Walker H10 Operator's Manual

Implement hitch mount

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

H10 & H19 Implement Hitch Mount

Operator's Manual

Assembly, Attaching, Removing, Operation and Maintanence

Please Read and Save These Instructions

For Safety, Read All Assembly and Opeartion Instructions

Prior to Operating Attachment

H10 compatible with Models C, D, T

H19 compatible with Model H

Beginning S/N: 10-4651

Effective Date: 03.29.10

P/N: 6618-1

Table of Contents

Summary of Contents for Walker H10

Page 1 H10 & H19 Implement Hitch Mount Operator’s Manual Assembly, Attaching, Removing, Operation and Maintanence H10 compatible with Models C, D, T H19 compatible with Model H Please Read and Save These Instructions Beginning S/N: 10-4651 Effective Date: 03.29.10 For Safety, Read All Assembly and Opeartion Instructions...
Page 2 Foreword Thank you. . .for purchasing a Walker Implement Hitch Mount. Every effort has been made to provide you with the most reliable machine on the market, and we are sure you will be among our many satisfied customers. If for any reason this product does not perform to your expectations, please contact your local dealer.
Page 3: Table Of Contents
Most accidents associated with the operation or maintenance of a Walker product are caused by disregarding basic safety precautions or specific warnings. Such accidents, in most cases, can be prevented by being aware of the...
Page 4: Safety Instructions
Become thoroughly familiar with all controls and how to stop the machine and disengage the controls quickly. Replacement Operator’s Manuals are available on www.walkermowers.com or by sending the model and serial number to: Walker manufacturing Company 5925 E. Harmony Road Fort Collins, CO. 80528 never allow children to operate or give rides on the machine.
Page 5 10. never attempt to make any adjustments while the engine is running, except where specifically instructed to do so. 11. Handle gasoline or diesel fuel with care. Gasoline is highly flammable and its vapors are explosive: a. Use an approved fuel container. b.
Page 6 8. Avoid sudden starts or stops. Before backing the machine up, look to the rear to be sure no one is behind the machine. Watch carefully for traffic when crossing or working near roadways. 9. Disengage the PTO clutch when transporting the machine. 10.
Page 7 Perform only maintenance instructions described in this manual. Unauthorized maintenance operations or machine modifications may result in unsafe operating conditions. 5. If the engine must be running to perform a maintenance adjustment, keep hands, feet and clothing away from moving parts. Do not wear jewelry or loose clothing. Always use proper engine service manuals when working on the engine.
Page 8: Decals
Speed Control (fSC) lever Part number: 6632 RAISE LOWER 6632 Adjustment Decal: 3/4” Bolt - H10 onlY IMPORTANT location: frame of H10 Implement Hitch WHEN INSTALLING IMPLEMENT ADAPTOR Part number: 6618 ADJUST BOLT HEAD TO CONTACT CROSS MEMBER...
Page 9: Assembly
Control (FSC) lever for convenient operator use, and controls a linear actuator on the implement hitch. Walker implement hitches are shipped partially assembled. After uncrating the implement hitch, initial setup is required. H10 Implement Hitch Wiring: models C, D, and T 1.
Page 10 2. Attach the toggle switch to the mounting bracket, placing the switch terminals toward the front of the mower. 3. If a hole is not present in the location shown in figure 1.2, drill a 3/16 in. hole in the right front body to attach the cable clamp.
Page 11 H19 Implement Hitch Wiring: model H 1. Attach the toggle switch mounting bracket to the FSC lever using two (2) 10-24 x 1/2” bolts and Keps nuts (figure 1.4). 2. Attach the toggle switch to the mounting bracket, placing the switch terminals toward the back of the mower (figure 1.4).
Page 12 Implement Hitch Wiring Diagram Actuator Switch 20 AMP CIRCUIT BREAKER Green Purple (Chassis GND) Model H Tractors Wire Harness Model C, D, and T Assembly Tractors 30 AMP CIRCUIT BREAKER Actuator...
Page 13: Attaching Implement Hitch
Attaching Implement Hitch Attaching H10 Implement Hitch to models C, D, or T 1. Remove the mower deck from the tractor, if necessary. Refer to the appropriate Tractor Operator’s Manual. 2. Lightly grease both support arms on the tractor. Refer to figure 2.1 for location of the support arms.
Page 14 6. After the hitch is installed, complete the wiring by connecting the wiring harness to the actuator motor of the implement hitch. 7. Raise and lower the hitch a few times to check the operation and make sure it moves smoothly.
Page 15 Attaching H19 Implement Hitch to model H 1. Remove the mower deck from the tractor, if necessary. Refer to the appropriate Tractor Operator’s Manual. 2. Lightly grease both support arms on the tractor. Refer to figure 2.2 for location of the support arms.
Page 16: Operation
All implements must be locked in place on the implement hitch before beginning any operation. H10: locking/Removing Implements • locking: Rotate the hitch lock lever fully forward to the loCKeD position, and secure the hitch latch with the linch pin.
Page 17 H19: locking/Removing Implements • locking: Rotate the hitch lock lever fully backward to the loCKeD position • Removing: Move the hitch lock lever forward to the UnloCKeD position. H19: float function Adjustment • non-floating: Insert the clevis pin (figure 3.2) through the rear actuator mount and secure with the bowtie cotter pin.
Page 18: Removing Implement Hitch
Removing Implement Hitch 1. Park the tractor on a level surface and lower the implement hitch. Warning Do noT attempt to remove the implement hitch with the tractor engine running. Stop the engine and remove the ignition key. Wait for all movement to stop before getting off the seat.
Page 19: Maintenance
Maintenance H19 Hitch lock Tension Adjustment After installing an implement onto the hitch, the hitch lock clevis will need to be adjusted according to the following procedure: 1. Adjust the H19 hitch lock clevis to properly secure the implement. To adjust the tension on the tongue latch, remove the bowtie clip and the clevis pin as shown in figure 3.1, and twist the male clevis clockwise to tighten, or counter-clockwise to loosen, as needed.
Page 20 Tractor Lubrication Points are not shown here. For Tractor Lubrication Points, refer to the appropriate Tractor oPeRAToR’S mAnUAl or IllUSTRATeD PARTS mAnUAl. H10 lubrication Points location lubrication Type no. Places PTO Shield Hinge...
Page 21 H19 lubrication Points location lubrication Type no. Places Mounting Tube Sockets Grease Hitch Locking Arm Pivot Shaft Mounting Tube Sockets Pivot Shaft Hitch Locking Arm PTO shield has been removed for illustration purposes ONLY...
Page 22: Parts List/Diagram
Mounting Frame Assembly, Hitch (Includes Item # 17-18) * NS Non-Sellable 6618 Decal, Hitch Mount Adjust 6619 Mount Adjustment Bolt 8735-10 Rubber Mat (5 x 6) 6626 Pivot Shaft Beginning S/N 10-4651 Effective Date 03.29.10 Use only genuine Walker® replacement parts...
Page 23 ImPlemenT HITCH ASSemBlY (H10) F002 F026 F026 F026 F026 F002 F036 F026 F026 F068 F002 F027 F005 HARNESS RUNS ON HARNESS RUNS ON OUTSIDE OF BODY OUTSIDE OF BODY F002 F068 F213...
Page 24 (Includes Item #13) 4407-4 Bow Tie Cotter Pin 6619-16 Clevis, Male 6619-17 Clevis, Female 5850-3 Handle Grip, Foam (3-1/4) 6619-29 Locking Arm (Includes Item # 33) 1 6621-11 Linear Actuator Beginning S/N 15-5951 Effective Date 10.01.15 Use only genuine Walker® replacement parts.
Page 25 ImPlemenT HITCH ASSemBlY (H19) F002 F026 F004 F246 F004 F004 F029 F009 F002 F246 F029 F034 F004 F014 F034 F034 F026 F009 F009 F014 F009 F009 F034 F034 F111 F134 F009 F034 F111 F068 F134 F209 F068 F209 INSERT CLEVIS PIN 6621-9 TO MAKE ATTACHMENT NON FLOATING F049...
Page 26 oPeRAToR’S noTeS...
Page 27: Warranty
(90) days. At Walker’s request, customer will make the defective part available for inspection by Walker and/or return the defective part to Walker, transportation charges prepaid.
Page 28 WAlKeR mfg. Co. 5925 HARmonY RoAD, foRT CollInS, Co. 80528 - (970)221-5614 FORM NO. 111315 PRInTeD In USA...

This manual is also suitable for:

H19