Advertisement
Quick Links
说明书材质要求:105g铜版纸
专色用6级防晒油墨
第一:
+CMYK油墨要求：
专色用6级防晒油墨):
PANTONE137C专色油墨(
1.
如果自己配色,油墨配比为:泗联中黄(
泗联金红(
C色油墨:泗联天蓝墨
2.
M色油墨:泗联金红墨
3.
4.Y色油墨:pantone123C专色油墨
5.K色油墨:泗联黑墨
折叠方式：骑马钉/胶装/风琴折
如有其他方式再讨论
特别注意：此页内容不印刷
说明书成品尺寸:
第二：特别注意：
1.印刷时看样请参考我司提供的实物样品颜色。不得偏色
2.137C的专色不得参考C=0,M=35,Y=90,K=0对应的四
防晒)
2000g
色色谱颜色来看样印刷
防晒)
225g
备注:
120x170mm
Advertisement
Summary of Contents for iNECO AG110018
- Page 1 说明书材质要求:105g铜版纸 说明书成品尺寸: 120x170mm 专色用6级防晒油墨 第一: +CMYK油墨要求： 第二：特别注意： 1.印刷时看样请参考我司提供的实物样品颜色。不得偏色 专色用6级防晒油墨): PANTONE137C专色油墨( 2.137C的专色不得参考C=0,M=35,Y=90,K=0对应的四 防晒) 如果自己配色,油墨配比为:泗联中黄( 2000g 色色谱颜色来看样印刷 防晒) 泗联金红( 225g C色油墨:泗联天蓝墨 M色油墨:泗联金红墨 4.Y色油墨:pantone123C专色油墨 5.K色油墨:泗联黑墨 备注: 折叠方式：骑马钉/胶装/风琴折 如有其他方式再讨论 特别注意：此页内容不印刷...
- Page 2 Angle Grinder Angle Grinder AG110018 UAG110018 AG110018-4 AG110018-6 AG110018-8 AG110018S AG110018E INGCO Global INGCO Global...
- Page 3 2|English The symbols in instruction manual and the label on the tool Double insulated for additional protection. Read the instruction manual before using. CE conformity. Wear safety glasses, hearing protection and dust mask. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
- Page 4 3|English GENERAL POWER TOOL SAFETY WARNINGS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
- Page 5 4|English a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. Personal safety a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication.
- Page 6 5|English and must be repaired. c) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. d) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool.
- Page 7 6|English Additional Safety Warnings Safety iinstructiions for allll operatiions Safety Warnings Common for Grinding, Sanding, Wire Brushing, Polishing or Abrasive Cutting- Off Operations: a) This power tool is intended to function as a grinder, sander, wire brush, polisher or cut-off tool.
- Page 8 7|English and excessive accumulation of powdered metal may cause electrical hazards. o) Do not operate the power tool near flammable materials. Sparks could ignite these materials. p) Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.
- Page 9 8|English e) Always use undamaged wheel flanges that are of correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges. f) Do not use worn down wheels from larger power tools.
- Page 10 9|English Residual risks Even when the po wer tool is used as prescribed it is not possible to eliminate all residual risk factors. The follo wing hazards may arise in connection with the power tool’s construction and design: a) Health defects resulting from vibration emission if the power tool is being used over longer period of time or not adequately managed and properl y maintained.
- Page 11 10|English 1. Spindle Locking Button 2. On / Off Switch Button 3. Handle 4. Power Cable Sleeve 5. Cooling Vents 6. Auxiliary Handle 7. Disc Guard 8. Direction Of Rotation Indicator 9. Outer Flange 10. Inner Flange...
-
Page 12: Technical Data
Disc bore: Ø22.2mm Ø22.2mm Ø22.2mm Spindle thread: 5/8"-11UNC M 14 Double insulation: Weight: 2.0kg 2.0kg 2.0kg Model No. AG110018S(SAA plug) AG110018-6(ISRAEL plug) AG110018-8(BS plug) Voltage: 220-240V~50/60Hz 220-240V~50/60Hz 220-240V~50/60Hz Input power: 1100W 1100W 1100W No-load speed: 1 000/min 1 000/min 1 000/min... - Page 13 12|English OPERATION INSTRUCTIONS WARNING: Before using your angle grinder be sure to read the instruction manual carefully. INSTALLING THE AUXILIARY HANDLE (see fig 1) An auxiliary handle is supplied and can be fixed into both of the two positions on the gearcase. If you are right handed fit the handle as shown in fig1.
- Page 14 13|English 4. SWITCH (see fig 4) The On/Off trigger switch is sprung in the OFF position. The angle grinder is started by pushing forward the on/off switch. See fig 4. To stop the angle grinder, release the on/off switch and it will return to the OFF position. WARNING! The disc will continue rotate for a few On/off switch button...
-
Page 15: Working Hints For Your Angle Grinder
14|English The abrasive discs operate more efficiently when light pressure is exerted, thus avoiding a drop in the speed of your angle grinder. If your angle grinder becomes too hot, run your angle grinder under no load for 2-3 minutes until it has cooled to normal operation temperature. WORKING HINTS FOR YOUR ANGLE GRINDER 1. - Page 16 15|English AG110018,UAG110018,AG110018-4,AG110018-6, AG110018-8,AG110018S,AG110018E...
- Page 17 16|English AG110018,UAG110018,AG110018-4,AG110018-6, AG110018-8,AG110018S,AG110018E Part Description Part Description Outter flange Armature Inner flange Wheel guard Anti-dust cover Screws with washer M4X16 Bearing 607 Output shaft Bushing Dust cover Front cover Stator Bearing 6201 Housing Insulation washer Gear Coil spring Needle sleeve HK0810...
- Page 18 INGCO TOOLS CO.,LIMITED No.45 Songbei Road,Suzhou MADE IN CHINA Industrial Park,China. 1020.V07 AG110018 UAG110018 AG110018-4 AG110018-6 AG110018-8 AG110018S AG110018E...