting procedure is the same as explained above.
Press〝S〞to enter〝00 〞.Press〝↑〞to enter 61-62-63-64-65-66-67 setting selection.
□ □ □ □ Example:
1. Input: Voltage DC 50V Current 20A W=50*20= 1000 W
Set 01(Voltage ratio) as 5000
02(Current ratio) as 2000
03(Watt ratio ) as 1 (unit is W)
04(Decimal point) as 0 2 2 0
2. Input: Voltage DC 600V Current 1000A/50mv W=600V*1000A=600.0KW
Set 01(Voltage ratio) as 6000
02(Current ratio) as 1000
03(Watt ratio ) as 6000 (unit is KW)
04(Decimal point) as 0 1 0 1
Note
:
*All parameters were preset by our factory according to your order specifications.
*If Watt value is blinking, please check if the V, A, W decimal point setting is correct.
Instruction
Press〝↑〞and〝→〞to set S1 value.
Press〝S〞to enter 52.
Press〝↑〞and〝→〞to set S1 deadband.
Press〝S〞to enter 53.
Press〝↑〞and〝→〞to set S1 delay time
Press〝S〞to enter 54.
Press〝↑〞and〝→〞to set S2 value.
Press〝S〞to enter 55
Press〝↑〞and〝→〞to set S2 deadband.
Press〝S〞to enter 56
Press〝↑〞and〝→〞to set S2 delay time.
Press〝S〞to enter 57
Press〝↑〞and〝→〞to set the HI-LO function.
(1=Hi. 0=Lo) Hi-Hi. Hi-Lo. Lo-Hi. Lo-Lo.(selectable).
Press〝S〞to enter 58
Press〝↑〞and〝→〞to set the number as 99.
Set the delaytime from 0~99.Alarm has no action within the
set time. Press〝S 〞to enter 59.
Press〝S〞to enter 89.
Press〝↑〞and〝→〞to key in 99.
Press〝S〞to save.
V= 50.00 A= 20.00 W= 1000
V=600.0 A=1000 W=600.0KW