Subscribe to Our Youtube Channel
Related Manuals for Pro-Aqua PRO+RO Series
Summary of Contents for Pro-Aqua PRO+RO Series
- Page 1 Professional Water Filtration Systems www.proaquawater.com.com PRO+RO SERIES USER & SERVICE MANUAL...
-
Page 2: Table Of Contents
TABLE OF CONTENT Introduction / System Specifications ....................3 1. Principles of Reverse Osmosis ....................4 - Reverse Osmosis Process ......................4 - Semipermeable membrane ......................4 - Factors affecting membrane service life ................4 - Reverse Osmosis System Terms and Definitions ..............4 - Feed Water requirements ......................5 2. -
Page 3: Introduction / System Specifications
77 °F, and SDI < 5. Use a suitable pretreatment capable of removing all membrane damaging substances. PRO+AQUA PRO+RO Series Reverse Osmosis systems If you purchased any of these systems with some variation or special design and it is not described have been designed and tested to provide high quality in this manual, please contact us indicating the corresponding serial number. -
Page 4: Principles Of Reverse Osmosis
PRINCIPLES OF REVERSE OSMOSIS Principles of Reverse Osmosis Technology 2. Hydrolysis: It is a chemical reaction of water that affects the membrane. This happens when the water temperature is very high and the pH is below 2.5 or above 7. To avoid this, keep the How the Reverse Osmosis process works? pH between 5 and 6. -
Page 5: Feed Water Requirements
PRINCIPLES OF RO & IDENTIFYING SYSTEM COMPONENTS Feed Water Requirements SYSTEM COMPONENTS TYPICAL EXPECTED ION RETENTION 1. PREFILTER PRESSURE GAUGE: Glycerin filled pressure gauge IN A TFC MEMBRANE TYPE: (0-100psi). Standard on all units and is located on the front of the panel. - Page 6 IDENTIFYING SYSTEM COMPONENTS Turning the valve knob will control the ratio of water discharged / water produced. CAUTION! Never use the pump without water. - Turning clockwise will increase pressure inside of the module and reduce the amount of waste water. - turning counterclockwise pressure will decrease within the module 12.
-
Page 7: Pre Installation References
PRE INSTALLATION REFERENCES & REVERSE OSMOSIS SYSTEM INSTALLATION PRE INSTALLATION REFERENCES the housing. Recommendations how to insert membranes into the SS housing: Inlet Feed Water - enters through the pre-filter housing. The - To insert the membrane in the SS housing it is recommended housing connection is ¾... -
Page 8: Controller Programming
CONTROLLER PROGRAMMING - At initial start-up, the PRO+RO system counts in seconds until it reaches minutes and later to hours as in the example below. PROGRAMMING THE CONTROLLER TIMER TIMER TIMER 00:59 01:00 01:10 (59 seconds) (1 minute) (1 hour : 10 seconds) NAVIGATION AND PROGRAMMING MENU: - When the system reaches 1 hour of continuous operation the system screen counts in hours and minutes as in the... -
Page 9: Information Displayed On Screen
CONTROLLER PROGRAMMING INFORMATION DISPLAYED ON SCREEN: SETTING PARAMETERS: Timer - Indicates the time the system P1 - Time Setting adjustment for the duration of the membrane TIMER has been working and starts measuring fast flush; 15 sec, 30 sec, 45 sec, 60 sec. 1:01 a range of time (minutes: seconds), after an hour of operation this changes its time... -
Page 10: Cable Connection Identification
CONTROLLER PROGRAMMING CABLE CONNECTION IDENTIFICATION: TDS SENSOR CALIBRATION (CONTROLLER): - The controller has a basic TDS sensor that gives you a reading Violet: Low level Switch in the raw water tank (SW1) (*) of the quality of your product water that fills your tank. Blue: Shut-Off Switch for the pre-treatment (SW2) (*) - If you want to verify the calibration of the sensor,... -
Page 11: Start-Up
START-UP START-UP 10. The reverse osmosis unit is now in operation. Check for leaks. PPM product water will take approximately 60 minutes to reach the optimum final quality since the membranes 1. Make sure that everything related to the pre-treatment must be flushed from preservants. -
Page 12: Troubleshooting Guides
TROUBLESHOOTING GUIDE TROUBLESHOOTING GUIDE Symptom Possible Cause Solution A) Power switch is off. A) Place in AUTO position. B1) Check power outlet and make sure system is plugged in. B) No power. B2) Check 2AMP fuse on back of controller. C1) Verify that the feed valve is fully open. - Page 13 TROUBLESHOOTING GUIDE Symptom Possible Cause Solution A) saturated or dirty membrane. A) Check, clean, replace if necessary. B) Check your feed water temperature, check your correction 4) No product or too B) The water temperature is very low. factor for the temperature and make sure that the flow is at an acceptable level.
-
Page 14: Reverse Osmosis Pre-Treatment
REVERSE OSMOSIS PRE-TREATMENT PRE-TREATMENT REQUIRED 1. Sediment filter: These filters are designed to remove FOR REVERSE OSMOSIS SYSTEMS. sediment present in the raw water and are important to prevent dirt from reaching the membrane and fouling it quickly. Various filtering materials such as: multimedia, silica This flow chart shows the typical pre-treatment and post- treatment equipment to complete the purification process. -
Page 15: Warranty
PRO+AQUA will provide replacement parts to the original equipment purchaser in possession of a PRO+RO Series RO System that fails within (1) one years after the date of purchase, provided that it is at all times operated in accordance with specifications and not subject to freezing, sunlight or installed outdoors. - Page 16 Professional Water Filtration Systems www.proaquawater.com.com © Copyright PRO+AQUA. All Rights Reserved.
Need help?
Do you have a question about the PRO+RO Series and is the answer not in the manual?
Questions and answers