Summary of Contents for Longrun 100LP
- Page 1 INVERTER AIR PLASMA CUTTING MACHINE 100LP, 130LP, 150LP OPERATION MANUAL DO NOT INSTALL, OPERATE OR MAINTAIN THIS MACHINE WITHOUT READING THIS MANUAL AND PLEASE ALWAYS THINK BEFORE YOU ACT. www.worldwel.com...
- Page 2 - Non contact arc starting by pilot circuit - No need keeping to push torch switch during cutting by turning AUTO switch On which is on front panel of power source ITEM UNIT 100LP 130LP 150LP 220, 380, 440 Input Voltage...
- Page 3 General Safe Practices ■ Wear approved safety glasses with side shields under your welding helmet or face shield and at all times in the work area. ■ When working above floor level, use a safety belt to protect yourself from a fall should you get a shock.
- Page 4 Cutting sparks can cause fire or explosion. ■ Remove fire hazards from the welding area. If this is not possible, cover them to prevent the welding sparks from starting a fire. Remember that welding sparks and hot materials from welding can easily go through small cracks and opening to adjacent areas.
- Page 5 ■ INSTALLATION ● The welding machine shall be installed at a place ; ․ free from the inflammables ․ less humidity, dirt and dust ․ protecting from influence of direct sunlight, wind and rain ․ not generated oil vapor and corrosive gas ․...
- Page 6 220V 380V 440V ● Output Connection (Front of the machine) ․ Connect the work cable (which is connected to the work clamp) to the "+ METAL" terminal. ․ To connect the torch, - Connect a electrode cable to the "- TORCH" terminal - Connect a torch switch connector to the torch switch receptacle - Connect a pilot wire to the pilot receptacle.
- Page 7 When it is turn on, the cooling fan and all of electrical circuit Power Switch inside the machine will be operated. Control Fuse (5A) It will be broken by any electrical problems Current Adjust Volume Adjust the current It indicates that the machine is on and input voltage is within Power Lamp acceptable range.
- Page 8 ■ START UP Turn On the main power supplied to machine Turn On the power switch of machine and then verify that the power lamp is On and the cooling fan is running Regulate the air pressure to 75PSI using the lever of air regulator when air check switch is ON ...
- Page 11 100LP PARTS LIST PART NAME DESCRIPTION QTY. Magnet GMC-30P2 AC220V 50/60HZ Main PCB WTM06[Ver.01] HF PCB TMD-45A89 Control Transformer PCB VAC-01 MF Condensor 15㎌/800V[LARGE] MF Condensor 10㎌/800V[SMALL] Condensor 2200/400V Toggle Switch DWT-6210 Control Transformer 7642 Control Transformer 5719 Input Terminal...
- Page 14 130LP PARTS LIST PART NAME DESCRIPTION QTY. Magnet GMC-30P2 AC220V 50/60HZ Main PCB WTM06[Ver.01] HF PCB TMD-45A89 Control Transformer PCB VAC-01 MF Condensor 20㎌/1000V[LARGE] MF Condensor 10㎌/800V[SMALL] Condensor 2700/400V Toggle Switch DWT-6210 Control Transformer 7642 Control Transformer 5719 Input Terminal 6M/M 3P-80A NDB3-100J4 80/3LTS Pressure Meta...
- Page 17 150LP PARTS LIST PART NAME DESCRIPTION QTY. Magnet GMC-30P2 AC220V 50/60HZ Main PCB WTM06[Ver.01] HF PCB TMD-45A89 Control Transformer PCB VAC-01 MF Condensor 30㎌/800V[LARGE] MF Condensor 10㎌/800V[SMALL] Condensor 3300/400V Toggle Switch DWT-6210 Control Transformer 7642 Control Transformer 5719 Input Terminal 6M/M 3P-100A NDB3-100J4 80/3LTS Pressure Meta...
- Page 18 Thank you very much for choosing our machine Please record your machine identification information below for future reference. This information can be found on the nameplate of your machine. Product Name INVERTER AIR PLASMA CUTTING MACHINE Model Number Date Manufactured Serial Number Date Purchased Where Purchased...