Table of Contents
Advertisement
Quick Links
2800/2801
Environmental Lathe-Enclosure™
1601 J. P . Hennessy Drive, LaVergne, TN USA 37086-3565 615/641-7533 800/688-6359
HENNESSY INDUSTRIES INC. Manufacturer of AMMCO
®
Installation Instructions
Operating Instructions
Safety Instructions
Maintenance Instructions
READ these instructions before placing unit in
service. KEEP these and other materials delivered
with the unit in a binder near the machine for
ease of reference by supervisors and operators.
, COATS
and BADA
Automotive Service Equipment and Tools.
®
®
®
Manual Part No.: 940086 06
Revision:
10/06
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for HENNESSY INDUSTRIES AMMCO 2800
Summary of Contents for HENNESSY INDUSTRIES AMMCO 2800
- Page 1 1601 J. P . Hennessy Drive, LaVergne, TN USA 37086-3565 615/641-7533 800/688-6359 Manual Part No.: 940086 06 HENNESSY INDUSTRIES INC. Manufacturer of AMMCO , COATS and BADA Automotive Service Equipment and Tools.
-
Page 2: Table Of Contents
For additional copies of either, approved replacement parts. or further information, contact: • Keep all instructions permanently with the unit and all Hennessy Industries decals/labels/notices on the unit clean and visible. P.O. Box 3002, 1601 J.P. Hennessy Drive LaVergne, TN 37086-1982 615/641-7533 or 800/688-6359... -
Page 3: General Safety Instructions
General Safety Instructions Before operating the lathe, review the warning information on the lathe and the cautions, warnings and dangers in this manual. Also review the following general safety instructions. Failure to follow safety instructions could result in personal injury to operator or bystanders and damage to the lathe or personal property. - Page 4 iv • 2800/2801 Lathe Enclosures...
-
Page 5: Before You Begin
Before You Begin CAUTION Safety Notices and Decals Prevent accidents and injury, read and follow instructions. For your safety, and the safety of others, read and understand all of the safety notices and decals included here and on the unit. Read entire manual before installing, operating, or servicing... -
Page 6: Receiving
Receiving The shipment should be thoroughly inspected as soon as it is received. The signed bill of lading is acknowledgement by the carrier of receipt in good condition of shipment covered by our invoice. If any of the goods called for on this bill of lading are shorted or damaged, do not accept them until the carrier makes a notation on the freight bill of the shorted or damaged goods. -
Page 7: Installation - 2800 And 2801
This installation procedure Preparing the Bench for Installation CAUTION requires 2 persons to 6. If a lathe is attached to the bench, remove it complete. The enclosure is now. large and heavy and cannot be unpacked, moved, Move the bench to a position where all sides or positioned safely by one person. - Page 8 18. Locate and attach the horizontal mounting 21. Remove the lathe mounting bolts from the bracket to the vertical brackets using 1/4x20 mounting holes in the bench and Enclosure. phillips screws and nuts (fig. 3). Do not 22. Place your lathe inside the Enclosure. tighten.
- Page 9 33. Install the newly constructed spacer brackets 37. When the front of the Enclosure is level within in their appropriate location between the 1/4” and the top cover mates properly to the bench and the vertical brackets with the short lower portion, tighten all fasteners securely.
-
Page 10: Additional Installation - 2801 Only
Additional Installation – 2801 only Electrical Wiring Remove the cover on the round box by taking Assembling Shield out the two screws. Position the shield top & side assembly as shown in fig. 10. 3 Holes In Top Shield Hood Switch Cable Lower Strut Bracket (Ref) Box Mounting Tab... -
Page 11: Operation
Operation Maintenance IMPORTANT: Do not plug fan or lathe into a Check filter regularly wall power source. Fan and lathe power cords contamination. The replacement interval for must be plugged into the Enclosure electrical the filter is directly proportional to use. receptical or the safety features will not Replace the filter when the air flow is function. -
Page 12: Parts Identification 2800 And 2801
Parts Identification 2800 and 2801 ITEM PART NO. QTY. DESCRIPTION ITEM PART NO. QTY. DESCRIPTION 940030 Angle, vertical mounting bracket 940025-01 Bracket, gas strut 940028-01 Spacer, vertical angle mtg-outer 940025-02 Bracket, gas strut 940028-02 Spacer, vertical angle mtg-inner 940084 Screw, ⁄... -
Page 13: Wiring View
Parts Identification – 2801 parts only ITEM PART NO. QTY. DESCRIPTION 40121 Cord, power 40044 Foot switch assy 40051 Relay, SPST, 1 H. P. 40120 Receptacle, duplex, 20A 40125 Switch, hood 40220 Switch, stop 40221 Plate, stop switch Wiring View ITEM PART NO. - Page 14 940086 06 10/06 © COPYRIGHT 1996 HENNESSY INDUSTRIES AND AMMCO TOOLS ALL RIGHTS RESERVED PRINTED IN U.S.A.
Need help?
Do you have a question about the AMMCO 2800 and is the answer not in the manual?
Questions and answers