3Built RES126VX Quick Start Manual
Hide thumbs
Also See for RES126VX:
- Installation instructions (5 pages) ,
- Installation instructions (3 pages)
Table of Contents
Advertisement
Quick Links
RES126VX
Receiver Programming
These instructions are for programming Receivers to a new Transmitter. Please be sure to read the
entire instructions before programming.
Contents
OPENING THE TRANSMITTER ........................................................................................................................ 2
PROGRAMMING TRANSMITTER TO RECEIVER .............................................................................................. 3
RESET RECEIVER ............................................................................................................................................ 4
OPTIONAL SETTINGS FOR THE RECEIVER ...................................................................................................... 5
OPENING THE TRANSMITTER ........................................................................................................................ 6
PROGRAMMING TRANSMITTER TO RECEIVER .............................................................................................. 7
RESET RECEIVER ............................................................................................................................................ 8
OPTIONAL SETTINGS FOR THE RECEIVER ...................................................................................................... 9
©2020 3Built LLC
Page 1 of 9
10/5/2020
Advertisement
Table of Contents
Related Manuals for 3Built RES126VX
Summary of Contents for 3Built RES126VX
-
Page 1: Table Of Contents
OPTIONAL SETTINGS FOR THE RECEIVER ...................... 5 Long Range Transmitter OPENING THE TRANSMITTER ........................6 PROGRAMMING TRANSMITTER TO RECEIVER ....................7 RESET RECEIVER ............................8 OPTIONAL SETTINGS FOR THE RECEIVER ...................... 9 ©2020 3Built LLC Page 1 of 9 10/5/2020... -
Page 2: Standard Transmitter
2) Flip the transmitter over and remove the ring clip. 3) Remove the Philips head screw and gently pry the plastic case open. 4) Remove the circuit board but leave the battery in place. ©2020 3Built LLC Page 2 of 9 10/5/2020... -
Page 3: Programming Transmitter To Receiver
9) The receiver will beep twice. 10) Disconnect power to the Receiver for a few seconds. 11) Connect power to the Receiver and test new Transmitter by pushing the Lock and then the Unlock buttons. ©2020 3Built LLC Page 3 of 9 10/5/2020... -
Page 4: Reset Receiver
10) The receiver will beep twice. 11) Disconnect power to the Receiver for a few seconds. 12) Connect power to the Receiver and test new Transmitter by pushing the Lock and then the Unlock buttons. ©2020 3Built LLC Page 4 of 9 10/5/2020... -
Page 5: Optional Settings For The Receiver
6) Toggle BEEP NOTIFICATION MODE: push button for 17 seconds and release. a. The beeping signals can be disabled, if necessary. No audible signals will be given. b. 1-beep: default mode (beep notification enabled) c. 2-beeps: silent mode is enabled. ©2020 3Built LLC Page 5 of 9 10/5/2020... -
Page 6: Long Range Transmitter
2) Remove the three screws on the back cover 3) Split the front cover from the back cover. 4) Remove the circuit board and battery. Leave battery attached to circuit board. 5) After programming, assemble transmitter in reverse order. ©2020 3Built LLC Page 6 of 9 10/5/2020... -
Page 7: Programming Transmitter To Receiver
9) The receiver will beep twice. 10) Disconnect power to the Receiver for a few seconds. 11) Connect power to the Receiver and test THE Transmitter by pushing the Lock and then the Unlock buttons. ©2020 3Built LLC Page 7 of 9 10/5/2020... -
Page 8: Reset Receiver
10) The receiver will beep twice. 11) Disconnect power to the Receiver for a few seconds. 12) Connect power to the Receiver and test new Transmitter by pushing the Lock and then the Unlock buttons. ©2020 3Built LLC Page 8 of 9 10/5/2020... -
Page 9: Optional Settings For The Receiver
6) Toggle BEEP NOTIFICATION MODE: push button for 17 seconds and release. a. The beeping signals can be disabled, if necessary. No audible signals will be given. b. 1-beep: default mode (beep notification enabled) c. 2-beeps: silent mode is enabled. ©2020 3Built LLC Page 9 of 9 10/5/2020...
Need help?
Do you have a question about the RES126VX and is the answer not in the manual?
Questions and answers