Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ace Vision Series
Summary of Contents for Ace Vision Series
- Page 1 ACE Vision Series: X3H410TS User Manual Revision 1.0 Revision Date: 12.7.2021...
- Page 2 Please Note: For the most up-to-date version of this manual, please see our website at www.acecomputers.com. Ace Computers reserves the right to make changes to the product described in this manual at any time and without notice. This product, including software and documentation, is the property of Ace Computers and/ or its licensors, and is supplied only under a license.
- Page 3 If you have any questions regarding this manual or computer system, please contact our support team through Ace Computers Support page https://acecomputers.com/support/ .This manual may be periodically updated without notice. Please check the Ace Computers website for possible updates to the manual revision level. ACE095 Page 3 of 17 Rev Date: 12.7.2021...
-
Page 4: Table Of Contents
Table of Contents Table of Contents Chapter 1 - Illustrated System Disassembly Instructions ..............5 Data Storage Devices ......................... 6 Memory ............................. 8 Processor ............................9 Motherboard ........................... 10 Expansion Card/Graphics Card ......................11 Power Supply Module ........................12 Chassis Cover ........................... 13 Batteries ............................ -
Page 5: Chapter 1 - Illustrated System Disassembly Instructions
Chapter 1 - Illustrated System Disassembly Instructions Chapter 8 is intended to provide guidance to recyclers on the presence of materials and components at the product/family level, per Article 15 of the EU WEEE Directive 2012/19/EU. The provided information should also help direct recyclers to proper methods for removing parts and general product disassembly instructions. -
Page 6: Data Storage Devices
1. Data Storage Devices Location: Desktops utilize interchangeable storage. These storage hard drives are located as indicated in the photos below. Some desktops also have SSD storage, this type of storage can be found on the motherboard. It generally lays flat, parallel to the board, rather than at a right angle. - Page 7 Step 3 ACE095 Page 7 of 17 Rev Date: 12.7.2021...
-
Page 8: Memory
Memory Location: Memory modules are found on the motherboard of the desktop, the number of memory modules may vary by unit configuration but are generally found in pairs of 2. Type and number of fastenings: Two (2) latches per memory module. Tools required: None. -
Page 9: Processor
3. Processor Location: The processor is found on the motherboard of the desktop. As shown in the photo below, the processor is located under the heat sink. There can only be one processor on the motherboard for this model. The processor could consist of a push-pin based Intel heatsink. Type and number of fastenings: Push-Pin Tools required: NA Procedure: Intel Processor: Remove the push-pin from the base of the heatsink and lift the... -
Page 10: Motherboard
4. Motherboard Location: The motherboard is generally centrally located within the unit. Standard practice would be to remove all the components, peripherals, and add-ons from the motherboard before removal of the motherboard for processing. Type and number of fastenings: 8 Phillips screws. Tools required: Screwdriver with PH2 bit. -
Page 11: Expansion Card/Graphics Card
5. Expansion Card/Graphics Card Location: Certain configurations of desktops may include expansion and/or graphics cards. These will be found in the lower right-hand corner of the motherboard. They’re electrically connected to the motherboard and physically connected to the case. Type and number of fastenings: Two (2) Phillips screws. Tools required: Screwdriver with PH2 bit. -
Page 12: Power Supply Module
6. Power Supply Module Location: The power supply module is located in the back left hand corner. Type and number of fastenings: Three (3) Phillips Screws per module. Tools required: Screw Driver. Procedure: Unplug the power cord from the power supply. To remove the power supply, remove the three exterior Phillips screws. -
Page 13: Chassis Cover
7. Chassis Cover Location: The chassis cover is located on the top and is held in place with two Phillips screws. Type and number of fastenings: Two (2) screws. Tools required: Phillips screwdriver. Procedure: Remove two screws and gently pull the handle backwards. Selective Treatment/Special Handling Per Annex VII, Directive 2012/19/EU: None ACE095 Page 13 of 17... -
Page 14: Batteries
8. Batteries Location: The battery is located on the motherboard, see illustration below. Type and number of fastenings: One (1) latch. Tools required: None. Procedure: Push aside the small clamp that covers the edge of the battery. When the battery is released, lift it out of the holder. -
Page 15: Fans
9. Fans Location: The chassis fan is located underneath the hard drive/optical drive mounting bracket, in the top right-hand corner, as noted in the photo below. Type and number of fastenings: Four (4) Phillips Screws. Tools required: Phillips Screwdriver. Procedure: Release hard drive/optical drive mounting bracket and move into the upright position. -
Page 16: External Power Cable
External Power Cable Location: The inlet to the power cable is located on the power supply. If connected, the power supply would be located there. Type and number of fastenings: None, direct pressure connection method. Tools required: None. Procedure: Disconnect the external power cable from the main desktop assembly with a firm pull at the base of the connection method. -
Page 17: Chapter 2 - Product Take-Back, End-Of-Life Processing, And E-Waste Program
Member will reach out to further assist with your technical questions. If it is determined that the best course of action is an inhouse repair at Ace Computers, the service technician will help facilitate the process of returning the system for repair.
Need help?
Do you have a question about the Vision Series and is the answer not in the manual?
Questions and answers