SDC 400W1-433 Installation Instructions

Advertisement

SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
SECURITY DOOR CONTROLS ■ WWW.SDCSECURITY.COM
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: service@sdcsecurity.com ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: service@sdcsecurity.com ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011
[t] 800.413.8783 ■ 805.494.0622 ■ E-mail: service@sdcsecurity.com ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011

Programming -

NOTE: The 400W1-433 Transmitter is only compatible with the 400RC433 Receiver.
1) Attach battery to the 400W1-433 transmitter.
2) Push P1 on the Receiver 1 channel 433 until you hear a beep, then touch the black flagged wires together
and hold until the receiver beeps again. The 400W1-433 will then be programmed into the receiver.

Troubleshooting -

Problem
A) The receiver does not receive the transmitter signal
and the transmitter LED will not light up.
B) Operation is very weak or sporadic
3) Attach quick connects to switch. Twist wires from the switch and transmitter together and insert into the gel
connector and crimp.

Technical Specifications

Operating Frequency
Battery
Operating Temperature
Type – 433TSPWIK
FCC IS: SU433TSP4K
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference, and
2) This device must accept interference received, including interference that may cause undesired operation.
P:\INST INSTRUCTIONS\ADA CONTROLS\INST-400W1-433
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
400W1-433 Transmitter
433 Frequency
-
433 MHz
-
9 Volt DC
-
-20 C -100 F
REV A
Solution
Change the battery
Change the battery or check the wiring on the
transmitter or receiver to make sure wires are
secure and not pinched.
11-21
Page 1
4OOWI-433
9 VOLT
FREQUENCY:
433.22 MHz
BATTERY
SUPPLY : 9V DC
WIKK WIRELESS
Any suggestions or comments to this instruction or
product are welcome. Please contact us through
our website or email engineer@sdcsecurity.com
ANTENNA

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 400W1-433 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for SDC 400W1-433

  • Page 1 1) Attach battery to the 400W1-433 transmitter. 2) Push P1 on the Receiver 1 channel 433 until you hear a beep, then touch the black flagged wires together and hold until the receiver beeps again. The 400W1-433 will then be programmed into the receiver. ANTENNA...
  • Page 2 [t] 800.413.8783 ■ 805.494.0622 ■ E-mail: service@sdcsecurity.com ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011 [t] 800.413.8783 ■ 805.494.0622 ■ E-mail: service@sdcsecurity.com ■ 801 Avenida Acaso, Camarillo, CA 93012 ■ PO Box 3670, Camarillo, CA 93011 P:\INST INSTRUCTIONS\ADA CONTROLS\INST-400W1-433 REV A...

Table of Contents