Advertisement
Quick Links
COSEC ARGO
COSEC ARGO CAE200/ CAM200/ CAI200
COSEC ARGO FOE212/ FOM212/ FOI212
Contents
Assigning IP Address and Other Network Settings
Technical Specification
Assigning IP Address
Please read this guide first for correct installation and retain it
for future reference. The information in this guide has been
authenticated at the time of publication. However, Matrix
Comsec reserves the right to make changes in product design
and specifications without prior notice.
3
7
7
8
9
11
17
23
24
25
2
Advertisement
Summary of Contents for Matric COSEC ARGO CAE200
-
Page 1: Table Of Contents
COSEC ARGO Contents Know your COSEC ARGO What your Package Contains COSEC ARGO CAE200/ CAM200/ CAI200 Assigning IP Address and Other Network Settings Preparation for Installation Technical Specification Installation Instruction - Wall Mounting Installation Instruction - Flush Mounting Connecting the Cables... -
Page 2: Know Your Cosec Argo
Rear View (Common for both Series) Know your COSEC ARGO Figure 2 The COSEC ARGO is available in two series with three different variants in each series as follows: 1) COSEC ARGO with variants FOE212, FOM212 and FOI212. 2) COSEC ARGO with variants CAE200, CAM200 and CAI200. - Page 3 Pre-Installation Safety Instruction 5. Do not install the device in outdoor areas which may be exposed to rain, cold and dust. You can do indoor installation or on the turnstile 1. Do not install the device in extremely hot temperature or under direct under the roof as shown in Figure 5.
-
Page 4: What Your Package Contains
What your Package Contains For Concealed wiring in Wall Mounting/Flush Mounting, first draw out the sufficient length of the cables from the hole of the mounting plate. 1) COSEC ARGO Unit 6) Power Adapter 12VDC,2A 2) Flush Mounting Plate 7) Power Supply Cable (with DC Jack) For Non-concealed wiring in Wall Mounting;... -
Page 5: Installation Instruction: Wall Mounting
Installation Instruction: Wall Mounting Step 2: Drill the screw holes along the traced markings. Fix Wall Mounting plate with the supplied screws. Tighten the screws with screw driver. Step 1: Place the Wall Mounting plate and trace screw holes 1 and 2 on the wall where the device is to be installed. - Page 6 Step 3: Connect the cables of the ARGO unit and lead all the cables • Keep all the cables parallel to the side of the COSEC ARGO through the duct of the Wall Mounting plate into the electrical box body in such a way that it should not cover the back portion recessed in the wall i.e.
- Page 7 Step 4: Align COSEC ARGO on the mounting plate and hook it Step 5: Insert the mounting screw into the mounting screw hole into the mounting slot. Press the bottom side inwards to lock it in at the bottom of the device. Tighten the screw to complete the place.
-
Page 8: Installation Instruction: Flush Mounting
Installation Instruction: Flush Mounting Step 2: Place and fix the Flush Mounting plate with the supplied screws. Tighten the screws with screw driver. Step 1: Place the Flush Mounting Template on the desired installation surface. Mark the area along the dotted line and trace the four screw •... - Page 9 Step 3: Connect the cables of the ARGO unit and lead all the Keep all the cables parallel to the side of the COSEC ARGO • cables through the Flush Mounting plate into the electrical box body in such a way that it should not cover the back portion recessed in the wall.
- Page 10 Step 5: Insert the mounting screw into the mounting screw hole Step 4: Align COSEC ARGO with the mounting plate and hook it at the bottom of the device. Tighten the screw to complete the into the mounting slot. Press the bottom side inwards to lock it Flush Mounting.
-
Page 11: Connecting The Cables
Connecting the Cables For Concealed wiring; first draw out sufficient length of the • cables from the hole you have made on the mounting Micro USB surface. connector cable EM Lock Cable Ethernet Cable Connect the Power, External Reader and EM Lock cable •... - Page 12 Assigning IP Address and Other Network Settings Diode Connection for Back EMF Protection Open the Web browser in your computer. • Relay Relay Enter the IP Address of the COSEC ARGO, default: • Pin 1 Pin 2 http://192.168.50.1 in the address bar of the browser and press the Enter key on your computer keyboard.
-
Page 13: Technical Specifications
Technical Specification Technical Specification Event Buffer 5,00,000 Thermal Sensor Operating 0 °C to +50 °C Input Power 12V DC @2A and PoE Temperature Reader Power Max 12V DC @0.250 A Dimensions 186mm x 74mm x 50mm (Wall Mount) Output (H x W x D) 186mm x 74mm x 16mm (Flush Mount) Reader Interface RS 232 and Wiegand... - Page 14 Disposal Of Product After End-Of-Life FCC Compliance This device complies with part15 of the FCC rules. Operation is subject to WEEE Directive 2002/96/EC the following two conditions: 1. This device may not cause harmful interference. The product refered is covered by the waste Electrical and 2.
- Page 15 Copyright All rights reserved. No part of this document may be copied or reproduced in any form or by any means without the prior written consent of Matrix Comsec. Warranty Limited Warranty. Valid only if primary protection is provided, mains supply is within limit and protected, and environment conditions are maintained within product specifications.