Wickes AVI WHITE LED KIT Instruction Manual

CONTENTS
HEALTH & SAFETY GUIDELINES
GENERAL PRODUCT INFORMATION
CONTENTS
TOOLS FOR THE JOB
INSTALLATION INSTRUCTIONS
FITTING/REPLACING THE BULB
CARE & CLEANING
CUSTOMER SUPPORT
HEALTH & SAFETY GUIDELINES
CAUTION
Read all safety instructions carefully. Failure to comply
with the following safety instructions may cause
electric shock, fire and/or serious injury.
ELECTRICAL SAFETY
For your safety, this product must be installed in
accordance with local Building Regulations. If in
any doubt, or where required by the law, consult a
competent person who is registered with an electrical
self-certification scheme. Further information is
available online or from your Local Authority.
Before commencing any work ensure the supply is
switched off at the mains. Either by switching off
main switch at the consumer unit or by removing the
appropriate fuse.
As from April 2004 twin and earth wiring colours
changed;
EARTH Green/yellow sleeving
LIVE Brown replaces red
NEUTRAL Blue replaces black
2
3
3
3
3
4
4
4
To prevent a fire hazard always use the cable of correct
rating, size and type for application.
Ensure all terminal screws are tight and all wires are
neatly routed and not unduly stretched or pinched.
All earth connections must be made and continuity
maintained.
Where any earth conductor is a bare wire, it must be
sleeved with green/yellow sleeving.
If connecting to a switch, the switched live conductor
must be appropriately identified.
If drilling new holes, be sure to locate cables before
beginning work, to avoid electric shock and damage to
existing circuits.
GENERAL SAFETY
When working at heights, make sure you are using the
correct equipment and follow all safety instructions.
Make sure that your workplace is tidy, clear from
debris, well lit and dry.
GENERAL PRODUCT INFORMATION
S15
MAX 60W
INDOOR
LAMP TYPE &
USE ONLY MAX.
WATTAGE
CONTENTS
– 4 x White LED strip lights, each with 1m cable & end cap
– Connection box with 2.3m cable
– In-line LED driver with 3 pin removable plug
– 3 x 1m corner connection cables
- 3 x 0.1m corner connection cables
- Fixing pack
TOOLS FOR THE JOB
– 2mm slotted screwdriver or electrical screwdriver
– Cross head screwdriver
INSTALLATION INSTRUCTIONS
Siting Instructions
III
These units are Safety Extra Low
Voltage and must not be earthed.
1) This product is designed for use under kitchen
cupboards, bookshelves, cabinets etc. Suitable for
indoor use only. Not suitable for bathrooms.
2) Do not attach to surfaces which are damp, freshly
painted or otherwise electrically conductive (e.g.
metallic surfaces).
3) The chosen location should allow for the product to
be securely mounted and safely connected to the mains
supply (240v wall socket). Alternatively, connect the
supplied mains lead to a 3 Amp fused outlet. Remove the
3 -pin plug supplied with the product and wire direct
into the fused outlet. The Brown wire must be connected
to the terminal marked L or coloured red. The Blue wire
must be connected to the terminal marked N or coloured
black.
Using this method means the kit will be controlled via
a wall switch. If in doubt please consult a qualified
electrician.
4) Ensure cables are routed to avoid accidental damage
or hazard.
– Instruction manual (retain for future reference)
PARTS MISSING?
Contact the customer service helpline number and quote
Wickes 218797
Installation
1) Lay out/ measure the positions of the head units as
desired. Ensure cables are routed to avoid accident or
damage occurring. Cables can be taped to mounting
surface after installation.
2) Each head unit is supplied with 1m of cable. The
cable from the driver to connection box is 2.5m long.
The head units can be laid out in many positions using
different combinations of heads and connector cables.
See diagram overleaf for example layouts and choose
one to suit your requirements.
3) Attach heads in position using either the supplied
screws and clips or self adhesive pads.
4) Fix connection box to mounting surface using
supplied adhesive pad. Connect all heads to the
connection box, route loom to desired power source.
(240V mains socket) Again taking care not to create
a trip hazard. Cables can be tidied and secured to
the mounting surface using tape or small clips (not
supplied).
5) Connect loom to driver. Check all connections are
tight.
6) Plug in and test.
7) Your lights are now ready for use.