Related Manuals for MSH equipment BT UV-02-L
Summary of Contents for MSH equipment BT UV-02-L
- Page 1 Taal: engels Handleiding B TEC UV droger 2 en 4 lamps BT UV-02-L/BT UV-04-L MSH equipment Appelmarkt 7 1681 PE Zwaagdijk-Oost Tel: 0228-561100 Fax: 0228-561112 Mail: info@msh-equipment.nl Website: www.msh-equipment.nl...
- Page 2 equipment and facility engineering UV-Emitter UV-02 L / UV-04 L User Manual for Short Wave Ultra Violet Paint Curing Equipment B -TEC GmbH • Zunftweg 6-8 • D-31303 Burgdorf / Ehlershausen • Telephone : ++49(0)5085-97100-0 Fax : ++49(0)5085-97100-30 • Email : info@btecsystems.de • www.btecsystems.de...
- Page 3 equipment and facility engineering Declaration of Conformity According to DIN EN 45014 Manufacturer: B-TEC GmbH Zunftweg 6-8 D-31303 Burgdorf / Ehlershausen Herewith, we declare that the machines and marketed models described in the following conform in conception and in design to the relevant fundamental safety and health requirements of the applicable EU directives.
-
Page 4: Table Of Contents
equipment and facility engineering Table of Contents 1. Important Information ..........................1 2. Safety Regulations and Maintenance Advices ..................2 2.1 Work Area ............................2 2.2 Use ..............................2 2.3 Electroshock Hazards ......................... 3 2.4 Fire and Explosion Hazards ......................... 4 2.5 UV Radiation Hazards ......................... -
Page 5: Important Information
equipment and facility engineering 1. Important Information We thank you for your trust you gave to us by buying the UV-emitter. At the rating plate at your device you will find the exact name and serial-number of your infrared emitter for an uncomplicated service and shipment of spare parts. -
Page 6: Safety Regulations And Maintenance Advices
equipment and facility engineering 2. Safety Regulations and Maintenance Advices The B-TEC GmbH machines are operationally safe and are constructed according to the state of the art. Due to the nature of the processes there are processes and parts that cannot be protected without impairing operability and functionality. -
Page 7: Electroshock Hazards
equipment and facility engineering the machine, in order to avoid electric shocks. Any unconscious start of this machine should be avoided. When you leave the work area or the work is done, make sure the power is shut down and the wire is unplugged. -
Page 8: Fire And Explosion Hazards
equipment and facility engineering 2.4 Fire and Explosion Hazards Fire can cause serious injuries, death and damage of properties! Please read, understand and follow the safety instructions below, in order to reduce the risk of injuries, death and damage of properties due to fire. In addition, ensure that every operator of the device follows the safety instructions. -
Page 9: Maintenance And Care
equipment and facility engineering 2.6 Maintenance and Care Regular cleaning of tubes and reflector panel should be done by using a piece of soft cloth or cotton with alcohol (Note: cleaning must be conducted after the machine is disconnected with the power and cooled down). -
Page 10: Technical Description Of The Device
equipment and facility engineering 3. Technical Description of the Device The short-wave UV paint dryer is specialised in curing UV automotive paint, which is featured with high penetrability, short baking time at low process temperatures, long service life, high cost efficiency, convenient and flexible use without site limit. -
Page 11: Wiring Diagram
equipment and facility engineering 3.2 Wiring Diagram UV-02 L UV-04 - Technical changes and errors reserved. All pictures similar - UV-02 L / UV-04 L Page 7... -
Page 12: Spare Parts List
equipment and facility engineering 3.3 Spare Parts List UV-02 L UV-04 L UV-02 L / UV-04 L Beschreibung Art-No.: Beschreibung Art-No.: Front Wheels without Break Control Panel Rear Wheels with Break Protective Glass Pedestal Lamp cassette Column Cable Hook Handle U-shaoed Support Adjustable Handle Cross Arm... -
Page 13: Installation
equipment and facility engineering 4. Installation Caution! When installing, do not press the handle oft he pneumatic cylinder, otherwise it may cause injury due to the rapid lifting of the cross arm! UV-02 L The angle of the emitter cassette can be adjusted: Baking Area: - Technical changes and errors reserved. - Page 14 equipment and facility engineering UV-04 L The angle of the emitter cassette can be adjusted: UV-02 L UV-04 L - Technical changes and errors reserved. All pictures similar - UV-02 L / UV-04 L Page 10...
-
Page 15: Operation
equipment and facility engineering 5. Operation (1) Time Window (2) Memory Keys (3) Time Adjust Key (4) Key for Emitter-Tube (5) Key for Emitter-Tube (6) Beep Sound Switch (8) Pause/off key (press once to pause and twice to stop). (9) Start Key (10) Power Key UV-02 L UV-04 L... - Page 16 equipment and facility engineering 6. Set curing time. There are 3 ways in order to set the curing time: a. Use default time. b. Adjust curing time by using the buttons c. Use a time of the memory (2). 7. Select emitter cassettes (4, 5). All emitters can be operated separately. 8.
-
Page 17: Replacement Of Emitter Lamp Tube
equipment and facility engineering 6. Replacement of Emitter Lamp Tube Interrupt the power supply, before replacing the emitter tube! 1. Remove the side panel ①. 2. Release the radiating panel ②. 3. Loosen the two leads in the lamp and remove them. 4.
Need help?
Do you have a question about the BT UV-02-L and is the answer not in the manual?
Questions and answers